TMAG5273
- Configurable power modes
including:
- 2.3mA active mode current
- 1µA wake-up and sleep mode current
- 5nA sleep mode current
- Selectable linear magnetic range at X, Y, or Z axis:
- TMAG5273x1: ±40mT, ±80mT
- TMAG5273x2: ±133mT, ±266mT
- Interrupt signal from user-defined magnetic and temperature threshold cross
- 5% (typical) sensitivity drift
- Integrated angle CORDIC calculation with gain and offset adjustment
- 20kSPS single axis conversion rate
- Configurable averaging up to 32x for noise reduction
- Conversion trigger by I2C or dedicated INT pin
- Optimized I2C
interface with cyclic redundancy check (CRC):
- Maximum 1MHz I2C clock speed
- Special I2C frame reads for improved throughput
- Factory-programmed and user-configurable I2C addresses
- Integrated temperature compensation for multiple magnet types
- Built-in temperature sensor
- 1.7V to 3.6V supply voltage VCC range
- Operating temperature range: –40℃ to +125℃
The TMAG5273 is a low-power linear 3D Hall-effect sensor designed for a wide range of industrial and personal electronics applications. This device integrates three independent Hall-effect sensors in the X, Y, and Z axes. A precision analog signal-chain along with an integrated 12-bit ADC digitizes the measured analog magnetic field values. The I2C interface, while supporting multiple operating VCC ranges, provides seamless data communication with low-voltage microcontrollers. The device has an integrated temperature sensor available for multiple system functions, such as thermal budget check or temperature compensation calculation for a given magnetic field.
The TMAG5273 can be configured through the I2C interface to enable any combination of magnetic axes and temperature measurements. Additionally, the device can be configured to various power options (including wake-up and sleep mode) allowing designers to optimize system power consumption based on system-level needs. Multiple sensor conversion schemes and I2C read frames help optimize throughput and accuracy. A dedicated INT pin can act as a system interrupt during low power wake-up and sleep mode, and can also be used by a microcontroller to trigger a new sensor conversion.
An integrated angle calculation engine (CORDIC) provides full 360° angular position information for both on-axis and off-axis angle measurement topologies. The angle calculation is performed using two user-selected magnetic axes. The device features magnetic gain and offset correction to mitigate the impact of system mechanical error sources.
The TMAG5273 is offered in four different factory-programmed I2C addresses. The device also supports additional I2C addresses through the modification of a user-configurable I2C address register. Each orderable part can be configured to select one of two magnetic field ranges that suits the magnet strength and component placement during system calibration.
The device performs consistently across a wide ambient temperature range of –40°C to +125°C.
관심 가지실만한 유사 제품
비교 대상 장치와 동일한 기능을 지원하는 핀 대 핀.
기술 자료
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
LDC-HALL-HMI-EVM — 유도성 터치 및 자기 다이얼 비접촉 사용자 인터페이스 설계용 평가 모듈
TMAG5273EVM — TMAG5273 I²C 인터페이스를 갖춘 저전력, 선형 3D 홀 효과 센서용 평가 모듈
TMAG5273EVM은 선형 3D 홀 효과 센서인 TMAG5273 장치의 주요 기능과 성능을 평가하기 위한 편리한 플랫폼입니다. 평가 모듈(EVM)에는 자석 1개와 TMAG5273 도터 보드가 포함되어 있습니다. EVM은 함께 제공되는 그래픽 사용자 인터페이스(GUI)를 지원하는 센서 컨트롤러 보드(별도 판매), TI-SCB와 함께 작동합니다. 또한 단일 디바이스로 각도 측정 및 푸시 버튼의 일반적인 기능을 테스트할 수 있는 3D 인쇄 회전 및 푸시 모듈도 포함되어 있습니다.
