AWRL6432
- FMCW Transceiver
- Integrated PLL, transmitter, receiver, baseband and ADC
- 57GHz - 64GHz coverage with 7GHz continuous bandwidth
- 3 receive channels and 2 transmit channels
- Range typically up to 25m
- 11dBm typical output power per Tx
- 11dB Typical noise figure
- -89dBc/Hz typical phase noise at 1MHz
- FMCW operation
- 5MHz IF bandwidth, real-only Rx channels
- Ultra-accurate chirp engine based on fractional-N PLL
- Per transmitter binary phase shifter
- Processing elements
- Arm M4F core with single precision FPU (160MHz)
- TI Radar Hardware Accelerator (HWA 1.2) for FFT, log magnitude, and CFAR operations (80MHz)
- Supports multiple low-power
modes
- Idle mode and deep sleep mode
- Power management
- 1.8V and 3.3V IO support
- Built-in LDO network for enhanced PSRR
- BOM-Optimized and Power-Optimized modes
- One or two power rails for 1.8V IO mode, two or three power rails for 3.3V IO mode
- Built-in calibration and
self-test
- Built-in Firmware (ROM)
- Self-Contained on chip calibration system
- Host
Interface
- UART
- CAN-FD
- SPI
- LIN
- RDIF (Radar Data Interface) for raw ADC sample capture
- Other interfaces available to
user application
- QSPI
- I2C
- JTAG
- GPIOs
- PWM Interface
- Internal memory
- 1MB of On-Chip RAM
- Configurable L3 shared memory for Radar Cube
- Data and Code RAM of (512/640/768KB)
- Functional Safety-Compliant
- Developed for functional safety applications
- Hardware integrity up to ASIL-B compliant
- FCCSP package having 12 x 12 BGA grid, 102 BGA balls; Package size: 6.45mm x 6.45mm
- AEC Q-100 Qualified
- Clock source
- 40.0MHz crystal for primary clock
- Supports externally driven clock (Square/Sine) at 40.0MHz
- 32kHz internal oscillator for low power operations
- Supports temperature operating
range
- Operating junction temperature range: –40°C to 125°C
The AWRL6432 mmWave Sensor device is an integrated single chip mmWave sensor based on FMCW radar technology. The device is capable of operation in the 57GHz to 63.9GHz band and is partitioned into mainly four power domains:
- RF/Analog Sub-System: This block includes all the RF and Analog components required to transmit and receive the RF signals.
- Front-End Controller sub-System (FECSS): FECSS contains processor ARM Cortex M3, responsible for radar front-end configuration, control, and calibration.
- Application Sub-System (APPSS): APPSS is where the device implements a user programmable ARM Cortex M4 allowing for custom control and automotive interface applications. Top Sub-System (TOPSS) is part of the APPSS power domain and contains the clocking and power management sub-blocks.
- Hardware Accelerator (HWA): HWA block supplements the APPSS by offloading common radar processing such as FFT, Constant False Alarm rate (CFAR), scaling, and compression.
AWRL6432 is specifically designed to have separate control for each of the above-mentioned power domains to control the states (power ON or OFF) based on use case requirements. The device also features the capability to exercise various low-power states like sleep and deep sleep, where low-power sleep mode is achieved by clock gating and by turning off the internal IP blocks of the device. The device also provides the option of keeping some contents of the device, like Application image or RF profile retained in such scenarios.
Additionally, the device is built with TI’s low power 45nm RF CMOS process and enables unprecedented levels of integration in an extremely small form factor. AWRL6432 is designed for low power, self-monitored, ultra-accurate radar systems in the automotive space for applications like child presence detection, intrusion monitoring, gesture detection, and occupancy detection.
추가 정보
TI 개발자 영역을 방문하여 평가 및 개발을 시작하십시오.
관심 가지실만한 유사 제품
비교 대상 장치와 유사한 기능.
기술 자료
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
AWRL6432BOOST — 단일 칩 저전력 mmWave 레이더 센서용 AWRL6432BOOST BoosterPack™ 평가 모듈
AWRL6432BOOST는 FR4 기반 안테나가 있는 AWRL6432를 위한 사용이 간편한 저전력 60GHz mmWave 센서 평가 키트입니다. 이 보드를 사용하면 포인트 클라우드 데이터 및 Power-over-USB 인터페이스에 액세스할 수 있습니다.
AWRL6432BOOST는 DCA1000EVM에 대한 직접 연결을 지원합니다. BoosterPack은 mmWave 도구, 시연, 그리고 mmWave 소프트웨어 개발 키트(MMWAVE-L-SDK) 및 Code Composer Studio™ IDE(통합 개발 환경)(CCSTUDIO) (...)
