SLLSFM2A November   2024  – October 2025 TCAN2855-Q1 , TCAN2857-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  IEC ESD Ratings
    4. 6.4  Recommended Operating Conditions
    5. 6.5  Thermal Information
    6. 6.6  Supply Characteristics
    7. 6.7  Electrical Characteristics
    8. 6.8  Timing Requirements
    9. 6.9  Switching Characteristics
    10. 6.10 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  VSUP Pin
      2. 8.3.2  VCC1 Regulator
      3. 8.3.3  VCC2 Regulator
        1. 8.3.3.1 VCC2 Short to Battery Protection
      4. 8.3.4  nRST Pin
      5. 8.3.5  VEXCC Regulator
      6. 8.3.6  CAN FD Transceiver
        1. 8.3.6.1 Driver and Receiver Function
        2. 8.3.6.2 CAN Bus Biasing
      7. 8.3.7  LIN Transceiver
        1. 8.3.7.1 LIN Transmitter Characteristics
        2. 8.3.7.2 LIN Receiver Characteristics
        3. 8.3.7.3 LIN Termination
      8. 8.3.8  GND
      9. 8.3.9  LIMP Pin
      10. 8.3.10 High-side Switches (HSS1- HSS4)
      11. 8.3.11 WAKE1, WAKE2 and WAKE3/DIR Pins
        1. 8.3.11.1 WAKE Pins Alternate Configurations
          1. 8.3.11.1.1 VBAT monitoring
          2. 8.3.11.1.2 Direct Drive
      12. 8.3.12 SDO Pin
      13. 8.3.13 nCS Pin
      14. 8.3.14 SCK Pin
      15. 8.3.15 SDI Pin
      16. 8.3.16 Interrupt Function (nINT)
      17. 8.3.17 SW Pin
      18. 8.3.18 GFO Pin
    4. 8.4 Device Functional Modes
      1. 8.4.1 Init Mode
      2. 8.4.2 Normal Mode
      3. 8.4.3 Standby Mode
      4. 8.4.4 Restart Mode
      5. 8.4.5 Fail-safe Mode
        1. 8.4.5.1 SBC Faults
        2. 8.4.5.2 CAN Transceiver Faults
        3. 8.4.5.3 LIN Transceiver Faults ( TCAN2857-Q1)
      6. 8.4.6 Sleep Mode
      7. 8.4.7 Wake Functions
        1. 8.4.7.1 CAN Bus Wake Using CRXD Request (BWRR) in Sleep Mode
        2. 8.4.7.2 LIN Bus Wake
        3. 8.4.7.3 Local Wake Up (LWU) via WAKEx Input Terminal
          1. 8.4.7.3.1 Static Wake
          2. 8.4.7.3.2 Cyclic Sensing Wake
        4. 8.4.7.4 Cyclic Wake
        5. 8.4.7.5 Direct Drive in Sleep Mode
        6. 8.4.7.6 Selective Wake-up
          1. 8.4.7.6.1 Selective Wake Mode
          2. 8.4.7.6.2 Frame Detection
          3. 8.4.7.6.3 Wake-Up Frame (WUF) Validation
          4. 8.4.7.6.4 WUF ID Validation
          5. 8.4.7.6.5 WUF DLC Validation
          6. 8.4.7.6.6 WUF Data Validation
          7. 8.4.7.6.7 Frame Error Counter
          8. 8.4.7.6.8 CAN FD Frame Tolerance
          9. 8.4.7.6.9 8Mbps Filtering
      8. 8.4.8 Protection Features
        1. 8.4.8.1  Fail-safe Features
          1. 8.4.8.1.1 Sleep Mode Using Sleep Wake Error
        2. 8.4.8.2  Device Reset
        3. 8.4.8.3  Floating Terminals
        4. 8.4.8.4  TXD Dominant Time Out (DTO)
        5. 8.4.8.5  LIN Bus Stuck Dominant System Fault: False Wake Up Lockout
        6. 8.4.8.6  CAN Bus Short Circuit Current Limiting
        7. 8.4.8.7  Thermal Shutdown
        8. 8.4.8.8  Under and Over Voltage Lockout and Unpowered Device
          1. 8.4.8.8.1 Under-voltage
            1. 8.4.8.8.1.1 VSUP and VHSS Under-voltage
            2. 8.4.8.8.1.2 VCC1 Under-voltage
            3. 8.4.8.8.1.3 VCC2 and VEXCC Under-voltage
            4. 8.4.8.8.1.4 VCAN Under-voltage
          2. 8.4.8.8.2 VCC1, VCC2 and VEXCC Over-voltage
          3. 8.4.8.8.3 VCC1, VCC2 and VEXCC Short Circuit
        9. 8.4.8.9  Watchdog
          1. 8.4.8.9.1 Watchdog Error Counter and Action
          2. 8.4.8.9.2 Watchdog SPI Programming
            1. 8.4.8.9.2.1 Watchdog Configuration Registers Lock and Unlock
