SLUSG51A October   2025  – August 2026 BQ25692-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Device Power-On-Reset
      2. 6.3.2  Battery Only Power Up State
      3. 6.3.3  Device HIZ State
      4. 6.3.4  Power Up REGN LDO
      5. 6.3.5  Default VINDPM Setting
      6. 6.3.6  Default Charge Profile Setting With CELL, ICHG and VCHG Pins
      7. 6.3.7  Buck-Boost Converter Operation
        1. 6.3.7.1 Pulse Frequency Modulation (PFM)
        2. 6.3.7.2 Switching Frequency and Dithering Feature
      8. 6.3.8  Forward (Sink) Operation
        1. 6.3.8.1 Power Path Management
          1. 6.3.8.1.1 Dynamic Power Management
            1. 6.3.8.1.1.1 ILIM_HIZ Pin
            2. 6.3.8.1.1.2 Input Current Optimizer (ICO)
          2. 6.3.8.1.2 Maximum Power Point Tracking for Small PV Panel
        2. 6.3.8.2 Battery Charging Management
          1. 6.3.8.2.1 Battery Detection
          2. 6.3.8.2.2 Autonomous Charging Cycle
          3. 6.3.8.2.3 Battery Charging Profile
          4. 6.3.8.2.4 Charging Termination
          5. 6.3.8.2.5 Charging Safety Timer
          6. 6.3.8.2.6 CV Timer
          7. 6.3.8.2.7 Thermistor Qualification
            1. 6.3.8.2.7.1 JEITA Guideline Compliance in Charge Mode
            2. 6.3.8.2.7.2 Cold/Hot Temperature Window in Reverse Mode
        3. 6.3.8.3 Bypass Mode
      9. 6.3.9  Reverse (Source) Mode (USB On-The-Go)
        1. 6.3.9.1 Reverse (Source) Mode Operation
        2. 6.3.9.2 Backup Power Supply Mode
        3. 6.3.9.3 Reverse Bypass Mode
      10. 6.3.10 Status Outputs (STAT and INT)
        1. 6.3.10.1 Power Good Indicator (PG_STAT)
        2. 6.3.10.2 Charging Status Indicator (STAT Pin)
        3. 6.3.10.3 Interrupt to Host ( INT)
      11. 6.3.11 Serial Interface
        1. 6.3.11.1 Data Validity
        2. 6.3.11.2 START and STOP Conditions
        3. 6.3.11.3 Byte Format
        4. 6.3.11.4 Acknowledge (ACK) and Not Acknowledge (NACK)
        5. 6.3.11.5 Target Address and Data Direction Bit
        6. 6.3.11.6 Single Write and Read
        7. 6.3.11.7 Multi-Write and Multi-Read
    4. 6.4 Device Functional Modes
      1. 6.4.1 Host Mode and Default Mode
      2. 6.4.2 Register Bit Reset
  8. 7 Register Map
    1. 7.1 BQ25692Q1 Registers
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application Design Example
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Inductor Selection
        2. 8.2.2.2 Capacitors
        3. 8.2.2.3 Buck Mode Input (VIN) Capacitor
        4. 8.2.2.4 Boost Mode Output (VOUT) Capacitor
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Third-Party Products Disclaimer
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

6.3.11.3 Byte Format

Verify that every byte on the SDA line is 8 bits long. The number of bytes transmitted per transfer is unrestricted. An ACKNOWLEDGE (ACK) bit must follow each byte. Data is transferred with the Most Significant Bit (MSB) first. If the target device cannot receive or transmit another complete byte of data until the target device performs some other function, the target device can hold the SCL line low to force the controller into a wait state (clock stretching). Data transfer then continues when the target device is ready for another byte of data and releases the SCL line.

BQ25692-Q1 Data Transfer on the I2C Bus Figure 6-14 Data Transfer on the I2C Bus