MURATA-3P-AUTORADAR-Q1 — 오토모티브 제품용 Murata mmWave 레이더 센서 모듈
VENTROPIC-3P-NF-RADAR — MMWAVE레이더 센서용 VENTROPIC-NF 레이더 모듈
VENTROPIC-RPI is a radar development module that integrates Bluetooth and Wi-Fi communication functions, simplifying the development and market entry process for customer products. The built-in firmware supports various algorithms for smart home, elderly care, medical health, and other scenarios (...)
TSK-3P-BLUEBOX — TASKING BlueBox hardware debugger
TASKING’s Debug, Trace, and Test tools offer comprehensive solutions for efficient debugging, tracing, and testing of TI's embedded systems. The scalable TASKING BlueBox debuggers allow users to easily flash, debug, and test across TI's portfolio. Development on TI hardware is made even easier with (...)
SMS-3P-ADAS-RADAR-HW-SW — ADAS 및 컴포트 시스템을 위한 맞춤형 레이더 센서 개발을 위한 스마트마카이크로 엔지니어링 서비스
CPD(어린이 탑승 감지), 침입 감지, SBR(시트 벨트 리마인더), 제스처 감지, 동작 감지 및 운전자 및 승객 모니터링을 위한 생명 징후 감지를 위한 상태 모니터링 등의 편안함과 안전 애플리케이션을 위한 TI 부품을 기반으로 한 60GHz~64GHz 실내 레이더 플랫폼입니다.
자동 사이드 도어, 트렁크 또는 프렁크를 위한 제스처 및 장애물 감지와 같은 ADAS 컴포트 애플리케이션을 위한 TI 부품을 기반으로 하는 76GHz~81GHz 초단거리 레이더 플랫폼입니다.
HS-3P-77-3D-WGA-LOP-4X4 — HUBER+SUHNER의 ADAS 레이더 센서를 위한 안테나 설계
77GHz 3D 도파관 안테나 4TX 4R - RF 기판 독립형 솔루션 제품군
Huber+SUHNER는 RF 기판 독립 솔루션용으로 설계된 2세대 3D 금속 플라스틱 도파관 안테나를 개발 및 제조하고 있습니다. 독점 인터페이스로 구현된 이 첨단 기술은 125mm2의 소형 포트 영역에서 전체 차량용 77GHz 레이더 대역(76GHz~81GHz)을 포함하는 4TX, 4RX 구성 채널로 차세대 고밀도 LOP(Launch-on-Package) 모놀리식 마이크로파 집적 회로(MMIC)를 지원합니다. 안테나 설계는 MMIC 패키지 크기를 (...)
GAPW-3P-ANTENNA — GapWaves의 ADAS 레이더 센서용 안테나 설계
Gapwaves offers high-performance, low-loss, and cost-efficient waveguide antennas for short-, mid- and long-range automotive radars and industrial applications. Our antennas feature a flexible design and a compact form factor, robust contact-free PCB integration and support contact-free LoP (...)
MMWAVE-L-SDK — mmWave SDK for xWRL6432, IWRL6432AOP, IWRL6432W and xWRL1432
mmWave 저전력 SDK(소프트웨어 개발 키트)는 TI의 저전력 mmWave 센서를 이용한 애플리케이션 평가 및 개발을 지원하는 소프트웨어 패키지 컬렉션입니다. 이 도구에는 고객의 설계 요구를 지원하기 위한 MMWAVE-L-SDK 및 MMWAVE-L-SDK-6 컴패니언 패키지가 포함됩니다.
MMWAVE-L-SDK 및 MMWAVE-L-SDK-6는 mmWave 감지 포트폴리오를 위한 통합형 소프트웨어 플랫폼으로, 간편한 설정과 신속한 기본 작동을 통해 평가 및 개발 환경으로의 빠른 접근을 제공합니다. MMWAVE-L-SDK 및 (...)
CCSTUDIO — Code Composer Studio integrated development environment (IDE)
CCStudio™ IDE is part of TI's extensive CCStudio™ development ecosystem and is an integrated development environment for TI's microcontrollers, processors, wireless connectivity devices, and radar sensors. CCStudio IDE is available as desktop or cloud-based applications. The cloud version (...)
EDGE-AI-STUDIO — Edge AI Studio
Edge AI Studio는 TI 프로세서, 마이크로컨트롤러, 레이더 센서의 에지 AI 개발을 가속화하기 위해 설계된 그래픽 및 명령줄 툴 모음입니다. TI Model Zoo의 모델을 활용해 개념 증명을 개발하든,
자체 모델을 활용하든, Edge AI Studio는 필요한 모든 툴을 제공합니다.
Edge AI Studio 그래픽 사용자 인터페이스는 라이브 개발 플랫폼에 배포할 모델을 교육 및 컴파일하고, 데이터를 수집하고 데이터에 주석을 추가하기 위한 완전 통합 솔루션을 제공합니다. TI Model Zoo에서 다양한 사전 학습된 (...)
