IWRL1432
- FMCW Transceiver
- Integrated PLL, transmitter, receiver, baseband and ADC
- 76-81GHz coverage with 5GHz continuous bandwidth
- 3 receive channels and 2 transmit channels
- Short range
- 11dBm typical output power per Tx
- 14dB typical noise figure
- -89dBc/Hz typical phase noise at 1MHz
- FMCW operation
- 5MHz IF bandwidth, real-only Rx channels
- Ultra-accurate chirp engine based on fractional-N PLL
- Per transmitter binary phase shifter
- Processing elements
- Arm M4F core with single precision FPU (160 MHz)
- TI Radar Hardware Accelerator (HWA 1.2) for FFT, Log Magnitude, and CFAR operations (80MHz)
- Supports multiple low-power
modes
- Idle mode and deep sleep mode
- Power management
- 1.8V and 3.3V IO support
- Built-in LDO network for enhanced PSRR
- BOM-Optimized and Power-Optimized modes
- One or two power rails for 1.8V IO mode, two or three power rails for 3.3V IO mode
- Package size of FCCSP device: 6.45mm x 6.45mm
- Built-in calibration and
self-test
- Built-in firmware (ROM)
- Self-Contained on chip calibration system
- Host
Interface
- UART
- CAN-FD
- SPI
- RDIF (Radar Data Interface) for raw ADC sample capture
- Other interfaces available to
user application
- QSPI
- I2C
- JTAG
- GPIOs
- PWM Interface
- Internal Memory
- 1MB of On-Chip RAM
- Configurable L3 shared memory for Radar Cube
- Data and Code RAM of (512/640/768KB)
- Functional Safety-Compliant Targeted
- Developed for Functional Safety Applications
- Hardware integrity up to SIL 2 targeted
- FCCSP package with 12 x 12, 102 BGA balls
- Clock source
- 40.0MHz Crystal for primary clock
- Supports externally driven clock (Square/Sine) at 40.0MHz
- 32kHz internal oscillator for low power operations
- Supports temperature operating
range
- Operating Junction Temperature Range: –40°C to 105°C
The IWRL1432 mmWave Sensor device is an integrated single chip mmWave sensor based on FMCW radar technology. The device is capable of operation in the 76GHz to 81GHz band and is partitioned into mainly four power domains:
- RF/Analog Sub-System: This block includes all the RF and Analog components required to transmit and receive the RF signals.
- Front-End Controller sub-System (FECSS): FECSS contains processor, responsible for radar front-end configuration, control, and calibration.
- Application Sub-System (APPSS): APPSS is where the device implements a user programmable ARM Cortex M4 allowing for custom control and automotive interface applications. Top Sub-System (TOPSS) is part of the APPSS power domain and contains the clocking and power management sub-blocks.
- Hardware Accelerator (HWA): HWA block supplements the APPSS by offloading common radar processing such as FFT, Constant False Alarm rate (CFAR), scaling, and compression.
IWRL1432 is specifically designed to have separate controls for each of the above-mentioned power domains to control their states (power ON or OFF) based on use case requirements. The device also features the capability to exercise various low-power states like sleep and deep sleep, where low-power sleep mode is achieved by clock gating and by turning off the internal IP blocks of the device. The device also provides the option of keeping some contents of the device, like Application image or RF profile retained in such scenarios.
Additionally, the device is built with TI’s low power 45nm RF CMOS process and enables unprecedented levels of integration in an extremely small form factor. IWRL1432 is designed for low power, self-monitored, ultra-accurate radar systems in the industrial (and personal electronics) space for applications such as building/factory automation, commercial/residential security, personal electronics, presence/motion detection, and gesture detection/recognition for human machine interfaces
추가 정보
TI 개발자 영역을 방문하여 평가 및 개발을 시작하십시오.
