SLVSJC6 December   2025 TPS544B27W

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Switching Characteristics
    8. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Operating Frequency and Mode
      2. 6.3.2 Setting the Output Voltage
      3. 6.3.3 DC Load Line
      4. 6.3.4 Fault Management
      5. 6.3.5 Current Sense and Positive Overcurrent Protection
      6. 6.3.6 Negative Overcurrent Limit
      7. 6.3.7 Zero-Crossing Detection
      8. 6.3.8 Overtemperature Protection
      9. 6.3.9 PMBus® Interface
        1. 6.3.9.1 Setting the PMBus® Address
        2. 6.3.9.2 SMBus Alert Response Address
    4. 6.4 Device Functional Modes
      1. 6.4.1 Forced Continuous-Conduction Mode
      2. 6.4.2 DCM Light Load Operation
    5. 6.5 Programming
      1. 6.5.1 PMBus® Command NVM Defaults
  8. 7 Register Maps
    1. 7.1 PMBus® Transaction Types
    2. 7.2 Conventions for Documenting Block Commands
    3. 7.3 PMBus Commands
      1. 7.3.1  OPERATION (Address = 01h)
      2. 7.3.2  ON_OFF_CONFIG (Address = 02h)
      3. 7.3.3  CLEAR_FAULTS (Address = 03h)
      4.      42
      5. 7.3.4  PASSKEY (Address = 0Eh)
      6. 7.3.5  WRITE_PROTECT (Address = 10h)
      7. 7.3.6  STORE_USER_ALL (Address = 15h)
      8.      46
      9. 7.3.7  RESTORE_USER_ALL (Address = 16h)
      10.      48
      11. 7.3.8  CAPABILITY (Address = 19h)
      12. 7.3.9  SMBALERT_MASK (Address = 1Bh)
      13.      51
      14. 7.3.10 SMBALERT_MASK Registers
        1. 7.3.10.1  ALERT_MASK_BYTE (Address = 78h) [Reset = C8h]
        2. 7.3.10.2  ALERT_MASK_WORD (Address = 79h) [Reset = 0Dh]
        3. 7.3.10.3  ALERT_MASK_VOUT (Address = 7Ah) [Reset = XXh]
        4. 7.3.10.4  ALERT_MASK_IOUT (Address = 7Bh) [Reset = XFh]
        5. 7.3.10.5  ALERT_MASK_INPUT (Address = 7Ch) [Reset = XXh]
        6. 7.3.10.6  ALERT_MASK_TEMPERATURE (Address = 7Dh) [Reset = XFh]
        7. 7.3.10.7  ALERT_MASK_CML (Address = 7Eh) [Reset = XXh]
        8. 7.3.10.8  ALERT_MASK_OTHER (Address = 7Fh) [Reset = XFh]
        9. 7.3.10.9  ALERT_MASK_MFR_SPECIFIC (Address = 80h) [Reset = XXh]
        10. 7.3.10.10 ALERT_MASK_PULSE_CATCHER (Address = CEh) [Reset = FXh]
      15. 7.3.11 VOUT_MODE (Address = 20h)
      16. 7.3.12 VOUT_COMMAND (Address = 21h)
      17. 7.3.13 VOUT_TRIM (Address = 22h)
      18. 7.3.14 VOUT_MAX (Address = 24h)
      19.      67
      20. 7.3.15 VOUT_MARGIN_HIGH (Address = 25h)
      21.      69
      22. 7.3.16 VOUT_MARGIN_LOW (Address = 26h)
      23.      71
      24. 7.3.17 VOUT_TRANSITION_RATE (Address = 27h)
      25.      73
      26. 7.3.18 VOUT_DROOP (Address = 28h)
      27. 7.3.19 VOUT_SCALE_LOOP (Address = 29h)
      28.      76
      29. 7.3.20 FREQUENCY_SWITCH (Address = 33h)
      30.      78
      31. 7.3.21 VIN_ON (Address = 35h)
      32.      80
      33. 7.3.22 VIN_OFF (Address = 36h)
      34.      82
      35. 7.3.23 VOUT_OV_FAULT_LIMIT (Address = 40h)
      36.      84
      37. 7.3.24 VOUT_OV_FAULT_RESPONSE (Address = 41h)
      38. 7.3.25 VOUT_OV_WARN_LIMIT (Address = 42h)
      39.      87
      40. 7.3.26 VOUT_UV_WARN_LIMIT (Address = 43h)
      41.      89
      42. 7.3.27 VOUT_UV_FAULT_LIMIT (Address = 44h)
      43.      91
      44. 7.3.28 VOUT_UV_FAULT_RESPONSE (Address = 45h)
      45. 7.3.29 IOUT_OC_FAULT_LIMIT (Address = 46h)
      46.      94
      47. 7.3.30 IOUT_OC_FAULT_RESPONSE (Address = 47h)
      48. 7.3.31 IOUT_OC_WARN_LIMIT (Address = 4Ah)
      49. 7.3.32 OT_FAULT_LIMIT (Address = 4Fh)
      50.      98
