SLAAED1G May   2023  – August 2025 MSPM0C1103 , MSPM0C1103-Q1 , MSPM0C1104 , MSPM0C1104-Q1 , MSPM0C1105 , MSPM0C1106 , MSPM0C1106-Q1 , MSPM0G1105 , MSPM0G1106 , MSPM0G1107 , MSPM0G1505 , MSPM0G1506 , MSPM0G1507 , MSPM0G1518 , MSPM0G1519 , MSPM0G3105 , MSPM0G3105-Q1 , MSPM0G3106 , MSPM0G3106-Q1 , MSPM0G3107 , MSPM0G3107-Q1 , MSPM0G3505 , MSPM0G3505-Q1 , MSPM0G3506 , MSPM0G3506-Q1 , MSPM0G3507 , MSPM0G3507-Q1 , MSPM0G3518 , MSPM0G3518-Q1 , MSPM0G3519 , MSPM0G3519-Q1 , MSPM0H3216 , MSPM0H3216-Q1 , MSPM0L1105 , MSPM0L1106 , MSPM0L1116 , MSPM0L1117 , MSPM0L1227 , MSPM0L1227-Q1 , MSPM0L1228 , MSPM0L1228-Q1 , MSPM0L1303 , MSPM0L1304 , MSPM0L1304-Q1 , MSPM0L1305 , MSPM0L1305-Q1 , MSPM0L1306 , MSPM0L1306-Q1 , MSPM0L1343 , MSPM0L1344 , MSPM0L1345 , MSPM0L1346 , MSPM0L2227 , MSPM0L2227-Q1 , MSPM0L2228 , MSPM0L2228-Q1

 

  1.   1
  2.   Abstract
  3.   Trademarks
  4. 1 Overview
  5. 2 MSPM0 Online Selection
  6. 3 Software Development Instructions
    1. 3.1 Key Documentation
    2. 3.2 LaunchPad Setup
      1. 3.2.1 Debugger Selection
      2. 3.2.2 LaunchPad Introduction
    3. 3.3 MSPM0-SDK Setup
      1. 3.3.1 MSPM0-SDK Installation
      2. 3.3.2 MSPM0-SDK Introduction
        1. 3.3.2.1 Examples Folder Introduction
        2. 3.3.2.2 Documents Folder Introduction
    4. 3.4 SysConfig Setup
      1. 3.4.1 SysConfig Installation
      2. 3.4.2 SysConfig Introduction
        1. 3.4.2.1 Basic Concept
        2. 3.4.2.2 Project Configuration View
        3. 3.4.2.3 Board View
        4. 3.4.2.4 NONMAIN View
        5. 3.4.2.5 SYSCTL View
        6. 3.4.2.6 Peripherals Setup
    5. 3.5 IDE Quick Start
      1. 3.5.1 CCS Quick Start
        1. 3.5.1.1 CCS Installation
        2. 3.5.1.2 Import a SDK Example
        3. 3.5.1.3 Example Download and Debug
        4. 3.5.1.4 Migrating Between MSPM0 Derivatives
        5. 3.5.1.5 Generate Hex Files
        6. 3.5.1.6 Program NONMAIN
      2. 3.5.2 IAR Quick Start
        1. 3.5.2.1 Environment Setup
          1. 3.5.2.1.1 SDK Support Setup
          2. 3.5.2.1.2 SysConfig Support Setup
        2. 3.5.2.2 Import a SDK Example
        3. 3.5.2.3 Example Download and Debug
        4. 3.5.2.4 Migrating Between MSPM0 Derivatives
        5. 3.5.2.5 Generate Hex Files
        6. 3.5.2.6 Program NONMAIN
      3. 3.5.3 Keil Quick Start
        1. 3.5.3.1 Environment Setup
          1. 3.5.3.1.1 MSPM0 CMSIS-Pack Setup
          2. 3.5.3.1.2 Sysconfig Support Setup
        2. 3.5.3.2 Import a SDK Example
        3. 3.5.3.3 Example Download and Debug
        4. 3.5.3.4 Migrating Between MSPM0 Derivatives
        5. 3.5.3.5 Generate Hex Files
        6. 3.5.3.6 Program NONMAIN
  7. 4 Hardware Design Instructions
    1. 4.1 Obtaining a MSPM0 Package
    2. 4.2 Fix Pin Functions through Sysconfig
    3. 4.3 Schematic and PCB Attentions
  8. 5 Mass Production Instructions
    1. 5.1 Generate Production Image
    2. 5.2 Program Software Tools Quick Start
      1. 5.2.1 Uniflash Quick Start
        1. 5.2.1.1 Program Through SWD
        2. 5.2.1.2 Program Through Bootloader
        3. 5.2.1.3 Program Through CMD Line Interface
      2. 5.2.2 JFlash Quick Start
      3. 5.2.3 C-GANG Quick Start
    3. 5.3 Program Hardware Quick Start
  9. 6 Quality and Reliability Instructions
    1. 6.1 Quality and Reliability Material Entrance
    2. 6.2 Failure Information Collection and Analysis Guidance
  10. 7 Common Development Questions
    1. 7.1 Unlock MCU
      1. 7.1.1 Unlock Through Bootloader
      2. 7.1.2 Unlock Through Factory Reset GUI Tool
      3. 7.1.3 Unlock Through Uniflash
      4. 7.1.4 Unlock Through CCS
      5. 7.1.5 Unlock With Reset Pin Disabled
    2. 7.2 MSPM0 Program Failure
    3. 7.3 Attentions When Disabling SWD or REST Pin
    4. 7.4 MCU Performs Differently in Debug and Free Run
    5. 7.5 Set SWD Password
    6. 7.6 BSL Related Questions
    7. 7.7 Reach Expected Current in LPM Mode
    8. 7.8 CCS Common Questions
      1. 7.8.1 Change the Optimization Level
    9. 7.9 Keil Common Questions
      1. 7.9.1 Copy Keil Example Out of SDK
  11. 8 Summary
  12. 9 Technical Documentation Resources
    1. 9.1 Technical Reference Manuals
    2. 9.2 Subsystems
    3. 9.3 Reference Designs
    4. 9.4 Hardware EVM User's Guides
    5. 9.5 Application Briefs
    6. 9.6 Application Notes and Others
  13. 10Revision History

