LPV521
- For VS = 5V, typical unless otherwise noted:
- Supply current at VCM = 0.3V: 400nA (max)
- Operating voltage range: 1.6V to 5.5V
- Low TCVOS: 3.5µV/°C (max)
- VOS: 1mV (max)
- Input bias current: 40fA
- PSRR: 109dB
- CMRR: 102dB
- Open-loop gain: 132dB
- Gain bandwidth product: 6.2kHz
- Slew rate: 2.4V/ms
- Input voltage noise at f = 100Hz: 255nV/√Hz
- Temperature range: −40°C to +125°C
The LPV521 is a single, nanopower, 552nW amplifier designed for ultra-long-life battery applications. The operating voltage range of 1.6V to 5.5V coupled with typically 351nA of supply current make this device an excellent choice for RFID readers and remote-sensor nanopower applications. The device has an input common-mode voltage 0.1V over the rails, specified TCVOS, and voltage-swing-to-the-rail output performance. The LPV521 has a carefully designed CMOS input stage that outperforms competitors with typically 40fA IBIAS currents. This low input current significantly reduces IBIAS and IOS errors introduced in megohm resistance, high-impedance photodiode and charge sense applications. The LPV521 is a member of the PowerWise family, and has an exceptional power-to-performance ratio.
The wide input common-mode voltage range, specified 1mV VOS and 3.5µV/°C TCVOS enables accurate and stable measurement for both high-side and low-side current sensing.
EMI protection is designed into the device to reduce sensitivity to unwanted RF signals from cell phones or other RFID readers.
The LPV521 is offered in 5-pin SC70 and 8-pin PDIP packages.
기술 자료
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | LPV521 NanoPower, 1.8V, RRIO, CMOS Input, Operational Amplifier datasheet (Rev. E) | PDF | HTML | 2024/07/12 |
| Application brief | Simplifying Environmental Measurements in Power Conscious Factory and Building A (Rev. A) | 2018/01/09 | ||
| Application note | Advantages of using Nanopower Zero Drift Amp for Mobile Phone Battery Voltage Mo (Rev. A) | 2017/12/21 | ||
| E-book | The Signal e-book: A compendium of blog posts on op amp design topics | 2017/03/28 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
551012922-001 — SC-70 증폭기 범용 평가 보드
Texas Instrument offers this blank universal Evaluation Board to help you evaluate the performance of any low voltage, low power operational amplifier that is offered in the SC-70 package. Resistors, capacitors, or any other components can be easily mounted on this board. These components can be (...)
DIP-ADAPTER-EVM — DIP 어댑터 평가 모듈
소형 표면 실장 IC(집적 회로)와 쉽고 빠르며 경제적인 방식으로 인터페이싱하는 방법을 제공하는 DIP 어댑터 평가 모듈(DIP-ADAPTER-EVM)로 연산 증폭기 프로토타이핑 및 테스트 속도를 높이세요. 제품에 포함된 Samtec 터미널 스트립을 사용하여 지원되는 연산 증폭기를 연결하거나 기존 회로에 직접 연결할 수 있습니다.
DIP 어댑터 EVM 키트는 다음을 포함해 가장 널리 사용되는 6개의 업계 표준 패키지를 지원합니다.
- D 및 U(SOIC-8)
- PW(TSSOP-8)
- DGK(MSOP-8, VSSOP-8)
- (...)
DIYAMP-EVM — 범용 DIY(Do-it-yourself) 증폭기 회로 평가 모듈
DIYAMP-EVM은 엔지니어와 DIY 사용자에게 실제 증폭기 회로를 제공하여 설계 개념을 신속하게 평가하고 시뮬레이션을 검증할 수 있게 해주는 EVM(평가 모듈) 제품군입니다. 3가지 업계 표준 패키지(SC70, SOT-23, SOIC)로 제공되며 12가지 대중적인 증폭기 구성을 포함합니다. 예를 들어 증폭기, 필터, 안정성 보상 및 콤퍼레이터 구성이 있어 단일 및 이중 공급 장치 양쪽 모두에 적합합니다.
DIYAMP-EVM은 빠르고 간편한 프로토타이핑을 지원하며 일반적인 0805 또는 0603 표면 실장 부품을 사용합니다. (...)
ANALOG-ENGINEER-CALC — 아날로그 엔지니어의 계산기
이 계산기는 독립 실행형 툴로 유용할 뿐만 아니라 아날로그 엔지니어의 포켓 레퍼런스에 설명된 개념과도 잘 어울립니다.
CIRCUIT060013 — T-네트워크 피드백 회로가 있는 인버팅 증폭기
CIRCUIT060015 — 조정 가능한 레퍼런스 전압 회로
CIRCUIT060074 — 콤퍼레이터 회로를 사용한 고압측 전류 감지
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 착수하기 (...)
TINA-TI — SPICE 기반 아날로그 시뮬레이션 프로그램
TIDA-00759 — 10년 코인 셀 배터리 수명 및 블루투스 스마트를 지원하는 저전력 PRI 동작 감지기 레퍼런스 디자인
TIDA-01546 — 배터리로 구동되는 스마트 유량 계량기의 배터리 및 시스템 상태 모니터링 레퍼런스 설계
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| PDIP (P) | 8 | Ultra Librarian |
| SOT-SC70 (DCK) | 5 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치