SLVSJC6 December   2025 TPS544B27W

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Switching Characteristics
    8. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Operating Frequency and Mode
      2. 6.3.2 Setting the Output Voltage
      3. 6.3.3 DC Load Line
      4. 6.3.4 Fault Management
      5. 6.3.5 Current Sense and Positive Overcurrent Protection
      6. 6.3.6 Negative Overcurrent Limit
      7. 6.3.7 Zero-Crossing Detection
      8. 6.3.8 Overtemperature Protection
      9. 6.3.9 PMBus® Interface
        1. 6.3.9.1 Setting the PMBus® Address
        2. 6.3.9.2 SMBus Alert Response Address
    4. 6.4 Device Functional Modes
      1. 6.4.1 Forced Continuous-Conduction Mode
      2. 6.4.2 DCM Light Load Operation
    5. 6.5 Programming
      1. 6.5.1 PMBus® Command NVM Defaults
  8. 7 Register Maps
    1. 7.1 PMBus® Transaction Types
    2. 7.2 Conventions for Documenting Block Commands
    3. 7.3 PMBus Commands
      1. 7.3.1  OPERATION (Address = 01h)
      2. 7.3.2  ON_OFF_CONFIG (Address = 02h)
      3. 7.3.3  CLEAR_FAULTS (Address = 03h)
      4.      42
      5. 7.3.4  PASSKEY (Address = 0Eh)
      6. 7.3.5  WRITE_PROTECT (Address = 10h)
      7. 7.3.6  STORE_USER_ALL (Address = 15h)
      8.      46
      9. 7.3.7  RESTORE_USER_ALL (Address = 16h)
      10.      48
      11. 7.3.8  CAPABILITY (Address = 19h)
      12. 7.3.9  SMBALERT_MASK (Address = 1Bh)
      13.      51
      14. 7.3.10 SMBALERT_MASK Registers
        1. 7.3.10.1  ALERT_MASK_BYTE (Address = 78h) [Reset = C8h]
        2. 7.3.10.2  ALERT_MASK_WORD (Address = 79h) [Reset = 0Dh]
        3. 7.3.10.3  ALERT_MASK_VOUT (Address = 7Ah) [Reset = XXh]
        4. 7.3.10.4  ALERT_MASK_IOUT (Address = 7Bh) [Reset = XFh]
        5. 7.3.10.5  ALERT_MASK_INPUT (Address = 7Ch) [Reset = XXh]
        6. 7.3.10.6  ALERT_MASK_TEMPERATURE (Address = 7Dh) [Reset = XFh]
        7. 7.3.10.7  ALERT_MASK_CML (Address = 7Eh) [Reset = XXh]
        8. 7.3.10.8  ALERT_MASK_OTHER (Address = 7Fh) [Reset = XFh]
        9. 7.3.10.9  ALERT_MASK_MFR_SPECIFIC (Address = 80h) [Reset = XXh]
        10. 7.3.10.10 ALERT_MASK_PULSE_CATCHER (Address = CEh) [Reset = FXh]
      15. 7.3.11 VOUT_MODE (Address = 20h)
      16. 7.3.12 VOUT_COMMAND (Address = 21h)
      17. 7.3.13 VOUT_TRIM (Address = 22h)
      18. 7.3.14 VOUT_MAX (Address = 24h)
      19.      67
      20. 7.3.15 VOUT_MARGIN_HIGH (Address = 25h)
      21.      69
      22. 7.3.16 VOUT_MARGIN_LOW (Address = 26h)
      23.      71
      24. 7.3.17 VOUT_TRANSITION_RATE (Address = 27h)
      25.      73
      26. 7.3.18 VOUT_DROOP (Address = 28h)
      27. 7.3.19 VOUT_SCALE_LOOP (Address = 29h)
      28.      76
      29. 7.3.20 FREQUENCY_SWITCH (Address = 33h)
      30.      78
      31. 7.3.21 VIN_ON (Address = 35h)
      32.      80
      33. 7.3.22 VIN_OFF (Address = 36h)
      34.      82
      35. 7.3.23 VOUT_OV_FAULT_LIMIT (Address = 40h)
      36.      84
      37. 7.3.24 VOUT_OV_FAULT_RESPONSE (Address = 41h)
      38. 7.3.25 VOUT_OV_WARN_LIMIT (Address = 42h)
      39.      87
      40. 7.3.26 VOUT_UV_WARN_LIMIT (Address = 43h)
      41.      89
      42. 7.3.27 VOUT_UV_FAULT_LIMIT (Address = 44h)
      43.      91
      44. 7.3.28 VOUT_UV_FAULT_RESPONSE (Address = 45h)
      45. 7.3.29 IOUT_OC_FAULT_LIMIT (Address = 46h)
      46.      94
