SLUSG59 February   2026 BQ27Z855

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configurations and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Supply Current
    5. 5.5  1.8V LDO Regulator (REG18)
    6. 5.6  Low Frequency Oscillator (LFO)
    7. 5.7  High Frequency Oscillator (HFO)
    8. 5.8  PACK Clamp (PACK_CLAMP)
    9. 5.9  Analog-to-Digital Converter (VADC)
    10. 5.10 Coulomb Counter (CCADC)
    11. 5.11 Coulomb Counter Digital Filter (CC1)
    12. 5.12 Current Measurement Digital Filter (CC2)
    13. 5.13 Charge Current Measurement Digital Filter (CC3)
    14. 5.14 Wake-up Comparator (I-WAKE)
    15. 5.15 Internal Temperature Sensor (INT_TEMP)
    16. 5.16 Thermistor Measurement Support
    17. 5.17 Hardware-based Protection (SCOMP) Thresholds (OVP, UVP, OCC, OCD, SCD)
    18. 5.18 Hardware-based Protections (SCOMP) Timing (OVP, UVP, OCC, OCD, SCD)
    19. 5.19 Current Limiter
    20. 5.20 CHG, DSG NFET Drivers
    21. 5.21 Zero-volt Charging (ZVCHG)
    22. 5.22 General Purpose Input-Outputs (INT)
    23. 5.23 I2C Interface I/O (SDA, SCL)
    24. 5.24 I2C Interface Timing
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  BQ27Z855 Processor
      2. 6.3.2  Battery Parameter Measurements
        1. 6.3.2.1 Analog-to-Digital Converter (VADC)
        2. 6.3.2.2 VADC Multiplexer
        3. 6.3.2.3 Coulomb Counter (CCADC) and Digital Filter (CC1)
        4. 6.3.2.4 Internal Temperature Sensor (INT_TEMP)
        5. 6.3.2.5 External Temperature Sensor Support
      3. 6.3.3  Power Supply Control
      4. 6.3.4  ENAB Pin
      5. 6.3.5  I2C Bus Communication Interface
      6. 6.3.6  Low Frequency Oscillator (LFO)
      7. 6.3.7  High Frequency Oscillator (HFO)
      8. 6.3.8  Real Time Clock (RTC)
      9. 6.3.9  1.8V Low Dropout Regulator (REG18)
      10. 6.3.10 FET Drivers (CHG, DSG)
        1. 6.3.10.1 Charge (CHG) FET Driver
        2. 6.3.10.2 Discharge (DSG) FET Driver
      11. 6.3.11 Zero-volt Charging (ZVCHG)
      12. 6.3.12 Integrated Protections
        1. 6.3.12.1 Hardware-based Protections
          1. 6.3.12.1.1 Overvoltage Protection (OVP)
          2. 6.3.12.1.2 Undervoltage Protection (UVP)
          3. 6.3.12.1.3 Overcurrent in Charge Protection (OCC)
          4. 6.3.12.1.4 Overcurrent in Discharge Protection (OCD)
          5. 6.3.12.1.5 Short Circuit Current in Discharge Protection (SCD)
          6. 6.3.12.1.6 Wake-up Comparator (I-WAKE)
        2. 6.3.12.2 Firmware-based Protections
          1. 6.3.12.2.1 Primary Level Protection Features
          2. 6.3.12.2.2 Secondary Level Protection Features
      13. 6.3.13 Gas Gauging
      14. 6.3.14 Advanced Battery Algorithms
        1. 6.3.14.1 Si-anode Chemistry Support
        2. 6.3.14.2 Internal Short Indication (ISI)
        3. 6.3.14.3 Battery Swelling Detection (BSD)
      15. 6.3.15 Integrated Current Limiter and Charge Control Features
        1. 6.3.15.1 Integrated Current Limiter
          1. 6.3.15.1.1 CHG FET State Machine
          2. 6.3.15.1.2 Linear Mode
            1. 6.3.15.1.2.1 Battery Charging Process
            2. 6.3.15.1.2.2 Zero-volt Charge (ZVCHG)
            3. 6.3.15.1.2.3 Precharge (PCHG)
            4. 6.3.15.1.2.4 Fast Charge (CC)
            5. 6.3.15.1.2.5 Taper-charge (CV)
            6. 6.3.15.1.2.6 Charge Termination (VCT)
