SLVSET9G September   2018  – April 2026 TPS1663

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Hot Plug-In and In-Rush Current Control
        1. 8.3.1.1 Thermal Regulation Loop
      2. 8.3.2  Undervoltage Lockout (UVLO)
      3. 8.3.3  Overvoltage Protection (OVP)
      4. 8.3.4  Overload and Short Circuit Protection
        1. 8.3.4.1 Overload Protection
        2. 8.3.4.2 Short Circuit Protection
          1. 8.3.4.2.1 Start-Up With Short-Circuit On Output
      5. 8.3.5  Output Power Limiting, PLIM (TPS16632 and TPS16637)
      6. 8.3.6  Current Monitoring Output (IMON)
      7. 8.3.7  FAULT Response (FLT)
      8. 8.3.8  Power Good Output (PGOOD)
      9. 8.3.9  IN, P_IN, OUT and GND Pins
      10. 8.3.10 Thermal Shutdown
      11. 8.3.11 Low Current Shutdown Control (SHDN)
    4. 8.4 Device Functional Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Programming the Current-Limit Threshold R(ILIM) Selection
        2. 9.2.2.2 Undervoltage Lockout and Overvoltage Set Point
        3. 9.2.2.3 Setting Output Voltage Ramp Time (tdVdT)
          1. 9.2.2.3.1 Support Component Selections RPGOOD and C(IN)
      3. 9.2.3 Application Curves
    3. 9.3 System Examples
      1. 9.3.1 Simple 24V Power Supply Path Protection
    4. 9.4 Power Supply Recommendations
      1. 9.4.1 Transient Protection
    5. 9.5 Layout
      1. 9.5.1 Layout Guidelines
      2. 9.5.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.3.1 Hot Plug-In and In-Rush Current Control

The devices are designed to control the in-rush current upon insertion of a card into a live backplane or other hot power source. This design limits the voltage sag on the backplane supply voltage and prevents unintended resets of the system power. The controlled start-up also helps to eliminate conductive and radiative interferences. An external capacitor connected from the dVdT pin to GND defines the slew rate of the output voltage at power-on. The fastest output slew rate of 24V/500µs can be achieved by leaving dVdT pin floating. The inrush current can be calculated using Equation 1.

Equation 1. I = C × d V d T ≥ I I N R U S H = C O U T × V I N t d V d T

where

Equation 2. t d V d T = 20.8 × 10 3 × V I N × C d V d T

Figure 8-1 illustrates in-rush current control performance of the device during Hot Plug-In.

TPS1663 Hot Plug In and In-Rush Current Control at 24V Input
CdVdT = 100nFCOUT = 1000µFRILIM = 4.02kΩ
Figure 8-1 Hot Plug In and In-Rush Current Control at 24V Input