5.2.3 C-GANG Quick Start

This section shows how to use C-GANG to do the MSPM0 online and offline program. For more advanced usage, like setting password or factory reset, refer to the user's guide in the C-GANG product page and TI-CGANG-MSPM0 video.

  1. Follow the steps below to finish GangPro-ARM GUI installation and USB driver installation.
    GangPro-ARM Install Figure 5-5 GangPro-ARM Install
  2. Finish connection between C-GANG and the connector board, as shown in Figure 5-6. Finish the pin connection between MSPM0 and C-GANG. The least used pins are VCC, GND, SWDIO, SWCLK. If users want to use Clear Locked Device function, then the reset pin is also needed.
    C-Gang Pin Assignment Figure 5-6 C-Gang Pin Assignment
  3. After the hardware setup is finished, follow the programming steps. If users open the GUI, then users can go through step 2 to scan the C-GANG. In step 3, see Section 5.1 to generate the code file. Remember to choose the suitable interface. The enabled target is related to the hardware port used, which is labeled numerically next to the port.
    Online Program Figure 5-7 Online Program
  4. To change the code file in the non-main (SWD and BSL configure flash area), click the Enable button in the memory protection region. If this is not needed, then keep this disabled.
    Enable Non-Main Programming Figure 5-8 Enable Non-Main Programming
  5. Save the code file and settings (Image) into C-GANG.
    Save Image Figure 5-9 Save Image
  6. Set the function for GO button.
    Go Button Setting Figure 5-10 Go Button Setting
  7. Now that the image is downloaded into C-GANG, users can close the GUI to do the programming by pressing the green button.
    Offline Downloading Figure 5-11 Offline Downloading
  8. If the device is locked, C-GANG also support to unlock the device through doing factory reset. First, please connect VCC, GND, SWDIO, SWCLK, RST. Then flow the instruction as shown in Figure 5-12.
    Factory Reset with C-GANG Figure 5-12 Factory Reset with C-GANG