JAJSRI9A October   2023  – March 2024 LM51772

ADVANCE INFORMATION  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 概要 (続き)
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 Handling Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Buck-Boost Control Scheme
        1. 8.3.1.1 Buck Mode
        2. 8.3.1.2 Boost Mode
        3. 8.3.1.3 Buck-Boost Mode
      2. 8.3.2  Power Save Mode
      3. 8.3.3  Programmable Conduction Mode PCM
      4. 8.3.4  Reference System
        1. 8.3.4.1 VIO LDO and nRST-PIN
      5. 8.3.5  Supply Voltage Selection – VMAX Switch and Selection Logic
      6. 8.3.6  Enable and Undervoltage Lockout
        1. 8.3.6.1 UVLO
        2. 8.3.6.2 VDET Comparator
      7. 8.3.7  Internal VCC Regulator
        1. 8.3.7.1 VCC1 Regulator
        2. 8.3.7.2 VCC2 Regulator
      8. 8.3.8  Error Amplifier and Control
        1. 8.3.8.1 Output Voltage Regulation
        2. 8.3.8.2 Internal Output Voltage Regulation
        3. 8.3.8.3 Dynamic Voltage Scaling
      9. 8.3.9  Short Circuit - Hiccup Protection
      10. 8.3.10 Current Monitor/Limiter
        1. 8.3.10.1 Overview
        2. 8.3.10.2 Output Current Limitation
        3. 8.3.10.3 Output Current Monitor
      11. 8.3.11 Oscillator Frequency Selection
      12. 8.3.12 Frequency Synchronization
      13. 8.3.13 Output Voltage Tracking
        1. 8.3.13.1 Analog Voltage Tracking
        2. 8.3.13.2 Digital Voltage Tracking
      14. 8.3.14 Slope Compensation
      15. 8.3.15 Configurable Soft Start
      16. 8.3.16 Drive Pin
      17. 8.3.17 Dual Random Spread Spectrum – DRSS
      18. 8.3.18 Gate Driver
      19. 8.3.19 Cable Drop Compensation (CDC)
      20. 8.3.20 CFG-pin and R2D Interface
      21. 8.3.21 Advanced Monitoring Features
        1. 8.3.21.1  Overview
        2. 8.3.21.2  BUSY
        3. 8.3.21.3  OFF
        4. 8.3.21.4  VOUT
        5. 8.3.21.5  IOUT
        6. 8.3.21.6  INPUT
        7. 8.3.21.7  TEMPERATURE
        8. 8.3.21.8  CML
        9. 8.3.21.9  OTHER
        10. 8.3.21.10 ILIM_OP
        11. 8.3.21.11 nFLT/nINT Pin Output
        12. 8.3.21.12 Status Byte
      22. 8.3.22 Protection Features
        1. 8.3.22.1  Thermal Shutdown (TSD)
        2. 8.3.22.2  Over Current Protection
        3. 8.3.22.3  Output Over Voltage Protection 1 (OVP1)
        4. 8.3.22.4  Output Over Voltage Protection 2 (OVP2)
        5. 8.3.22.5  Input Voltage Protection (IVP)
        6. 8.3.22.6  Input Voltage Regulation (IVR)
        7. 8.3.22.7  Power Good
        8. 8.3.22.8  Boot-Strap Under Voltage Protection
        9. 8.3.22.9  Boot-strap Over Voltage Clamp
        10. 8.3.22.10 CRC - CHECK
    4. 8.4 Device Functional Modes
      1. 8.4.1 Overview
      2. 8.4.2 Logic State Description
    5. 8.5 Programming
      1. 8.5.1 I2C Bus Operation
      2. 8.5.2 Clock Stretching
      3. 8.5.3 Data Transfer Formats
      4. 8.5.4 Single READ from a Defined Register Address
      5. 8.5.5 Sequential READ Starting from a Defined Register Address
      6. 8.5.6 Single WRITE to a Defined Register Address
      7. 8.5.7 Sequential WRITE Starting at a Defined Register Address
  10. 9 LM51772 Registers
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1  Custom Design with WEBENCH Tools
        2. 10.2.2.2  Frequency
        3. 10.2.2.3  Feedback Divider
        4. 10.2.2.4  Inductor and Current Sense Resistor Selection
        5. 10.2.2.5  Output Capacitor
        6. 10.2.2.6  Input Capacitor
        7. 10.2.2.7  Slope Compensation
        8. 10.2.2.8  UVLO Divider
        9. 10.2.2.9  Soft-Start Capacitor
        10. 10.2.2.10 MOSFETs QH1 and QL1
        11. 10.2.2.11 MOSFETs QH2 and QL2
        12. 10.2.2.12 Loop Compensation
        13. 10.2.2.13 External Component Selection
      3. 10.2.3 Application Curves
    3. 10.3 Power Supply Recommendations
    4. 10.4 Layout
      1. 10.4.1 Layout Guidelines
        1. 10.4.1.1 Power Stage Layout
        2. 10.4.1.2 Gate Driver Layout
        3. 10.4.1.3 Controller Layout
      2. 10.4.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 ドキュメントの更新通知を受け取る方法
    3. 11.3 サポート・リソース
    4. 11.4 Trademarks
    5. 11.5 静電気放電に関する注意事項
    6. 11.6 用語集
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

6.6 Timing Requirements

Over operating junction temperature range and recommended supply voltage range (unless otherwise noted)
MIN NOM MAX UNIT
OVERALL DEVICE FEATURES
Minimum time low EN toggle  time measured from EN toggle from H to L and from L to H TBD µs
I2C INTERFACE
fSCL SCL clock frequency Standard mode 0 100 kHz
Fast mode 0 400
Fast mode plus (1) 0 1000
tLOW LOW period of the SCL clock Standard mode 4.7 µs
Fast mode 1.3
Fast mode plus (1) 0.5
tHIGH HIGH period of the SCL clock Standard mode 4.0 µs
Fast mode 0.6
Fast mode plus (1) 0.26
tBUF Bus free time between a STOP and
a START condition		 Standard mode 4.7 µs
Fast mode 1.3
Fast mode plus (1) 0.5
tSU:STA Set-up time for a repeated START
condition		 Standard mode 4.7 µs
Fast mode 0.6
Fast mode plus (1) 0.26
tHD:STA Hold time (repeated) START
condition		 Standard mode 4.0 µs
Fast mode 0.6
Fast mode plus (1) 0.26
tHD:DAT Data hold time Standard mode 0 µs
Fast mode 0
Fast mode plus (1) 0
tr Rise time of both SDA and SCL
signals		 Standard mode 1000 ns
Fast mode 20 300
Fast mode plus (1) 20
tf Fall time of both SDA and SCL
signals		 Standard mode 300 ns
Fast mode 20×VDD/5.5 300
Fast mode plus (1) 20×VDD/5.5 120
tsu:STO Set-up time for STOP condition Standard mode 4.0 µs
Fast mode 0.6
Fast mode plus (1) 0.26
tVD;DAT Data valid time Standard mode 3.45 µs
Fast mode 0.9
Fast mode plus (1) 0.45
tVD;ACK Data valid acknowledge time Standard mode 3.45 µs
Fast mode 0.9
Fast mode plus (1) 0.45
Cb Capacitive load for each bus line Standard mode 400 pF
Fast mode 400
(1) Fast mode plus is supported but not fully compliant with I2C standard