SBOS671D September   2018  – December 2022 OPA2828 , OPA828

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Phase-Reversal Protection
      2. 7.3.2  Electrical Overstress
      3. 7.3.3  MUX Friendly Inputs
      4. 7.3.4  Overload Power Limiter
      5. 7.3.5  Noise Performance
        1. 7.3.5.1 Low Noise
      6. 7.3.6  Capacitive Load and Stability
      7. 7.3.7  Settling Time
      8. 7.3.8  Slew Rate
      9. 7.3.9  Full-Power Bandwidth
      10. 7.3.10 Small-Signal Response
      11. 7.3.11 Thermal Shutdown
      12. 7.3.12 Low Offset Voltage Drift
      13. 7.3.13 Overload Recovery
    4. 7.4 Device Functional Modes
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 SAR ADC Driver
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Application Curves
      2. 8.2.2 Low-Pass Filter
        1. 8.2.2.1 Design Requirements
        2. 8.2.2.2 Detailed Design Procedure
        3. 8.2.2.3 Application Curve
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
        1. 8.4.1.1 Thermal Considerations
        2. 8.4.1.2 PowerPAD™ Design Considerations (DGN package only)
      2. 8.4.2 Layout Example
  9. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Development Support
        1. 9.1.1.1 PSpice® for TI
        2. 9.1.1.2 Filter Design Tool
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 Receiving Notification of Documentation Updates
    4. 9.4 Support Resources
    5. 9.5 Trademarks
    6. 9.6 Electrostatic Discharge Caution
    7. 9.7 Glossary
  10. 10Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

6.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)(1)
MIN MAX UNIT
VS Supply voltage, (V+) – (V–) Single-supply 40 V
Dual-supply ±20
Signal input pins Voltage Common-mode(3) (V–) – 0.5 (V+) + 0.5 V
Differential(2) (V+) – (V–)
Current(3) ±10 mA
Output short current(4) Continuous
Thermal pad voltage (DGN package) (V–) – 1 (V–) + 30 V
TJ Junction temperature(5) -55 150 °C
Tstg Storage temperature –65 150
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Ratings. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) Input terminals are not clamped to each other with anti-parallel diodes. The JFET input stage allows large differential voltage values up to the supply voltage of the device.
(3) Input terminals are diode-clamped to the power-supply rails. Current-limit input signals that can swing more than 0.5 V beyond the supply rails to 10 mA or less.
(4) Short circuit to ground, one amplifier per package.
(5) For information on device ambient and junction temperatures, see Section 8.4.1.1 and Section 7.3.11.