기술 자료
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
IWRL1432BOOST — 단일 칩 77GHz mmWave 저전력 센서용 IWR1432 BoosterPack™ 평가 모듈
IWRL1432BOOST는 IWRL1432 mmWave 레이더 센서에 기반을 둔 사용이 편리한 77GHz mmWave 센서 평가 키트로, 온보드 ROGERS RO4835 LoPRO 기반 안테나가 포함되어 있습니다. 이 보드를 사용하면 포인트 클라우드 데이터 및 Power-over-USB 인터페이스에 액세스할 수 있습니다. IWRL1432BOOST는 DCA1000EVM 개발 키트에 대한 직접 연결을 지원합니다.
이 키트는 저전력 mmWave 레이더 센서용 mmWave 소프트웨어 개발 키트 (MMWAVE-L-SDK)) 및 TI의 (...)
IWRL1432BOOST-BSD — 저전력 76GHz~81GHz 산업용 레이더 센서를 지원하는 BSD용 IWRL1432 평가 모듈
IWRL1432BOOST-BSD는 온보드 ROGERS RO3003 고성능 안테나가 포함된 IWRL1432 장치를 기반으로 하는 사용이 편리한 77GHz mmWave 센서 평가 키트입니다. 이 보드를 사용하면 포인트 클라우드 데이터 및 Power-over-USB 인터페이스에 액세스할 수 있습니다. IWRL1432BOOST-BSD에는 이 인터페이스가 필요한 애플리케이션을 위해 12V로 작동하는 TCAN4550도 있습니다.
VENTROPIC-3P-NF-RADAR — MMWAVE레이더 센서용 VENTROPIC-NF 레이더 모듈
VENTROPIC-RPI is a radar development module that integrates Bluetooth and Wi-Fi communication functions, simplifying the development and market entry process for customer products. The built-in firmware supports various algorithms for smart home, elderly care, medical health, and other scenarios (...)
D3-3P-RVP-TDA2X — TDA2 프로세서용 D3 임베디드 DesignCore® RVP-TDA2x 개발 키트
RVP-TDA2x는 하이엔드 ADAS 시스템을 위한 다중 카메라 플랫폼입니다. ARM A15 애플리케이션 프로세서 2개, 최대 4개의 EVE(Vision Acceleration PAC) 코프로세서, 하드웨어 가속 H.264 인코더가 포함되어 있습니다. 개발 키트는 8개의 카메라 입력을 지원하지만 필요에 따라 사용자 지정할 수 있습니다. 키트 구매에는 소프트웨어 배포 및 일회용 라이센스가 포함됩니다.
HS-3P-77-3D-WGA-LOP-4X4 — HUBER+SUHNER의 ADAS 레이더 센서를 위한 안테나 설계
77GHz 3D 도파관 안테나 4TX 4R - RF 기판 독립형 솔루션 제품군
Huber+SUHNER는 RF 기판 독립 솔루션용으로 설계된 2세대 3D 금속 플라스틱 도파관 안테나를 개발 및 제조하고 있습니다. 독점 인터페이스로 구현된 이 첨단 기술은 125mm2의 소형 포트 영역에서 전체 차량용 77GHz 레이더 대역(76GHz~81GHz)을 포함하는 4TX, 4RX 구성 채널로 차세대 고밀도 LOP(Launch-on-Package) 모놀리식 마이크로파 집적 회로(MMIC)를 지원합니다. 안테나 설계는 MMIC 패키지 크기를 (...)
WZ-3P-1001089 — 혼 안테나 포함 Wellenzahl RAPIDv3.21ti_L 단상태 IWRL1432 레이더 모듈
RAPIDv3.2ti_L + WR-12 원형 경적
높은 정밀도 또는 충전 레벨 애플리케이션 평가
-
사전 정의된 레이더 프로필
-
원시 ADC 데이터 캡처
-
고정밀 측정을 위한 알고리즘 구현됨
-
Wellenzahl 정적 및 동적 배경 추정기 - 충전 레벨 애플리케이션 등에 완벽하게 적합
GAPW-3P-ANTENNA — GapWaves의 ADAS 레이더 센서용 안테나 설계
Gapwaves offers high-performance, low-loss, and cost-efficient waveguide antennas for short-, mid- and long-range automotive radars and industrial applications. Our antennas feature a flexible design and a compact form factor, robust contact-free PCB integration and support contact-free LoP (...)