      47. 7.3.30 IOUT_OC_FAULT_RESPONSE (Address = 47h)
      48. 7.3.31 IOUT_OC_WARN_LIMIT (Address = 4Ah)
      49. 7.3.32 OT_FAULT_LIMIT (Address = 4Fh)
      50.      98
      51. 7.3.33 OT_FAULT_RESPONSE (Address = 50h)
      52. 7.3.34 OT_WARN_LIMIT (Address = 51h)
      53.      101
      54. 7.3.35 VIN_OV_FAULT_LIMIT (Address = 55h)
      55.      103
      56. 7.3.36 TON_DELAY (Address = 60h)
      57.      105
      58. 7.3.37 TON_RISE (Address = 61h)
      59. 7.3.38 TOFF_DELAY (Address = 64h)
      60. 7.3.39 TOFF_FALL (Address = 65h)
      61. 7.3.40 PIN_OP_WARN_LIMIT (Address = 6Bh)
      62.      110
      63.      111
      64.      112
      65. 7.3.41 STATUS_BYTE (Address = 78h)
      66. 7.3.42 STATUS_WORD (Address = 79h)
      67. 7.3.43 STATUS_VOUT (Address = 7Ah)
      68. 7.3.44 STATUS_IOUT (Address = 7Bh)
      69. 7.3.45 STATUS_INPUT (Address = 7Ch)
      70. 7.3.46 STATUS_TEMPERATURE (Address = 7Dh)
      71. 7.3.47 STATUS_CML (Address = 7Eh)
      72. 7.3.48 STATUS_OTHER (Address = 7Fh)
      73. 7.3.49 STATUS_MFR_SPECIFIC (Address = 80h)
      74. 7.3.50 READ_VIN (Address = 88h)
      75. 7.3.51 READ_IIN (Address = 89h)
      76. 7.3.52 READ_VOUT (Address = 8Bh)
      77. 7.3.53 READ_IOUT (Address = 8Ch)
      78. 7.3.54 READ_TEMPERATURE_1 (Address = 8Dh)
      79. 7.3.55 READ_PIN (Address = 97h)
      80. 7.3.56 PMBUS_REVISION (Address = 98h)
      81. 7.3.57 MFR_ID (Address = 99h)
      82. 7.3.58 MFR_MODEL (Address = 9Ah)
      83.      131
      84. 7.3.59 MFR_REVISION (Address = 9Bh)
      85. 7.3.60 IC_DEVICE_ID (Address = ADh)
      86. 7.3.61 IC_DEVICE_REV (Address = AEh)
      87.      135
      88. 7.3.62 EXTENDED_WRITE_PROTECT (Address = C7h)
      89. 7.3.63 NVM_PATCH_SPACE (Address = CDh)
      90. 7.3.64 CLOUD_OPTIONS (Address = CFh)
      91. 7.3.65 SYS_CFG_USER1 (Address = D0h)
      92.      140
      93. 7.3.66 SVID_ADDR_CFG_USER (Address = D1h)
      94. 7.3.67 PMBUS_ADDR (Address = D2h)
      95. 7.3.68 IMON_CAL (Address = D4h)
      96. 7.3.69 COMP (Address = D5h)
      97.      145
      98. 7.3.70 VBOOT_DCLL (Address = D6h)
      99. 7.3.71 VBOOT_OFFSET_1 (Address = D7h)
      100. 7.3.72 IIN_CAL (Address = D8h)
      101. 7.3.73 SVID_IMAX (Address = DAh)
      102.      150
      103. 7.3.74 SVID_EXT_CAPABILITY_VIDOMAX (Address = DBh)
      104. 7.3.75 FUSION_ID0 (Address = FCh)
      105. 7.3.76 FUSION_ID1 (Address = FDh)
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Application
      2. 8.2.2 Design Requirements
      3. 8.2.3 Detailed Design Procedure
        1. 8.2.3.1 Inductor Selection
        2. 8.2.3.2 Input Capacitor Selection
        3. 8.2.3.3 Output Capacitor Selection
        4. 8.2.3.4 VCC/VDRV Bypass Capacitor
        5. 8.2.3.5 BOOT Capacitor Selection
        6. 8.2.3.6 RSENSE Selection
        7. 8.2.3.7 I_IN_P and I_IN_M Capacitor Selection
        8. 8.2.3.8 VRRDY Pullup Resistor Selection
        9. 8.2.3.9 PMBus® Address Resistor Selection
      4. 8.2.4 Application Curves
        1. 8.2.4.1 Thermal Performance
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Receiving Notification of Documentation Updates
    2. 9.2 Support Resources
    3. 9.3 Trademarks
    4. 9.4 Electrostatic Discharge Caution
    5. 9.5 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