      51. 7.3.33 OT_FAULT_RESPONSE (Address = 50h)
      52. 7.3.34 OT_WARN_LIMIT (Address = 51h)
      53.      101
      54. 7.3.35 VIN_OV_FAULT_LIMIT (Address = 55h)
      55.      103
      56. 7.3.36 TON_DELAY (Address = 60h)
      57.      105
      58. 7.3.37 TON_RISE (Address = 61h)
      59. 7.3.38 TOFF_DELAY (Address = 64h)
      60. 7.3.39 TOFF_FALL (Address = 65h)
      61. 7.3.40 PIN_OP_WARN_LIMIT (Address = 6Bh)
      62.      110
      63.      111
      64.      112
      65. 7.3.41 STATUS_BYTE (Address = 78h)
      66. 7.3.42 STATUS_WORD (Address = 79h)
      67. 7.3.43 STATUS_VOUT (Address = 7Ah)
      68. 7.3.44 STATUS_IOUT (Address = 7Bh)
      69. 7.3.45 STATUS_INPUT (Address = 7Ch)
      70. 7.3.46 STATUS_TEMPERATURE (Address = 7Dh)
      71. 7.3.47 STATUS_CML (Address = 7Eh)
      72. 7.3.48 STATUS_OTHER (Address = 7Fh)
      73. 7.3.49 STATUS_MFR_SPECIFIC (Address = 80h)
      74. 7.3.50 READ_VIN (Address = 88h)
      75. 7.3.51 READ_IIN (Address = 89h)
      76. 7.3.52 READ_VOUT (Address = 8Bh)
      77. 7.3.53 READ_IOUT (Address = 8Ch)
      78. 7.3.54 READ_TEMPERATURE_1 (Address = 8Dh)
      79. 7.3.55 READ_PIN (Address = 97h)
      80. 7.3.56 PMBUS_REVISION (Address = 98h)
      81. 7.3.57 MFR_ID (Address = 99h)
      82. 7.3.58 MFR_MODEL (Address = 9Ah)
      83.      131
      84. 7.3.59 MFR_REVISION (Address = 9Bh)
      85. 7.3.60 IC_DEVICE_ID (Address = ADh)
      86. 7.3.61 IC_DEVICE_REV (Address = AEh)
      87.      135
      88. 7.3.62 EXTENDED_WRITE_PROTECT (Address = C7h)
      89. 7.3.63 NVM_PATCH_SPACE (Address = CDh)
      90. 7.3.64 CLOUD_OPTIONS (Address = CFh)
      91. 7.3.65 SYS_CFG_USER1 (Address = D0h)
      92.      140
      93. 7.3.66 SVID_ADDR_CFG_USER (Address = D1h)
      94. 7.3.67 PMBUS_ADDR (Address = D2h)
      95. 7.3.68 IMON_CAL (Address = D4h)
      96. 7.3.69 COMP (Address = D5h)
      97.      145
      98. 7.3.70 VBOOT_DCLL (Address = D6h)
      99. 7.3.71 VBOOT_OFFSET_1 (Address = D7h)
      100. 7.3.72 IIN_CAL (Address = D8h)
      101. 7.3.73 SVID_IMAX (Address = DAh)
      102.      150
      103. 7.3.74 SVID_EXT_CAPABILITY_VIDOMAX (Address = DBh)
      104. 7.3.75 FUSION_ID0 (Address = FCh)
      105. 7.3.76 FUSION_ID1 (Address = FDh)
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Application
      2. 8.2.2 Design Requirements
      3. 8.2.3 Detailed Design Procedure
        1. 8.2.3.1 Inductor Selection
        2. 8.2.3.2 Input Capacitor Selection
        3. 8.2.3.3 Output Capacitor Selection
        4. 8.2.3.4 VCC/VDRV Bypass Capacitor
        5. 8.2.3.5 BOOT Capacitor Selection
        6. 8.2.3.6 RSENSE Selection
        7. 8.2.3.7 I_IN_P and I_IN_M Capacitor Selection
        8. 8.2.3.8 VRRDY Pullup Resistor Selection
        9. 8.2.3.9 PMBus® Address Resistor Selection
      4. 8.2.4 Application Curves
        1. 8.2.4.1 Thermal Performance
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Receiving Notification of Documentation Updates
    2. 9.2 Support Resources
    3. 9.3 Trademarks
    4. 9.4 Electrostatic Discharge Caution
    5. 9.5 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

8.2.3.7 I_IN_P and I_IN_M Capacitor Selection

Use a 100pF/25V/0402 ceramic capacitor referenced to PGND on both the I_IN_P Pin 3 and I_IN_M Pin 4. Place another 100pF/25V/0402 ceramic capacitor between Pin 3 and Pin 4. These decoupling capacitors minimize the impact from switching noise on the 12V bus and thus help the device to achieve high accuracy on input current reporting.