          3. 8.4.8.9.3 Watchdog Timing
          4. 8.4.8.9.4 Question and Answer Watchdog
            1. 8.4.8.9.4.1 WD Question and Answer Basic Information
            2. 8.4.8.9.4.2 Question and Answer Register and Settings
            3. 8.4.8.9.4.3 WD Question and Answer Value Generation
              1. 8.4.8.9.4.3.1 Answer Comparison
              2. 8.4.8.9.4.3.2 Sequence of the 2-bit Watchdog Answer Counter
            4. 8.4.8.9.4.4 Question and Answer WD Example
              1. 8.4.8.9.4.4.1 Example Configuration for Desired Behavior
              2. 8.4.8.9.4.4.2 Example of Performing a Question and Answer Sequence
        10. 8.4.8.10 Bus Fault Detection and Communication
    5. 8.5 Programming
      1. 8.5.1 SPI Communication
        1. 8.5.1.1 Cyclic Redundancy Check
        2. 8.5.1.2 Chip Select Not (nCS):
        3. 8.5.1.3 SPI Clock Input (SCK):
        4. 8.5.1.4 SPI Data Input (SDI):
        5. 8.5.1.5 SPI Data Output (SDO):
      2. 8.5.2 EEPROM
  10. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 CAN BUS Loading, Length and Number of Nodes
      2. 9.1.2 CAN Termination
        1. 9.1.2.1 Termination
      3. 9.1.3 Channel Expansion
        1. 9.1.3.1 Channel Expansion for LIN
        2. 9.1.3.2 Channel Expansion for CAN FD
      4. 9.1.4 Device Brownout information
      5. 9.1.5 Typical Application
        1. 9.1.5.1 Design Requirements
          1. 9.1.5.1.1 LTXD Dominant State Timeout Application Note
        2. 9.1.5.2 Detailed Design Procedures
          1. 9.1.5.2.1 CAN Detailed Design Procedure
          2. 9.1.5.2.2 LIN Detailed Design Procedures
        3. 9.1.5.3 Application Curves
    2. 9.2 Power Supply Recommendations
    3. 9.3 Layout
      1. 9.3.1 Layout Guidelines
      2. 9.3.2 Layout Example
  11. 10Registers
    1. 10.1 Registers
      1. 10.1.1  DEVICE_ID_y Register (Address = 00h + formula) [reset = xxh]
      2. 10.1.2  REV_ID Register (Address = 08h) [reset = 2Xh]
      3. 10.1.3  SPI_CONFIG Register (Address = 09h) [reset = 00h]
      4. 10.1.4  CRC_CNTL Register (Address = 0Ah) [reset = 00h]
      5. 10.1.5  CRC_POLY_SET (Address = 0Bh) [reset = 00h]
      6. 10.1.6  SBC_CONFIG (Address = 0Ch) [reset = 06h]
      7. 10.1.7  VREG_CONFIG1 (Address = 0Dh) [reset = 80h]
      8. 10.1.8  SBC_CONFIG1 Register (Address = 0Eh) [reset = 01h]
      9. 10.1.9  Scratch_Pad_SPI Register (Address = 0Fh) [reset = 00h]
      10. 10.1.10 CAN_CNTRL_1 Register (Address = 10h) [reset = 04h]
      11. 10.1.11 WAKE_PIN_CONFIG1 Register (Address = 11h) [reset = 00h]
      12. 10.1.12 WAKE_PIN_CONFIG2 Register (Address = 12h) [reset = 02h]
      13. 10.1.13 WD_CONFIG_1 Register (Address = 13h) [reset = 82h]
      14. 10.1.14 WD_CONFIG_2 Register (Address = 14h) [reset = 60h]
      15. 10.1.15 WD_INPUT_TRIG Register (Address = 15h) [reset = 00h]
      16. 10.1.16 WD_RST_PULSE Register (Address = 16h) [reset = 00h]
      17. 10.1.17 FSM_CONFIG Register (Address = 17h) [reset = 00h]
      18. 10.1.18 FSM_CNTR Register (Address = 18h) [reset = 00h]
      19. 10.1.19 DEVICE_CONFIG0 Register (Address = 19h) [reset = 10h]
      20. 10.1.20 DEVICE_CONFIG1 (Address = 1Ah) [reset = 00h]
      21. 10.1.21 DEVICE_CONFIG2 (Address = 1Bh) [reset = 00h]
      22. 10.1.22 SWE_TIMER (Address = 1Ch) [reset = 28h]
      23. 10.1.23 LIN_CNTL (Address = 1Dh) [reset = 20h]
      24. 10.1.24 HSS_CNTL (Address = 1Eh) [reset = 00h]
      25. 10.1.25 PWM1_CNTL1 (Address = 1Fh) [reset = 00h]
