SLASFD8 May   2025 TAS5830

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Typical Characteristics
      1. 5.7.1 Bridge Tied Load (BTL) Configuration Curves with BD Modulation
      2. 5.7.2 Bridge Tied Load (BTL) Configuration Curves with 1SPW Modulation
      3. 5.7.3 Parallel Bridge Tied Load (PBTL) Configuration With BD Modulation
      4. 5.7.4 Parallel Bridge Tied Load (PBTL) Configuration With 1SPW Modulation
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Power Supplies
      2. 6.3.2 Device Clocking
      3. 6.3.3 Serial Audio Port – Clock Rates
      4. 6.3.4 Clock Halt Auto-recovery
      5. 6.3.5 Sample Rate on the Fly Change
      6. 6.3.6 Serial Audio Port - Data Formats and Bit Depths
    4. 6.4 Device Functional Modes
      1. 6.4.1 Software Control
      2. 6.4.2 Speaker Amplifier Operating Modes
        1. 6.4.2.1 BTL Mode
        2. 6.4.2.2 PBTL Mode
      3. 6.4.3 Low EMI Modes
        1. 6.4.3.1 Spread Spectrum
        2. 6.4.3.2 Channel to Channel Phase Shift
        3. 6.4.3.3 Multi-Devices PWM Phase Synchronization
          1. 6.4.3.3.1 Phase Synchronization With I2S Clock In Startup Phase
          2. 6.4.3.3.2 Phase Synchronization With GPIO
      4. 6.4.4 Thermal Foldback
      5. 6.4.5 Device State Control
      6. 6.4.6 Device Modulation
        1. 6.4.6.1 BD Modulation
        2. 6.4.6.2 1SPW Modulation
        3. 6.4.6.3 Hybrid Modulation
      7. 6.4.7 Programming and Control
        1. 6.4.7.1 I2C Serial Communication Bus
        2. 6.4.7.2 Hardware Control Mode
        3. 6.4.7.3 I2C Target Address
          1. 6.4.7.3.1 Random Write
          2. 6.4.7.3.2 Sequential Write
          3. 6.4.7.3.3 Random Read
          4. 6.4.7.3.4 Sequential Read
          5. 6.4.7.3.5 DSP Memory Book, Page and BQ update
          6. 6.4.7.3.6 Checksum
            1. 6.4.7.3.6.1 Cyclic Redundancy Check (CRC) Checksum
            2. 6.4.7.3.6.2 Exclusive or (XOR) Checksum
        4. 6.4.7.4 Control via Software
          1. 6.4.7.4.1 Startup Procedures
          2. 6.4.7.4.2 Shutdown Procedures
        5. 6.4.7.5 Protection and Monitoring
          1. 6.4.7.5.1 Overcurrent Limit (Cycle-By-Cycle)
          2. 6.4.7.5.2 Overcurrent Shutdown (OCSD)
          3. 6.4.7.5.3 DC Detect Error
          4. 6.4.7.5.4 Overtemperature Shutdown (OTSD)
          5. 6.4.7.5.5 PVDD Overvoltage and Undervoltage Error
          6. 6.4.7.5.6 PVDD Drop Detection
          7. 6.4.7.5.7 Clock Fault
  8. 7 Register Maps
    1. 7.1 reg_map Registers
  9. 8 Application and Implementation
    1. 8.1 Typical Applications
      1. 8.1.1 2.0 (Stereo BTL) System
      2. 8.1.2 Mono (PBTL) Systems
    2. 8.2 Power Supply Recommendations
      1. 8.2.1 DVDD Supply
      2. 8.2.2 PVDD Supply
    3. 8.3 Layout
      1. 8.3.1 Layout Guidelines
        1. 8.3.1.1 General Guidelines for Audio Amplifiers
        2. 8.3.1.2 Importance of PVDD Bypass Capacitor Placement on PVDD Network
        3. 8.3.1.3 Optimizing Thermal Performance
      2. 8.3.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Device Nomenclature
      2. 9.1.2 Development Support
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.2.1 DVDD Supply

The DVDD supply that is required from the system is used to power several portions of the device. As shown in Power Supply Functional Block Diagram, the DVDD supply provides power to the DVDD pin. Proper connection, routing and decoupling techniques are highlighted in the Section 8 section and the Section 8.3.2 section and must be followed as closely as possible for proper operation and performance.

Some portions of the device also require a separate power supply that is a lower voltage than the DVDD supply. To simplify the power supply requirements for the system, the TAS5830 device includes an integrated low dropout (LDO) linear regulator to create this supply. This linear regulator is internally connected to the DVDD supply and the output is presented on the DVDD_REG pin, providing a connection point for an external bypass capacitor. Note that the linear regulator integrated in the device has only been designed to support the current requirements of the internal circuitry, and is not to be used to power any additional external circuity. Additional loading on this pin can cause the voltage to sag, negatively affecting the performance and operation of the device.