SN74AVC2T45-Q1
- Qualified for automotive applications
- Control inputs VIH/VIL levels are referenced to VCCA voltage
- Fully configurable dual-rail design allows each port to operate over the full 1.2V to 3.6V power-supply range
-
Operating temperature from -40°C to 105°C
- I/Os are 4.6V tolerant
- Ioff supports partial-power-down mode operation
- Maximum data rates
- 500Mbps (1.8V to 3.3V translation)
- 320Mbps (< 1.8V to 3.3V translation)
- 320Mbps (translate to 2.5V or 1.8V)
- 280Mbps (translate to 1.5V)
- 240Mbps (translate to 1.2V)
- Latch-up performance exceeds 100mA per JESD 78, Class II
- ESD protection exceeds JESD 22
- 8000V human-body model (A114-A)
- 200V machine model (A115-A)
- 1000V charged-device model (C101)
This dual-bit noninverting bus transceiver uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.2V to 3.6V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.2V to 3.6V. This allows for universal low-voltage bidirectional translation between any of the 1.2V, 1.5V, 1.8V, 2.5V, and 3.3V voltage nodes.
The SN74AVC2T45 is designed for asynchronous communication between two data buses. The logic levels of the direction-control (DIR) input activate either the B-port outputs or the A-port outputs. The device transmits data from the A bus to the B bus when the B-port outputs are activated and from the B bus to the A bus when the A-port outputs are activated. The input circuitry on both A and B ports always is active and must have a logic HIGH or LOW level applied to prevent excess ICC and ICCZ.
The SN74AVC2T45 is designed so that the DIR input is powered by VCCA.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when powered down.
The VCC isolation feature makes sure that if either VCC input is at GND, both ports are in the high-impedance state.
您可能會感興趣的類似產品
引腳對引腳且具備與所比較裝置相同的功能
技術文件
設計與開發
如需其他條款或必要資源,請按一下下方的任何標題以檢視詳細頁面 (如有)。
5-8-LOGIC-EVM — 適用於 5 針腳至 8 針腳 DCK、DCT、DCU、DRL 和 DBV 封裝的通用邏輯評估模組
5-8-NL-LOGIC-EVM — 支援 5 至 8 針腳 DPW、DQE、DRY、DSF、DTM、DTQ 和 DTT 封裝的通用邏輯和轉譯 EVM
支援任何具 DTT、DRY、DPW、DTM、DQE、DQM、DSF 或 DTQ 封裝的邏輯或轉換裝置之通用 EVM。可實現靈活評估的電路板設計。
AVCLVCDIRCNTRL-EVM — 適用於方向控制雙向轉換裝置、支援 AVC 和 LVC 的通用 EVM
通用 EVM 的設計可支援一、二、四、八通道 LVC 及 AVC 方向控制的轉換裝置。此外也支援相同通道數量的匯流排保留與汽車 -Q1 裝置。AVC 是低電壓轉換裝置,具較低驅動強度 12mA。LVC 是較高的電壓轉換裝置,範圍從 1.65 到 5.5V 且具較高驅動強度 32mA。
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| VSSOP (DCU) | 8 | Ultra Librarian |
| X1QFN (DTT) | 8 | Ultra Librarian |
訂購與品質
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中持續性的可靠性監測
- 晶圓廠位置
- 組裝地點