SLASFH8 March   2026 MSPM33C321A-Q1

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Functional Block Diagram
  6. 5 Device Comparison
  7. 6 Pin Configuration and Functions
    1. 6.1 Pin Diagrams
    2. 6.2 Pin Attributes
      1.      10
    3. 6.3 Signal Descriptions
      1.      12
      2.      13
      3.      14
      4.      15
      5.      16
      6.      17
      7.      18
      8.      19
      9.      20
      10.      21
      11.      22
      12.      23
      13.      24
      14.      25
      15.      26
      16.      27
    4. 6.4 Connections for Unused Pins
  8. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Supply Current Characteristics
      1. 7.5.1 RUN/SLEEP Modes
      2. 7.5.2 STOP/STANDBY Modes
      3. 7.5.3 SHUTDOWN Mode
      4. 7.5.4 VBAT current consumption
    6. 7.6  Flash Memory Characteristics
    7. 7.7  Power Supply Sequencing
      1. 7.7.1 Power Supply Ramp
      2. 7.7.2 POR and BOR
      3. 7.7.3 VBat Characteristics
      4. 7.7.4 Timing Characteristics
    8. 7.8  Clock Specifications
      1. 7.8.1 System Oscillator (SYSOSC)
      2. 7.8.2 High Frequency Crystal/Clock
      3. 7.8.3 System Phase Lock Loop (SYSPLL)
      4. 7.8.4 Low Frequency Oscillator (LFOSC)
      5. 7.8.5 Low Frequency Crystal/Clock
    9. 7.9  Analog Specifications
      1. 7.9.1 ADC Specifications
        1. 7.9.1.1 ADC Electrical Characteristics
        2. 7.9.1.2 ADC Switching Characteristics
        3. 7.9.1.3 ADC Linearity Parameters
        4. 7.9.1.4 Typical Connection Diagram
      2. 7.9.2 COMP Specifications
        1. 7.9.2.1 Comparator Electrical Characteristics
        2. 7.9.2.2 COMP DAC Electrical Characteristics
      3. 7.9.3 VREF Specifications
        1. 7.9.3.1 VREF Voltage Characteristics
        2. 7.9.3.2 VREF Electrical Characteristics
      4. 7.9.4 Analog VBOOST Specification
        1. 7.9.4.1 Analog Mux VBOOST
      5. 7.9.5 Temperature Sensor
    10. 7.10 Serial Interface Specifications
      1. 7.10.1 UART
        1. 7.10.1.1 UART
      2. 7.10.2 I2C
        1. 7.10.2.1 I2C Characteristics
        2. 7.10.2.2 I2C Filter
        3. 7.10.2.3 I2C Timing Diagram
      3. 7.10.3 SPI
        1. 7.10.3.1 SPI
        2. 7.10.3.2 SPI Timing Diagram
      4. 7.10.4 CAN
        1. 7.10.4.1 CAN
      5. 7.10.5 QSPI
        1. 7.10.5.1 QSPI
        2. 7.10.5.2 QSPI Timing Diagram
      6. 7.10.6 I2S/TDM
        1. 7.10.6.1 Serial Audio
        2. 7.10.6.2 I2S/TDM Timing Diagram
    11. 7.11 Digital IO
    12. 7.12 TRNG
      1. 7.12.1 TRNG Electrical Characteristics
      2. 7.12.2 TRNG Switching Characteristics
    13. 7.13 Emulation and Debug
      1. 7.13.1 SWD Timing
  9. 8 Detailed Description
    1. 8.1  Arm Cortex-M33 core with TrustZone and FPU
    2. 8.2  Power Management and Clock Unit (PMCU)
      1. 8.2.1 Power Management Unit (PMU)
      2. 8.2.2 Clock Module (CKM)
      3. 8.2.3 Operating Modes
        1. 8.2.3.1 Functionality by Operating Mode
    3. 8.3  Device Memory Map
      1. 8.3.1 Memory Organization
      2. 8.3.2 Peripheral Memory Map
    4. 8.4  NVIC Interrupt Map
    5. 8.5  Embedded Flash Memory
    6. 8.6  Embedded SRAM
    7. 8.7  DMA
    8. 8.8  Event Manager
    9. 8.9  Error Aggregator Module (EAM)
    10. 8.10 GPIO
    11. 8.11 IOMUX
      1. 8.11.1 Input/Output Diagrams
    12. 8.12 Analog Modules
      1. 8.12.1 HSADC
      2. 8.12.2 COMP
      3. 8.12.3 Temperature Sensor
      4. 8.12.4 VREF
      5. 8.12.5 Device Analog Connections
    13. 8.13 Security and Cryptography
      1. 8.13.1 Global Security Controller (GSC)
      2. 8.13.2 AESADV
      3. 8.13.3 SHA256
      4. 8.13.4 Public Key Algorithm (PKA)
      5. 8.13.5 TRNG
      6. 8.13.6 Keystore
      7. 8.13.7 CRC
    14. 8.14 Serial Communication Interfaces
      1. 8.14.1 UNICOMM (UART/I2C/SPI)
        1. 8.14.1.1 UART (UNICOMM)
        2. 8.14.1.2 I2C (UNICOMM)
        3. 8.14.1.3 SPI (UNICOMM)
      2. 8.14.2 CAN-FD
      3. 8.14.3 Quad SPI (QSPI)
      4. 8.14.4 Digital Audio Interface - I2S/TDM
    15. 8.15 LFSS
    16. 8.16 Timers, RTC and Watchdogs
      1. 8.16.1 Timers (TIMx)
      2. 8.16.2 RTC_A
      3. 8.16.3 IWDT
      4. 8.16.4 WWDT
    17. 8.17 Serial Wire Debug Interface
    18. 8.18 Bootstrap Loader (BSL)
    19. 8.19 Device Factory Constants
    20. 8.20 Identification
  10. 9 Applications, Implementation, and Layout
    1. 9.1 Typical Application
      1. 9.1.1 Schematic
  11. 10Device and Documentation Support
    1. 10.1 Getting Started and Next Steps
    2. 10.2 Device Nomenclature
    3. 10.3 Tools and Software
    4. 10.4 Documentation Support
    5. 10.5 Support Resources
    6. 10.6 Trademarks
    7. 10.7 Electrostatic Discharge Caution
    8. 10.8 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

