首頁 音訊、觸覺和壓電 音訊放大器 車用音訊放大器
首頁
音訊、觸覺和壓電
音訊放大器
車用音訊放大器

TPA2000D1-Q1

現行

車用 2-W、類比輸入單聲道 D 類音訊放大器

立即訂購
產品規格表

TPA2000D1-Q1

現行
產品規格表 立即訂購

產品詳細資料

Output power (W) 2 Power stage supply (max) (V) 5.5 Power stage supply (min) (V) 2.7 Speaker channels (max) Mono Features ESD Protection Audio input type Analog Input Control interface GPIO THD + N at 1 kHz (%) 0.2 Switching frequency (max) (Hz) 300000 Output noise voltage (µV) 40 Rating Automotive Operating temperature range (°C) -40 to 105
Output power (W) 2 Power stage supply (max) (V) 5.5 Power stage supply (min) (V) 2.7 Speaker channels (max) Mono Features ESD Protection Audio input type Analog Input Control interface GPIO THD + N at 1 kHz (%) 0.2 Switching frequency (max) (Hz) 300000 Output noise voltage (µV) 40 Rating Automotive Operating temperature range (°C) -40 to 105
TSSOP (PW) 16 32 mm² (5 mm × 6.4 mm)
  • Qualified for Automotive Applications
  • ESD Protection Exceeds 2000 V Per MIL-STD-883, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0)
  • Modulation Scheme Optimized to Operate Without a Filter
  • Extremely Efficient Third-Generation 5-V Class-D Technology:
    • Low Supply Current (No Filter) . . . 4 mA
    • Low Supply Current (Filter) . . . 7.5 mA
    • Low Shutdown Current . . . 0.05 µA
    • Low-Noise Floor . . . 40 µVRMS (No-Weighting Filter)
    • Maximum Efficiency Into 8 Ω, 75 — 85%
    • Four Internal Gain Settings . . . 6 — 23.5 dB
    • PSSR . . . –77 dB
  • 4 mm × 4 mm MicroStar™ Junior BGA and TSSOP Package Options
  • 2 W Into a 4-Ω Speaker (THD+N<1%)
  • <0.2% THD+N at 1.5 W, 1 kHz, Into a 4-Ω Load
  • Integrated Depop Circuitry
  • Short-Circuit Protection (Short to PVDD, Ground, and Load)

MicroStar is a trademark of Texas Instruments.
  • Qualified for Automotive Applications
  • ESD Protection Exceeds 2000 V Per MIL-STD-883, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0)
  • Modulation Scheme Optimized to Operate Without a Filter
  • Extremely Efficient Third-Generation 5-V Class-D Technology:
    • Low Supply Current (No Filter) . . . 4 mA
    • Low Supply Current (Filter) . . . 7.5 mA
    • Low Shutdown Current . . . 0.05 µA
    • Low-Noise Floor . . . 40 µVRMS (No-Weighting Filter)
    • Maximum Efficiency Into 8 Ω, 75 — 85%
    • Four Internal Gain Settings . . . 6 — 23.5 dB
    • PSSR . . . –77 dB
  • 4 mm × 4 mm MicroStar™ Junior BGA and TSSOP Package Options
  • 2 W Into a 4-Ω Speaker (THD+N<1%)
  • <0.2% THD+N at 1.5 W, 1 kHz, Into a 4-Ω Load
  • Integrated Depop Circuitry
  • Short-Circuit Protection (Short to PVDD, Ground, and Load)

MicroStar is a trademark of Texas Instruments.

The TPA2000D1 is a 2-W mono bridge-tied-load (BTL) class-D amplifier designed to drive a speaker with at least 4-Ω impedance. The amplifier uses Texas Instruments third-generation modulation technique, which results in improved efficiency and SNR. It also allows the device to be connected directly to the speaker without the use of the LC output filter commonly associated with class-D amplifiers (this results in EMI which must be shielded at the system level). These features make the device ideal for use in devices where high efficiency is needed to extend battery run time.

The gain of the amplifier is controlled by two input terminals, GAIN1 and GAIN0. This allows the amplifier to be configured for a gain of 6, 12, 18, and 23.5 dB. The differential input terminals are high-impedance CMOS inputs and can be used as summing nodes.

The class-D BTL amplifier includes depop circuitry to reduce the amount of turnon pop at power up and when cycling SHUTDOWN.

The TPA2000D1 is available in the 16-pin TSSOP and MicroStar™ Junior BGA packages and drive 2 W of continuous output power into a 4-Ω load. The TPA2000D1T operates over an ambient temperature range of –40°C to 105°C.

The TPA2000D1 is a 2-W mono bridge-tied-load (BTL) class-D amplifier designed to drive a speaker with at least 4-Ω impedance. The amplifier uses Texas Instruments third-generation modulation technique, which results in improved efficiency and SNR. It also allows the device to be connected directly to the speaker without the use of the LC output filter commonly associated with class-D amplifiers (this results in EMI which must be shielded at the system level). These features make the device ideal for use in devices where high efficiency is needed to extend battery run time.

The gain of the amplifier is controlled by two input terminals, GAIN1 and GAIN0. This allows the amplifier to be configured for a gain of 6, 12, 18, and 23.5 dB. The differential input terminals are high-impedance CMOS inputs and can be used as summing nodes.

The class-D BTL amplifier includes depop circuitry to reduce the amount of turnon pop at power up and when cycling SHUTDOWN.

The TPA2000D1 is available in the 16-pin TSSOP and MicroStar™ Junior BGA packages and drive 2 W of continuous output power into a 4-Ω load. The TPA2000D1T operates over an ambient temperature range of –40°C to 105°C.
filter 尋找其它 車用音訊放大器
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
功能相同，但針腳輸出與所比較的裝置不同。
TAS2505A-Q1 現行 具音訊處理功能的車用 2-W、單聲道、數位或類比輸入 D 類放大器 Analog and digital input support

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 4
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 2-W Filterless Mono Class-D Audio Power Amplifier datasheet (Rev. E) 2008/10/31
應用說明 Guidelines for Measuring Audio Power Amplifier Performance (Rev. A) 2019/8/26
應用說明 AN-1849 An Audio Amplifier Power Supply Design (Rev. C) 2019/6/27
應用說明 AN-1737 Managing EMI in Class D Audio Applications (Rev. A) 2013/5/1

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

封裝 針腳 CAD 符號、佔位空間與 3D 模型
TSSOP (PW) 16 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片