7.3.1 OPERATION (Address = 01h)

OPERATION is shown in Figure 7-2 and described in Table 7-3.

Return to the Summary Table.

Write Transaction: Write Byte
Read Transaction: Read Byte
Data Format: Unsigned Binary (1 byte)
NVM Back-up: No
Updates: On-the-fly The OPERATION command is used to turn the device output on or off, in conjunction with the input from the EN pin, according to the configuration of the ON_OFF_CONFIG command. It is also used to set the output voltage to the upper or lower MARGIN levels, and select soft-stop when turned off through OPERATION. Data Validity: Attempts to write 0b11XX, 0b0100, 0b0111, 0b1000, 0b1011 to MARGIN[3:0] or to write 1 to OPERATION[1] are considered as invalid data or unsupported data (ivd) and the device responds as described in the IVD bit in STATUS_CML.

Figure 7-2 OPERATION
76543210
ONOFFMARGIN[3:0]OPERATION[1:0]
R/W-0hR/W-0hR/W-1hR-0h
Table 7-3 OPERATION Field Descriptions
BitFieldTypeResetDescription
7ONR/W0h Turn the device output on or off when the ON_OFF_CONFIG command is configured with its CMD bit high. There can be several other requirements that must be satisfied before the power conversion can begin. The input voltages must be above their UVLO thresholds and, if the CPR bit in ON_OFF_CONFIG is high, the enable pin must be high.
  • 0h = The device output is off
  • 1h = The device output is on
6OFFR/W0h Sets the turn-off behavior when commanding the device output off via OPERATION[7] (the ON bit transitions from 1 to 0) and when the ON_OFF_CONFIG command is configured with its CMD bit high. If the ON bit is 1, then the OFF bit is ignored.
  • 0h = Immediately turn the device output off forcing the power stage to a high-Z state, not honoring the programmed TOFF_DELAY and programmed TOFF_FALL, when commanded off via OPERATION[7].
  • 1h = Soft off. Use the programmed turn-off delay in TOFF_DELAY and ramp down in TOFF_FALL when commanded off via OPERATION[7].
5:2MARGIN[3:0]R/W1h Sets the margin state, independent of the OPERATION[7] bit value. Values other than those listed below are invalid/unsupported data. If margin is off, the output voltage source is VOUT_COMMAND and OV/UV faults behave normally as programmed in their respective fault response registers.
  • 0h = Margin off and faults behave as programmed.
  • 1h = Margin off and faults behave as programmed.
  • 2h = Margin off and faults behave as programmed.
  • 3h = Margin off and faults behave as programmed.
  • 5h = Margin low (Ignore fault). Output voltage target uses VOUT_MARGIN_LOW. UV faults are ignored and do not trigger shut-down, but will trigger STATUS updates.
  • 6h = Margin low (Act on fault). Output voltage target uses VOUT_MARGIN_LOW. OV/UV faults trigger per their respective fault response settings.
  • 9h = Margin high (Ignore fault). Output voltage target uses VOUT_MARGIN_HIGH. OV faults are ignored and do not trigger shut-down, but will trigger STATUS updates.
  • Ah = Margin high (Act on fault). Output voltage target uses VOUT_MARGIN_HIGH. OV/UV faults trigger per their respective fault response settings.
1:0OPERATION[1:0]R0h Reserved.