LM5168-Q1
- AEC-Q100-qualified for automotive applications
- Device temperature grade 1: –40°C to +125°C, ambient temperature range
- Designed for reliability in rugged applications
- Wide input voltage range of 6 V to 120 V
- Junction temperature range: –40°C to +150°C
- Fixed 3-ms internal soft-start timer
- Peak and valley current-limit protection
- Input UVLO and thermal shutdown protection
- Suited for scalable automotive HEV/EV power
supplies
- Low minimum on and off times of 50 ns
- Adjustable switching frequency up to 1 MHz
- Diode emulation for high light-load efficiency
- Auto mode with low-quiescent current (< 10 µA)
- FPWM for fly-buck converter capability
- 3-µA shutdown quiescent current
- Pin-to-pin compatible with LM5164-Q1, LM5163-Q1, LM5017, LM5013-Q1and LM34927
- Integration reduces solution size
and cost
- COT mode control architecture
- Integrated 1.9-Ω NFET buck switch
- Integrated 0.71-Ω NFET synchronous rectifier
- 1.2-V internal voltage reference
- No loop compensation components
- Internal VCC bias regulator and boot diode
- Open-drain power-good indicator
- SOIC PowerPAD™ integrated circuit package
The LM5169 -Q1 and LM5168 -Q1 synchronous buck converters are designed to regulate over a wide input voltage range, minimizing the need for external surge suppression components. A minimum controllable on time of 50 ns facilitates large step-down conversion ratios, enabling the direct step-down from a 48-V nominal input to low-voltage rails for reduced system complexity and solution cost. The LM516x -Q1 operates during input voltage dips as low as 6 V, at nearly 100% duty cycle if needed, making it an excellent choice for wide input supply range industrial and high cell count battery pack applications.
With integrated high-side and low-side power MOSFETs, the LM5169 -Q1 delivers up to 0.65-A of output current and the LM5168 -Q1 delivers up to 0.3-A of output current. A constant on-time (COT) control architecture provides nearly constant switching frequency with excellent load and line transient response. The LM516x -Q1 is available in FPWM or auto mode versions. FPWM mode provides forced CCM operation across the entire load range supporting isolated fly-buck converter applications. Auto mode enables ultra-low IQ and diode emulation mode operation for high light-load efficiency.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | LM516x-Q1 0.65/0.3-A, 120-V Step-Down Converter w/ Fly-Buck Converter Capability datasheet (Rev. A) | PDF | HTML | 2022. 9. 8 | |
| Product overview | Isolated Power Topologies for PLC I/O Modules and Other Low-Power Applications (Rev. A) | PDF | HTML | 2024. 8. 20 | ||
| 애플리케이션 노트 | Inverting Buck-Boost Application for the LM5168 | PDF | HTML | 2023. 2. 24 | ||
| 기능 안전 정보 | LM516x-Q1 Functional Safety, FIT Rate, Failure Mode Distribution and Pin FMA (Rev. A) | PDF | HTML | 2022. 9. 1 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
LM5168FEVM — LM5168 평가 모듈 115V 플라이 벅 레귤레이터
LM5168PEVM — LM5168P 115V DC/DC 벅 레귤레이터 평가 모듈
LM5168P 평가 모듈(EVM)은 좁은 공간에서 높은 변환 효율을 달성하기 위해 동기 정류를 사용하는 115 V DC/DC 벅 레귤레이터입니다. 이 EVM은 20V~115V의 넓은 입력 전압 범위(최대 120V 절대 최대)에서 작동하며, 500kHz의 스위칭 주파수를 가지고 최대 0.3V에서 조정된 12V 출력을 제공합니다. 출력 전압은 1.5% 이상 설정값의 정확도를 제공하며, 외부 저항 분할기를 사용하여 조정할 수 있습니다. 이 모듈 설계에서는 넓은 입력 전압(넓은 VIN) 범위, 넓은 듀티 사이클 범위, 통합 고압측 전력 (...)
SNVR520 — LM5169 Quick Start Calculator
TIDA-020076 — 차량용 고전압 BMS 레퍼런스 설계: 18S 유선 또는 무선 셀 감시 장치
이 레퍼런스 설계는 최대 18개의 셀을 위한 셀 감시 장치를 구현합니다. 이 장치는 승용차, 상업용 차량 및 2륜차와 3륜차(72V보다 높은 전압에서 작동)에 사용되는 일반적인 고전압 배터리 범위를 지원하기 위해 데이지 체인으로 연결할 수 있습니다. 이 레퍼런스 설계는 유무선 BMS(배터리 관리 시스템) 성능을 나란히 비교할 수 있도록 유선 및 무선 접속 옵션을 모두 제공합니다.
TIDA-020101 — 차량용 48V 300W HVAC 펌프, 송풍기 및 팬 레퍼런스 설계
이 레퍼런스 설계는 48V, 300W 피크 스마트 모터 BLDC(브러시리스 직류) 구현을 보여줍니다. 개별 접근 방식을 통해 55mm 직경의 작고 콤팩트하며 유연한 폼 팩터를 구현할 수 있습니다. 이 설계는 100μA 미만의 저전력 절전 모드를 유지합니다. 이 설계는 효율적인 작동을 촉진하기 위해 TI 반도체를 활용합니다. 이 아키텍처는 높은 전력, 정밀도 및 소형화가 필요해 까다로운 차량용 HVAC(난방, 환기 및 공조) 애플리케이션을 위한 견고한 기반을 제공합니다.
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| HSOIC (DDA) | 8 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.