Digital IO

over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER TEST CONDITIONS(1) MIN TYP MAX UNIT
Electrical Characteristics
VIH High level input voltage All I/O except Reset 0.7*VDD VDD+0.3 V
Reset pin 0.85*VDD VDD+0.3 V
VIL Low level input voltage All I/O except Reset -0.3 0.3*VDD
Reset pin -0.3 0.15*VDD
VHYS Hysteresis All I/O except Reset 0.1*VDD
Reset pin 0.3*VDD
Ilkg High-Z leakage current(2)(3) SDIO 50 nA
HSIO 200 nA
HDIO 280 nA
RPU Pull up resistance 40 kΩ
RPD Pull down resistance 40 kΩ
CI Input capacitance 5 pF
VOH High level output voltage SDIO VDD≥2.7V, IIO=–6mA
VDD≥1.71V, IIO=–2mA
VDD-0.4 V
HSIO VDD≥2.7V, DRV=1, IIO=–6mA
VDD≥1.71V, DRV=1, IIO=–3mA
VDD-0.4
VDD≥2.7V, DRV=0, IIO=–4mA
VDD≥1.71V, DRV=0, IIO=–2mA
VDD-0.4
HDIO VDD≥2.7V, DRV=1, IIO=–20mA
VDD≥1.71V, DRV=1, IIO=–10mA
VDD-0.4
VDD≥2.7V, DRV=0, IIO=–6mA
VDD≥1.71V, DRV=0, IIO=–2mA
VDD-0.4
VOL Low level output voltage SDIO VDD≥2.7V, IIO=6mA
VDD≥1.71V, IIO=2mA
0.4 V
HSIO VDD≥2.7V, DRV=1, IIO=6mA
VDD≥1.71V, DRV=1, IIO=3mA
0.4
VDD≥2.7V, DRV=0, IIO=4mA
VDD≥1.71V, DRV=0, IIO=2mA
0.4
HDIO VDD≥2.7V, DRV=1, IIO=20mA
VDD≥1.71V, DRV=1, IIO=10mA
0.4
VDD≥2.7V, DRV=0, IIO=6mA
VDD≥1.71V, DRV=0, IIO=2mA
0.4
Switching Characteristics
fmax Port output frequency SDIO (1) VDD ≥ 2.7V, CL= 20pF 32 MHz
VDD ≥ 1.71V, CL= 20pF 16
HSIO VDD ≥ 2.7V, DRV = 1, CL= 20pF 40
VDD ≥ 2.7V, DRV = 0, CL= 20pF 32
VDD ≥ 1.71V, DRV = 1, CL= 20pF 24
VDD ≥ 1.71V, DRV = 0, CL= 20pF 16
HDIO VDD ≥ 2.7V, DRV = 1(4), CL= 20pF 20
VDD ≥ 2.7V, DRV = 0, CL= 20pF 20
VDD ≥ 1.71V, DRV = 1(4), CL= 20pF 16
VDD ≥ 1.71V, DRV = 0, CL= 20pF 16
tr,tf Output rise/fall time SDIO VDD ≥ 2.7V, CL = 20pF 3.5 ns
VDD ≥ 1.71V, CL = 20pF 6.6
HSIO VDD ≥ 2.7V, DRV = 1, CL = 20pF 1.8
VDD ≥ 2.7V, DRV = 0, CL = 20pF 5.9
VDD ≥ 1.71V, DRV = 1, CL = 20pF 3.7
VDD ≥ 1.71V, DRV = 0, CL = 20pF 12.6
HDIO VDD ≥ 2.7V, DRV = 1, CL = 20pF 1.7
VDD ≥ 2.7V, DRV = 0, CL = 20pF 3.8
VDD ≥ 1.71V, DRV = 1, CL = 20pF 3.1
VDD ≥ 1.71V, DRV = 0, CL = 20pF 8.2
The sum of the |IIO| current sourced or sunk by the device must always respect the absolute maximum rating
The leakage current is measured with VSS or VDD applied to the corresponding pin(s), unless otherwise noted.
The leakage of the digital port pins is measured individually. The port pin is selected for input and the pullup/pulldown resistor is disabled.
When operating a HDIO in DRV=1 high drive strength configuration, a series resistor is ncessary to limit the signal slew rate