首頁 電池管理 IC 電池充電器 IC
首頁
電池管理 IC
電池充電器 IC
最新

BQ24138

現行

具有 4uA 靜態電流的 I2C 控制、1 芯 5A 最大 14V 輸入降壓充電器

立即訂購
產品規格表

BQ24138

現行
產品規格表 立即訂購

產品詳細資料

Rating Catalog Operating temperature range (°C) to
Rating Catalog Operating temperature range (°C) to
DSBGA (YBG) 30 5.46 mm² 2.6 x 2.1
  • High-efficiency 5A, 1.5MHz, synchronous switch mode buck charger for single cell battery
    • >90% efficiency down to 10mA output current from 5V input
    • Charge current up to 5A in 80mA steps
    • Charge termination from 60 to 1000mA in 10mA steps
    • Flexible JEITA profile for safe charging over temperature
  • BATFET control to support shutdown and full system reset
    • 4µA quiescent current in battery only mode
    • 1.5µA quiescent current in ultra low power mode
    • 0.1µA battery leakage current in shutdown
  • Supports USB On-The-Go (OTG)
    • Boost mode operation with 3.84V to 7.52-V output
    • Programmable current limit up to 3.2A
  • Supports a wide range of input sources
    • 3.9V to 14 -V wide input operating voltage range with 22 -V absolute maximum input voltage
    • VINDPM threshold automatically tracks battery voltage
    • Input Current Optimizer (ICO) to maximize input power without overloading adapters
  • Efficient battery operation with 7mΩ BATFET
  • Narrow VDC (NVDC) power path management
    • System instant-on with depleted or no battery
    • Battery supplement when adapter is fully loaded
  • Flexible autonomous or I2C-controlled modes
  • Integrated 12-bit ADC for voltage, current, and temperature monitoring
  • High accuracy
    • ±0.5% charge voltage regulation
    • ±5% charge current regulation
    • ±5% input current regulation
  • Safety
    • Battery temperature sensing
    • Thermal regulation and thermal shutdown
    • Battery/converter overcurrent protection
    • Charging safety timer
  • High-efficiency 5A, 1.5MHz, synchronous switch mode buck charger for single cell battery
    • >90% efficiency down to 10mA output current from 5V input
    • Charge current up to 5A in 80mA steps
    • Charge termination from 60 to 1000mA in 10mA steps
    • Flexible JEITA profile for safe charging over temperature
  • BATFET control to support shutdown and full system reset
    • 4µA quiescent current in battery only mode
    • 1.5µA quiescent current in ultra low power mode
    • 0.1µA battery leakage current in shutdown
  • Supports USB On-The-Go (OTG)
    • Boost mode operation with 3.84V to 7.52-V output
    • Programmable current limit up to 3.2A
  • Supports a wide range of input sources
    • 3.9V to 14 -V wide input operating voltage range with 22 -V absolute maximum input voltage
    • VINDPM threshold automatically tracks battery voltage
    • Input Current Optimizer (ICO) to maximize input power without overloading adapters
  • Efficient battery operation with 7mΩ BATFET
  • Narrow VDC (NVDC) power path management
    • System instant-on with depleted or no battery
    • Battery supplement when adapter is fully loaded
  • Flexible autonomous or I2C-controlled modes
  • Integrated 12-bit ADC for voltage, current, and temperature monitoring
  • High accuracy
    • ±0.5% charge voltage regulation
    • ±5% charge current regulation
    • ±5% input current regulation
  • Safety
    • Battery temperature sensing
    • Thermal regulation and thermal shutdown
    • Battery/converter overcurrent protection
    • Charging safety timer

The BQ24138 is a highly-integrated 5A switch-mode battery charge management and system power path management device for single cell Li-Ion and Li-polymer batteries. The design is highly integrated with built-in current sensing, loop compensation, input reverse-blocking FET (RBFET, Q1), high-side switching FET (HSFET, Q2), low-side switching FET (LSFET, Q3), and battery FET (BATFET, Q4) between system and battery. The device uses NVDC power path management, regulating the system slightly above the battery voltage without dropping below a configurable minimum system voltage. The low impedance power path optimizes switch-mode operation efficiency, reduces battery charging time and extends battery life during discharging phase. The I2C serial interface with charging and system settings makes BQ24138 a truly flexible design.

The BQ24138 is a highly-integrated 5A switch-mode battery charge management and system power path management device for single cell Li-Ion and Li-polymer batteries. The design is highly integrated with built-in current sensing, loop compensation, input reverse-blocking FET (RBFET, Q1), high-side switching FET (HSFET, Q2), low-side switching FET (LSFET, Q3), and battery FET (BATFET, Q4) between system and battery. The device uses NVDC power path management, regulating the system slightly above the battery voltage without dropping below a configurable minimum system voltage. The low impedance power path optimizes switch-mode operation efficiency, reduces battery charging time and extends battery life during discharging phase. The I2C serial interface with charging and system settings makes BQ24138 a truly flexible design.
filter 尋找其它 電池充電器 IC
下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 1
類型 標題 日期
* Data sheet BQ24138 I2 C Controlled, Single Cell 5A Charger With NVDC Power Path Management and USB OTG Boost Output datasheet PDF | HTML 2026年 1月 28日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

封裝 針腳 CAD 符號、佔位空間與 3D 模型
DSBGA (YBG) 30 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片