SDLS967H may   2016  – july 2023 LSF0108-Q1

PRODMIX  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information (Q1)
    5. 6.5 Electrical Characteristics - RKS Package
    6. 6.6 Electrical Characteristics - PW Package
    7. 6.7 Switching Characteristics (Translating Down)
    8. 6.8 Switching Characteristics (Translating Up)
    9. 6.9 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Auto Bidirectional Voltage Translation
      2. 8.3.2 Output Enable
      3. 8.3.3 Wettable Flanks
    4. 8.4 Device Functional Modes
      1. 8.4.1 Up and Down Translation
  10. 9 Applications and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 I2C PMBus, SMBus, GPIO
        1. 9.2.1.1 Design Requirements
          1. 9.2.1.1.1 Enable, Disable, and Reference Voltage Guidelines
          2. 9.2.1.1.2 Bias Circuitry
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Bidirectional Translation
          2. 9.2.1.2.2 Pull-Up Resistor Sizing
          3. 9.2.1.2.3 LSF0108-Q1 Bandwidth
        3. 9.2.1.3 Application Curves
      2. 9.2.2 Mixed-Mode Voltage Translation
        1. 9.2.2.1 Single Supply Translation
        2. 9.2.2.2 Voltage Translation for Vref_B < Vref_A + 0.8 V
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Receiving Notification of Documentation Updates
    2. 10.2 Support Resources
    3. 10.3 Trademarks
    4. 10.4 Electrostatic Discharge Caution
    5. 10.5 Glossary
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.1 Application Information

The LSF0108-Q1 device can perform voltage translation for open-drain or push-pull interface. Table 9-1 provides some consumer or telecom interfaces as reference to the different channel numbers that are supported by the LSF0108-Q1.

Table 9-1 Voltage Translator for Consumer or Telecom Interface
Part NameChannel NumberInterface
LSF0108-Q18GPIO, MDIO, SDIO, SVID, UART, SMBus, PMBus, I2C, and SPI

Some important reminders regarding the LSF family of devices are as follows:

  • LSF devices are switch-based, not buffer-based (see the TXB family for buffer-based devices)
  • Specific data rates cannot be calculated by using 1/Tpd
  • VCCB/VCCA are not the same as Vref_B or Vref_A: VCCB refers to the B-side supply voltage supplied to the LSF device, while Vref_B refers to the voltage at the Vref_B pin (pin 7 of Figure 9-1) on the other side of the 200 kΩ resistor