      26. 10.1.26 PWM1_CNTL2 (Address = 20h) [reset = 00h]
      27. 10.1.27 PWM1_CNTL3 (Address = 21h) [reset = 00h]
      28. 10.1.28 PWM2_CNTL1 (Address = 22h) [reset = 00h]
      29. 10.1.29 PWM2_CNTL2 (Address = 23h) [reset = 00h]
      30. 10.1.30 PWM2_CNTL3 (Address = 24h) [reset = 00h]
      31. 10.1.31 TIMER1_CONFIG (Address = 25h) [reset = 00h]
      32. 10.1.32 TIMER2_CONFIG (Address = 26h) [reset = 00h]
      33. 10.1.33 RSRT_CNTR (Address = 28h) [reset = 40h]
      34. 10.1.34 nRST_CNTL (Address = 29h) [reset = 2Ch]
      35. 10.1.35 WAKE_PIN_CONFIG3 Register (Address = 2Ah) [reset = E0h]
      36. 10.1.36 WAKE_PIN_CONFIG4 Register (Address = 2Bh) [reset = 22h]
      37. 10.1.37 WD_QA_CONFIG Register (Address = 2Dh) [reset = 0Ah]
      38. 10.1.38 WD_QA_ANSWER Register (Address = 2Eh) [reset = 00h]
      39. 10.1.39 WD_QA_QUESTION Register (Address = 2Fh) [reset = 3Ch]
      40. 10.1.40 SW_ID1 Register (Address = 30h) [reset = 00h]
      41. 10.1.41 SW_ID2 Register (Address = 31h) [reset = 00h]
      42. 10.1.42 SW_ID3 Register (Address = 32h) [reset = 00h]
      43. 10.1.43 SW_ID4 Register (Address = 33h) [reset = 00h]
      44. 10.1.44 SW_ID_MASK1 Register (Address = 34h) [reset = 00h]
      45. 10.1.45 SW_ID_MASK2 Register (Address = 35h) [reset = 00h]
      46. 10.1.46 SW_ID_MASK3 Register (Address = 36h) [reset = 00h]
      47. 10.1.47 SW_ID_MASK4 Register (Address = 37h) [reset = 00h]
      48. 10.1.48 SW_ID_MASK_DLC Register (Address = 38h) [reset = 00h]
      49. 10.1.49 DATA_y Register (Address = 39h + formula) [reset = 00h]
      50. 10.1.50 SW_RSVD_y Register (Address = 41h + formula) [reset = 00h]
      51. 10.1.51 SW_CONFIG_1 Register (Address = 44h) [reset = 50h]
      52. 10.1.52 SW_CONFIG_2 Register (Address = 45h) [reset = 00h]
      53. 10.1.53 SW_CONFIG_3 Register (Address = 46h) [reset = 1Fh]
      54. 10.1.54 SW_CONFIG_4 Register (Address = 47h) [reset = 00h]
      55. 10.1.55 SW_CONFIG_RSVD_y Register (Address = 48h + formula) [reset = 00h]
      56. 10.1.56 HSS_CNTL2 (Address = 4Dh) [reset = 00h]
      57. 10.1.57 EEPROM_CONFIG (Address = 4Eh) [reset = 00h]
      58. 10.1.58 HSS_CNTL3 (Address = 4Fh) [reset = 00h]
      59. 10.1.59 INT_GLOBAL Register (Address = 50h) [reset = 00h]
      60. 10.1.60 INT_1 Register (Address = 51h) [reset = 00h]
      61. 10.1.61 INT_2 Register (Address = 52h) [reset = 40h]
      62. 10.1.62 INT_3 Register (Address 53h) [reset = 00h]
      63. 10.1.63 INT_CANBUS_1 Register (Address = 54h) [reset = 00h]
      64. 10.1.64 INT_7 (Address = 55h) [reset = 00h]
      65. 10.1.65 INT_EN_1 Register (Address = 56h) [reset = FFh]
      66. 10.1.66 INT_EN_2 Register (Address = 57h) [reset = 7Eh]
      67. 10.1.67 INT_EN_3 Register (Address = 58h) [reset = FEh]
      68. 10.1.68 INT_EN_CANBUS_1 Register (Address = 59h) [reset = BFh]
      69. 10.1.69 INT_4 Register (Address = 5Ah) [reset = 00h]
      70. 10.1.70 INT_6 Register (Address 5Ch) [reset = 00h]
      71. 10.1.71 INT_EN_4 Register (Address = 5Eh) [reset = DFh]
      72. 10.1.72 INT_EN_6 Register (Address = 60h) [reset = FFh]
      73. 10.1.73 INT_EN_7 Register (Address = 62) [reset = FFh]
  12. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 CAN Transceiver Physical Layer Standards:
      2. 11.1.2 LIN Transceiver Physical Layer Standards
      3. 11.1.3 EMC Requirements:
      4. 11.1.4 Conformance Test Requirements:
      5. 11.1.5 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information
    1. 13.1 Mechanical Data

