LM51772
55V wide VIN four-switch buck-boost controller with I2C interface
LM51772
- Input range from 3.5V to 55V
- Output voltage 3.3V to 55V
- Dynamical Vo programming via I2C from 3.3V
- up to 48V in 20mV monotonous steps
- up to 24V in 10mV monotonous steps
- Peak current regulation scheme
- Small voltage transition ripple over all operating modes
- Dynamic output voltage tracking (digital PWM tracking input, analog tracking input)
- Via I2C interface programming
- Shut down quiescent current 3µA
- Operating quiescent current 60µA
- DRV pin for external FET control
- Operation mode selection for high efficiency in light load and high load conditions:
- Power save mode (burst/µSleep)
- Automatic/programmable conduction mode
- Integrated high voltage supply LDO
- Axillary high voltage LDO/reference
- Integrated full-bridge gate drive
- 2A peak current capability
- Bootstrap over and under-voltage protection
- Integrated boot-strap diode
- Fixed frequency independent from operating mode (boost, buck-boost, buck)
- Forced PWM mode selectable
- Switching frequency from 100kHz to 2.2MHz
- External clock synchronization and clock output
- Spread spectrum operation selectable
- High-side output current sensor
- Programmable from 1A to 7A in 50mA steps
- ISET pin selectable
- I2C Interface readout of (device configuration, enhanced monitoring features, programmable thermal warning)
-
Create a custom design using the LM51772 with the WEBENCH® Power Designer
The LM51772 is a four switch Buck-Boost controller. It provides a regulated output voltage if the input voltage is higher, equal or lower than the adjusted output voltage. In power save mode the device supports very high efficiency over the complete operation range of the output. The LM51772 runs at a fixed switching frequency, which can be set via the RT/SYNC pin. The switching frequency remains constant during buck, boost and buck-boost operation in forced PWM. The external compensation pin allows very fast transient responds for different applications.(Continued)
Technische Dokumentation
Typ | Titel | Datum | ||
---|---|---|---|---|
* | Data sheet | LM51772 55V 4-Switch Buck-Boost Controller with I2 C interface datasheet (Rev. A) | PDF | HTML | 21 Mär 2024 |
Application note | Layout Optimization of 4-Switch Buck-Boost Converters | PDF | HTML | 05 Sep 2023 |
Design und Entwicklung
Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.
LM51772EVM-HP — Evaluierungsmodul LM51772
Das LM51772EVM-HP zeigt ein flexibles, leistungsstarkes Abwärts-/Aufwärts-Design unter Verwendung des Abwärts-/Aufwärts-Controllers LM51772 mit großem VIN-Eingangsspannungsbereich. Das Evaluierungsmodul ist für den Betrieb im Eingangsspannungsbereich von 9 V bis 48 V konfiguriert und bietet einen (...)
USB2ANY — USB2ANY-Schnittstellenadapter
The USB2ANY interface adapter is a tool intended to allow a computer to control an evaluation module (EVM) via a USB connection. USB2ANY supports multiple popular protocol interfaces and provides 3.3-V and 5-V power supplies.
LM51772-QUICKSTART-CALC — LM51772 BuckBoost Quickstart Calculator Tool
Unterstützte Produkte und Hardware
Produkte
AC/DC & DC/DC controllers (external FET)
Hardware-Entwicklung
Evaluierungsplatine
Gehäuse | Pins | Herunterladen |
---|---|---|
VQFN (RHA) | 40 | Optionen anzeigen |
Bestellen & Qualität
- RoHS
- REACH
- Bausteinkennzeichnung
- Blei-Finish/Ball-Material
- MSL-Rating / Spitzenrückfluss
- MTBF-/FIT-Schätzungen
- Materialinhalt
- Qualifikationszusammenfassung
- Kontinuierliches Zuverlässigkeitsmonitoring
- Werksstandort
- Montagestandort
Support und Schulungen
TI E2E™-Foren mit technischem Support von TI-Ingenieuren
Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.
Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support.