WZ-3P-1000303 — Wellenzahl 유전체 렌즈 HDPE CNC 가공품
RAPIDv3 장착을 위한 PCB 스페이서 포함 RAPIDv3 모듈(60/77/122GHz)용 유전체 렌즈
WZ-3P-1001086 — Wellenzahl 유전체 렌즈 PLA 3D 프린팅
RAPIDv3 장착을 위한 PCB 스페이서 포함 RAPIDv3 모듈(60/77/122GHz)용 유전체 렌즈
MMWAVE-L-SDK — mmWave SDK for xWRL6432, IWRL6432AOP, IWRL6432W and xWRL1432
mmWave 저전력 SDK(소프트웨어 개발 키트)는 TI의 저전력 mmWave 센서를 이용한 애플리케이션 평가 및 개발을 지원하는 소프트웨어 패키지 컬렉션입니다. 이 도구에는 고객의 설계 요구를 지원하기 위한 MMWAVE-L-SDK 및 MMWAVE-L-SDK-6 컴패니언 패키지가 포함됩니다.
MMWAVE-L-SDK 및 MMWAVE-L-SDK-6는 mmWave 감지 포트폴리오를 위한 통합형 소프트웨어 플랫폼으로, 간편한 설정과 신속한 기본 작동을 통해 평가 및 개발 환경으로의 빠른 접근을 제공합니다. MMWAVE-L-SDK 및 (...)
CCSTUDIO — Code Composer Studio integrated development environment (IDE)
CCStudio™ IDE is part of TI's extensive CCStudio™ development ecosystem and is an integrated development environment for TI's microcontrollers, processors, wireless connectivity devices, and radar sensors. CCStudio IDE is available as desktop or cloud-based applications. The cloud version (...)
MMWAVE-STUDIO-3G — mmWave studio GUI tools for third-generation parts (xWRLx432)
MMWAVE-STUDIO는 mmWave 센서 모듈을 구성 및 제어하고 오프라인 분석을 위해 ADC(아날로그-디지털) 데이터를 수집하는 기능을 제공하는 독립 실행형 Windows® GUI입니다. ADC 데이터 캡처는 라디오 주파수(RF) 성능 및 신호 처리 알고리즘의 PC 개발을 평가하고 특성화할 수 있도록 고안되었습니다.
MMWAVE-STUDIO는 처프 설계를 평가 및 프로토타이핑하고, 레이더 장치의 고급 기능을 사용해 실험을 합니다.
MMWAVE-STUDIO는 ADC 데이터를 직접 수집하고 저수준 처프 매개 변수를 미세 조정하는 (...)
RADAR-ACADEMY — mmWave Radar Academy
TI-DEVELOPER-ZONE — Start embedded development on your desktop or in the cloud
MMWAVE-SENSING-ESTIMATOR-CLOUD — mmWave sensing estimator cloud development on TI Resource Explorer
UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors
UniFlash는 TI의 광범위한 CCStudio™ 개발 에코시스템의 일부로, TI 마이크로컨트롤러 및 무선 연결 장치의 온칩 플래시와 TI 프로세서의 온보드 플래시를 프로그래밍하기 위한 소프트웨어 도구입니다. UniFlash는 그래픽 및 명령줄 인터페이스를 모두 제공하며, 데스크톱 또는 클라우드 환경에서 실행할 수 있습니다.
UniFlash는 CCStudio™ 개발자 영역의 클라우드에서 실행하거나 Windows®, Linux®, macOS® 컴퓨터에서 다운로드해 사용할 수 있습니다.
macOS는 mmWave, AMx, K2G 및 (...)
RADAR-TOOLBOX — Radar evaluation and development support package with example projects, documentation and tools
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| FCCSP (AMF) | 102 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.