SLOSE54C June   2020  – July 2022 DRV8428

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
    1. 5.1 Pin Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Indexer Timing Requirements
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Stepper Motor Driver Current Ratings
        1. 7.3.1.1 Peak Current Rating
        2. 7.3.1.2 RMS Current Rating
        3. 7.3.1.3 Full-Scale Current Rating
      2. 7.3.2 PWM Motor Drivers
      3. 7.3.3 Microstepping Indexer
      4. 7.3.4 Controlling VREF with an MCU DAC
      5. 7.3.5 Current Regulation, Off-time and Decay Modes
        1. 7.3.5.1 Mixed Decay
        2. 7.3.5.2 Smart tune Dynamic Decay
        3. 7.3.5.3 Smart tune Ripple Control
        4. 7.3.5.4 Blanking time
      6. 7.3.6 Linear Voltage Regulators
      7. 7.3.7 Logic Level, tri-level, quad-level and seven-level Pin Diagrams
        1. 7.3.7.1 EN/nFAULT Pin
      8. 7.3.8 Protection Circuits
        1. 7.3.8.1 VM Undervoltage Lockout (UVLO)
        2. 7.3.8.2 Overcurrent Protection (OCP)
        3. 7.3.8.3 Thermal Shutdown (OTSD)
        4. 7.3.8.4 Fault Condition Summary
    4. 7.4 Device Functional Modes
      1. 7.4.1 Sleep Mode (nSLEEP = 0)
      2. 7.4.2 Disable Mode (nSLEEP = 1, EN/nFAULT = 0/Hi-Z)
      3. 7.4.3 Operating Mode (nSLEEP = 1, EN/nFAULT = 1)
      4. 7.4.4 Functional Modes Summary
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Stepper Motor Speed
        2. 8.2.2.2 Current Regulation
        3. 8.2.2.3 Decay Modes
        4. 8.2.2.4 Application Curves
      3. 8.2.3 Thermal Application
        1. 8.2.3.1 Power Dissipation
          1. 8.2.3.1.1 Conduction Loss
          2. 8.2.3.1.2 Switching Loss
          3. 8.2.3.1.3 Power Dissipation Due to Quiescent Current
          4. 8.2.3.1.4 Total Power Dissipation
        2. 8.2.3.2 Device Junction Temperature Estimation
  9. 9 Power Supply Recommendations
    1. 9.1 Bulk Capacitance
  10. 10Layout
    1. 10.1 Layout Guidelines
      1. 10.1.1 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Community Resources
    4. 11.4 Trademarks
  12. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.2.2.1 Stepper Motor Speed

The first step in configuring the DRV8428 requires the desired motor speed and microstepping level. If the target application requires a constant speed, then a square wave with frequency ƒstep must be applied to the STEP pin. If the target motor speed is too high, the motor does not spin. Make sure that the motor can support the target speed. Use Equation 1 to calculate ƒstep for a desired motor speed (v), microstepping level (nm), and motor full step angle (θstep)

Equation 1. GUID-FF5F0738-FBD3-4167-A8F6-484E813A45E4-low.gif

The value of θstep can be found in the stepper motor data sheet, or written on the motor. For example, the motor in this application is required to rotate at 1.8°/step for a target of 18.75 rpm at 1/8 microstep mode. Using Equation 1, ƒstep can be calculated as 500 Hz.

The microstepping level is set by the M0 and M1 pins and can be any of the settings listed in Table 8-2. Higher microstepping results in a smoother motor motion and less audible noise, but requires a higher ƒstep to achieve the same motor speed.

Table 8-2 Microstepping Indexer Settings
M0M1STEP MODE
00Full step (2-phase excitation) with 100% current
0330 kΩ to GNDFull step (2-phase excitation) with 71% current
10Non-circular 1/2 step
Hi-Z01/2 step
011/4 step
111/8 step
Hi-Z11/16 step
0Hi-Z1/32 step
Hi-Z330 kΩ to GND1/64 step
Hi-ZHi-Z1/128 step
1Hi-Z1/256 step