SBAU358A November   2020  – June 2025 AFE10004

 

  1.   1
  2.   Description
  3.   Get Started
  4.   Features
  5.   Applications
  6.   6
  7. 1Evaluation Module Overview
    1. 1.1 Introduction
    2. 1.2 Kit Contents
    3. 1.3 Specification
    4. 1.4 Device Information
  8. 2Hardware
    1. 2.1 Power Requirements
      1. 2.1.1 Configuring the EVM for a Positive Output Range
      2. 2.1.2 Configuring the EVM for a Negative Output Range
    2. 2.2 Header Information
    3. 2.3 Jumper Information
    4. 2.4 Interfaces
      1. 2.4.1 SPI Configuration
      2. 2.4.2 I2C Configuration
    5. 2.5 Test Points
  9. 3Software
    1. 3.1 Software Installation
    2. 3.2 Software Description
      1. 3.2.1 Launching the Software
      2. 3.2.2 Low Level Configuration Page
      3. 3.2.3 Block Diagram Page
      4. 3.2.4 Look Up Table Page
        1. 3.2.4.1 Loading and Saving LUT Files
  10. 4Hardware Design Files
    1. 4.1 Schematics
    2. 4.2 PCB Layouts
    3. 4.3 Bill of Materials (BOM)
  11. 5Additional Information
    1. 5.1 Electrostatic Discharge Caution
    2. 5.2 Trademarks
  12. 6Related Documentation
  13. 7Revision History

2.2 Header Information

Table 2-1 defines the AFE10004EVM output header J1.

Table 2-1 Output Header J1
Pin Definition
2 OUT2
4 DAC2
6 CLAMP2
8 DAC3
10 DAC0
12 CLAMP1
14 DAC1
16 OUT1
18 PA_ON
1, 3, 5, 7, 9, 11, 13, 15, 17 GND

Table 2-2 defines the AFE10004EVM digital header J3.

Table 2-2 Digital Header J3
Pin Definition
2 RESET/ALARMIN
4 DRVEN2
6 DRVEN1
8 SDA
10 SCL
12 A2/SCLK
14 A1/MOSI
16 A0/MISO
1, 3, 5, 7, 9, 11, 13, 15 GND

Table 2-7 shows the power connector definitions of the AFE10004EVM.

Table 2-3 Power Connector Definitions
Designator Definition
J1 USB connector
B1 AFE10004 VIO supply (1.65V to 3.6V)
B2 AFE10004 VDD supply (4.5V to 5.5V)
B3 AFE10004 VCC supply (0V to 5.5V)
B4 AFE10004 Ground
B5 AFE10004 VSS supply (0V to –11V)

Table 2-4 shows the output connector definitions of the AFE10004EVM.

Table 2-4 Output Connector Definitions
Designator Definition
J6 SMA connector for FT4232 trigger output (unpopulated)
J14 SMA connector for AFE10004 OUT1 (unpopulated)
J15 SMA connector for AFE10004 OUT2 (unpopulated)
J16 SMA connector for AFE10004 DAC0 (unpopulated)
J17 SMA connector for AFE10004 DAC3 (unpopulated)