TMAG5273-MSPM0L1306-CODE-EXAMPLE — Example Code for the TMAG5273EVM connected to the LP-MSPM01306
TMAG5X73-CODE-EXAMPLE — TMAG5273 and TMAG5173-Q1 code example
TMAG5X73EVM-GUI — TMAG5173EVM and TMAG5273EVM GUI
SBAC295 — TMAG5173EVM and TMAG5273EVM BSL Batch File
TI-MAGNETIC-SENSE-SIMULATOR — TI Magnetic sensing simulation tool
HALL-PROXIMITY-DESIGN — Magnetic Sensing Proximity Tool
HALL-PROXIMITY-DESIGN은 자석 및 홀(Hall) 효과 센서 시스템을 위한 신속한 반복 설계를 도와주는 소프트웨어 도구입니다.
SBAR012 — Angle Error Calculator for Linear 3D Hall-effect Sensors
TIDA-010243 — 독립형 ADC를 지원하는 3상 전류 변압기 e-미터 레퍼런스 설계
이 레퍼런스 설계는 고성능, 멀티 채널 ADC(아날로그-디지털 컨버터)를 사용하여 클래스 0.1 3상 에너지 측정을 구현합니다. 이 ADC는 8kHz에서 전류 변압기(CT)를 샘플링하여 AC 주전원 각 레그의 전류 및 전압을 측정합니다. 이 레퍼런스 설계는 넓은 입력 전류 범위(0.01A~100A)에서 높은 정확도를 달성하며 개별 고조파 분석과 같은 전력 품질 기능에 필요한 높은 샘플링 주파수를 지원합니다. 계측용 TI Arm® Cortex®-M0+ 호스트 마이크로컨트롤러를 사용할 때 32kSPS의 ADC 샘플 레이트를 달성할 수 (...)
TIDA-010244 — 3상 션트 기반 에너지 계측 레퍼런스 설계
TIDA-010944 — 단상 및 분할 위상 션트 에너지 계측 레퍼런스 설계
TIDA-010950 — 전원 조정 및 홀 효과 위치 감지를 지원하는 댐퍼 및 EEV 컨트롤러 레퍼런스 설계
이 레퍼런스 설계는 댐퍼 액추에이터 및 전자 확장 밸브를 위한 듀얼 모터 드라이브 솔루션을 보여줍니다. 여러 모터 드라이브에는 15VDC 소스에서 작동하는 양극 스테퍼 모터 드라이버 1개, 브러시리스 DC 모터 드라이버 1개가 포함되어 있습니다. 이 설계는 IEC 60335-1에서 정의된 저전력 회로 인증을 손쉽게 수행할 수 있는 정확한 전력 제한을 보여줍니다. 이 레퍼런스 설계에서는 밸브 또는 댐퍼의 위치를 제어하기 위한 0~10V 및 4~20mA 제어 인터페이스와 정확한 위치 감지에 사용되는 TMAG5273을 통합합니다.
TIDA-060039 — 유도성 터치 및 자기 다이얼 비접촉 사용자 인터페이스 레퍼런스 설계
이 레퍼런스 설계는 유도성 및 홀 효과 센서 기술을 사용하여 인간-기계 인터페이스를 제공합니다. 유도성 감지 장치는 매끄러운 표면에 8개의 각기 다른 터치 버튼을 생성하고, 홀 효과 센서는 추가 버튼으로 사용할 수 있는 회전식 자기 다이얼을 생성하는 데 사용됩니다.
유도성 감지 터치 버튼을 사용하면 누르는 힘을 사용해 버튼 누르기를 결정하는 강력한 솔루션을 제공할 수 있습니다. 따라서 먼지나 버튼 표면의 손상 같은 환경적 요인을 무시하고 장갑을 착용한 상태로 터치 버튼을 사용할 수 있습니다. 홀 효과 센서 다이얼은 무접촉 회전을 (...)
TIDA-060045 — 쿼드 3D 홀 효과 센서를 사용한 정확한 저지연 선형 위치 감지 레퍼런스 설계
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| SOT-23 (DBV) | 6 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.