            7. 6.3.15.1.2.7 Step-charging Profile Support
          3. 6.3.15.1.3 MINSYS Mode
          4. 6.3.15.1.4 Battery Supplement Mode
        2. 6.3.15.2 Interaction with a Smart Charger
      16. 6.3.16 Ideal Diode Mode
      17. 6.3.17 Lifetime Data Logging Features
      18. 6.3.18 Authentication
        1. 6.3.18.1 ECC ECDSA Authentication
        2. 6.3.18.2 SHA-256 Authentication
      19. 6.3.19 Over the Air (OTA) Field Updater
      20. 6.3.20 Configuration
        1. 6.3.20.1 Cell Voltage Measurements
        2. 6.3.20.2 Coulomb Counting
        3. 6.3.20.3 Temperature Measurements
    4. 6.4 Device Functional Modes
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application Schematics
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1 High-Current Path
          1. 7.2.2.1.1 Protection FETs
          2. 7.2.2.1.2 Battery Cell Connections
          3. 7.2.2.1.3 Sense Resistor
          4. 7.2.2.1.4 ESD Mitigation
        2. 7.2.2.2 Gas Gauge Circuit
          1. 7.2.2.2.1 Cell Voltage Measurement Interface
          2. 7.2.2.2.2 Coulomb Counter Interface
          3. 7.2.2.2.3 Temperature Measurement
          4. 7.2.2.2.4 1.8V Low Dropout Regulator (REG18)
          5. 7.2.2.2.5 I2C Communication (SDA, SCL)
          6. 7.2.2.2.6 Interrupt to Host Interface (INT)
        3. 7.2.2.3 Current Limiter Circuit
          1. 7.2.2.3.1 Protection FETs and Compatibility with BQ27Z855
          2. 7.2.2.3.2 CP Control Logic and Capacitor
          3. 7.2.2.3.3 Voltage-based Feedback Interface
          4. 7.2.2.3.4 Current-based Feedback Interface
            1. 7.2.2.3.4.1 Sense Resistor Impact on Current-based Feedback
            2. 7.2.2.3.4.2 Sense Resistor Impact on CHG FET State Transitions
          5. 7.2.2.3.5 BAT-PACK Dedicated Voltage Comparator (DCOMP)
            1. 7.2.2.3.5.1 Impact of Sense Resistor Configuration on DCOMP Sensing
          6. 7.2.2.3.6 System-level Recommendations
        4. 7.2.2.4 Co-design with BQ27Z746 and BQ27Z758
          1. 7.2.2.4.1 Footprint Compatibility and Equivalent Pins
          2. 7.2.2.4.2 Co-layout Example
  9. 8 Power Supply Recommendations
  10. 9 Layout
    1. 9.1 Layout Guidelines
  11. 10Device and Documentation Support
    1. 10.1 Third-Party Products Disclaimer
    2. 10.2 Documentation Support
      1. 10.2.1 Related Documentation
    3. 10.3 Trademarks
    4. 10.4 Electrostatic Discharge Caution
    5. 10.5 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1.     PACKAGE OPTION ADDENDUM
    2. 12.1 Tape and Reel Information
    3. 12.2 Mechanical Data

6.3.13 Gas Gauging

The BQ27Z855 uses the Dynamic Z-Track™ algorithm to measure and calculate the available capacity in battery cells. The BQ27Z855 accumulates a measure of charge and discharge currents and compensates the charge current measurement for the temperature, state-of-charge, and relaxation time constants of the battery. The BQ27Z855 estimates self-discharge of the battery and also adjusts the self-discharge estimation based on temperature.

For more information on the theory and implementation of the Dynamic Z-Track™ algorithm, refer to the following Application Note on Dynamic Z-Track™: Dynamic Z-Track™ Technology: An Advanced Battery Gauging Algorithm for Dynamic Load Applications.