EDGE-AI-STUDIO-MCU — Edge AI Studio for Microcontrollers
Edge AI Studio는 TI 프로세서, 마이크로컨트롤러, 레이더 센서의 에지 AI 개발을 가속화하기 위해 설계된 그래픽 및 명령줄 툴 모음입니다. TI Model Zoo의 모델을 활용해 개념 증명을 개발하든,
자체 모델을 활용하든, Edge AI Studio는 필요한 모든 툴을 제공합니다.
Edge AI Studio 그래픽 사용자 인터페이스는 라이브 개발 플랫폼에 배포할 모델을 교육 및 컴파일하고, 데이터를 수집하고 데이터에 주석을 추가하기 위한 완전 통합 솔루션을 제공합니다. TI Model Zoo에서 다양한 사전 학습된 (...)
MMWAVE-STUDIO-3G — mmWave studio GUI tools for third-generation parts (xWRLx432)
MMWAVE-STUDIO는 mmWave 센서 모듈을 구성 및 제어하고 오프라인 분석을 위해 ADC(아날로그-디지털) 데이터를 수집하는 기능을 제공하는 독립 실행형 Windows® GUI입니다. ADC 데이터 캡처는 라디오 주파수(RF) 성능 및 신호 처리 알고리즘의 PC 개발을 평가하고 특성화할 수 있도록 고안되었습니다.
MMWAVE-STUDIO는 처프 설계를 평가 및 프로토타이핑하고, 레이더 장치의 고급 기능을 사용해 실험을 합니다.
MMWAVE-STUDIO는 ADC 데이터를 직접 수집하고 저수준 처프 매개 변수를 미세 조정하는 (...)
TSK-3P-VX-TOOLSET — Arm용 TASKING VX-toolset
Arm용 VX-Toolset은 일부 Cortex-M 및 Cortex-R 코어 장치의 안전 필수 임베디드 소프트웨어 개발을 위해 인증된 컴파일러 툴체인입니다. Eclipse IDE 통합, 고급 멀티코어 지원, TASKING BlueBox 디버거와의 호환성을 제공하는 VX-toolset은 개발을 단순화합니다. 최대 ASIL D까지의 ISO 26262 및 ISO 21434 규격 준수를 위해 TÜV NORD 인증을 획득했습니다.
RADAR-ACADEMY — mmWave Radar Academy
TI-DEVELOPER-ZONE — Start embedded development on your desktop or in the cloud
MMWAVE-SENSING-ESTIMATOR-CLOUD — mmWave sensing estimator cloud development on TI Resource Explorer
UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors
UniFlash는 TI의 광범위한 CCStudio™ 개발 에코시스템의 일부로, TI 마이크로컨트롤러 및 무선 연결 장치의 온칩 플래시와 TI 프로세서의 온보드 플래시를 프로그래밍하기 위한 소프트웨어 도구입니다. UniFlash는 그래픽 및 명령줄 인터페이스를 모두 제공하며, 데스크톱 또는 클라우드 환경에서 실행할 수 있습니다.
UniFlash는 CCStudio™ 개발자 영역의 클라우드에서 실행하거나 Windows®, Linux®, macOS® 컴퓨터에서 다운로드해 사용할 수 있습니다.
macOS는 mmWave, AMx, K2G 및 (...)
RADAR-TOOLBOX — Radar evaluation and development support package with example projects, documentation and tools
VCTR-3P-MICROSAR — 마이크로컨트롤러 및 고성능 컴퓨터(HPC)용 벡터 MICROSAR AUTOSAR 소프트웨어
MICROSAR 및 DaVinci 제품군은 정교한 임베디드 소프트웨어 및 마이크로 컨트롤러 및 HPC를 위한 강력한 개발 툴로 ECU 개발을 간소화합니다. 고급 인프라 소프트웨어를 사용하면 ECU를 위한 최적의 기반을 만들고 관련 툴로 수반되는 모든 개발 작업을 간소화할 수 있습니다. MICROSAR 내장 소프트웨어는 AUTOSAR 클래식 및 적응형과 같은 관련 표준에 따라 개발되었습니다. 이 소프트웨어는 ISO 26262까지 ASIL D에 따른 안전 관련 애플리케이션에도 적합합니다. 또한, 지능형 사이버 보안 기능은 무단 액세스 (...)
TIDEP-01037 — 저전력 실내 레퍼런스 설계
이 설계는 TI의 단일 칩 60GHz 차량용 레이더 센서인 AWRL6432를 기반으로 하는 저전력 소형 폼 팩터 레퍼런스 설계입니다. 이 설계는 높은 RF 성능의 PCB 재료를 사용하며, CPD(어린이 탑승 감지) 및 ID(침입자 감지)와 같은 실내 감지 최종 애플리케이션을 대상으로 합니다. AWRL6432 장치는 머신 러닝 기반 존재 및 감지 알고리즘을 실행하여 차량 탑승자를 감지하고 분류합니다.
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| FCCSP (AMF) | 102 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.