VEXCC Regulator

TCAN285x-Q1Can control an external PNP power transistor with β between 50 and 500 to support higher currents and wider voltage needs with the VEXCC output. The TCAN285x-Q1 can support 1.8V, 2.5V, 3.3V and 5V output. The voltage is selected using SPI register 8'h0D[2:0] and defaults to 1.8V. There are three monitors on VEXCC, under-voltage (UVEXCC), over-voltage (OVEXCC) and short to ground (VEXCCSC). The external PNP does not be turned on until register 8'h0D[5:4] is configured and is default off. When VEXCC is on and not in a fault state, register 8'h4F[3], VEXCC_STATUS, indicates this by being set to 1b. When load sharing is selected, the device automatically configures the voltage level to match the VCC1 voltage and follow the programming state of VCC1.

The shunt resistor, Rshunt, is between VSUP and VEXMON and serves two purposes depending upon configuration. When used as an stand-alone configuration, see Figure 8-6, Rshunt sets the current limit for the PNP FET. The value for Rshunt must be chosen based on the current limit requirement for the application. The value of this resistor is determined by the VSHUNTH threshold divided by the required current limit, meaning VSHUNTH/IVEXCC-LIM where IVEXCC-LIM is the required current limit value.

When configured for load sharing with VCC1, see Figure 8-7, the resistor Rshnut sets the ratio of current between VEXCC and VCC1. See Equation 1 and Equation 2 to determine how to calculate the Rshunt value.

If the TCAN285x-Q1 is not already programmed for VEXCC load sharing with VCC1 using end-of-line programming, the device can be programmed for load sharing using the following sequence of steps:

  1. Power-up the device with VCC1 shorted to EXVCC on the board; the device powers-up into Standby mode
  2. Set VEXCC voltage configuration register, 8'h0D[2:0], to the correct voltage setting. This must be the same as VCC1 setting (3.3V or 5V only)
  3. Set the VEXT_CFG, VEXCC configuration register, 8'h0D[5:4] to match the VCC1_CFG setting
  4. Wait 5ms for output to settle, read VEXCC_STATUS, 8'h4F[3], to confirm VEXCC is in regulation
  5. Enable Load Sharing for VEXCC with register 8'h0D[2:0] = 100b
  6. If the Load Sharing configuration is not saved to EEPROM and the device experiences POR event, repeat the steps 1-5.
Equation 1. Ratio=(IVEXCCIVCC1)
Equation 2. Rshunt=8.824Ratio-(1+RatioRatio×0.8Iload)
TCAN2855-Q1 TCAN2857-Q1 Stand-alone External PNP ExampleFigure 8-6 Stand-alone External PNP Example
Note:

1. A series resistance of RPROT = 100Ω is recommended when supplying ECU-external loads for EMC robustness

TCAN2855-Q1 TCAN2857-Q1 External PNP Example With Load SharingFigure 8-7 External PNP Example With Load Sharing
TCAN2855-Q1 TCAN2857-Q1 VEXCC versus IVEXCTRL Timing DiagramFigure 8-8 VEXCC versus IVEXCTRL Timing Diagram
Note:
  • The external PNP transistor power handling capabilities are application specific and must therefore be designed according to the selected PNP device along with the PCB properties to prevent thermal damage as the SBC is not able to make sure the thermal protection of the external PNP transistor.
  • For limiting current through the external PNP transistor, connect VEXMON pin to the same power rail that connects to VSUP pin of the device using Rshunt as shown in Figure 8-6.
  • If the external PNP collector is being connected to a different voltage rail, the device is not able to provide current limit capability. To avoid issues, the current limit must be disabled by using SBC_CONFIG register 8'h0C[6] VEXCC_ILIM_DIS = 1b. Disabling the current limit does not disable over-voltage, under-voltage, or short circuit detection.