SLVSET9G September   2018  – April 2026 TPS1663

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Hot Plug-In and In-Rush Current Control
        1. 8.3.1.1 Thermal Regulation Loop
      2. 8.3.2  Undervoltage Lockout (UVLO)
      3. 8.3.3  Overvoltage Protection (OVP)
      4. 8.3.4  Overload and Short Circuit Protection
        1. 8.3.4.1 Overload Protection
        2. 8.3.4.2 Short Circuit Protection
          1. 8.3.4.2.1 Start-Up With Short-Circuit On Output
      5. 8.3.5  Output Power Limiting, PLIM (TPS16632 and TPS16637)
      6. 8.3.6  Current Monitoring Output (IMON)
      7. 8.3.7  FAULT Response (FLT)
      8. 8.3.8  Power Good Output (PGOOD)
      9. 8.3.9  IN, P_IN, OUT and GND Pins
      10. 8.3.10 Thermal Shutdown
      11. 8.3.11 Low Current Shutdown Control (SHDN)
    4. 8.4 Device Functional Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Programming the Current-Limit Threshold R(ILIM) Selection
        2. 9.2.2.2 Undervoltage Lockout and Overvoltage Set Point
        3. 9.2.2.3 Setting Output Voltage Ramp Time (tdVdT)
          1. 9.2.2.3.1 Support Component Selections RPGOOD and C(IN)
      3. 9.2.3 Application Curves
    3. 9.3 System Examples
      1. 9.3.1 Simple 24V Power Supply Path Protection
    4. 9.4 Power Supply Recommendations
      1. 9.4.1 Transient Protection
    5. 9.5 Layout
      1. 9.5.1 Layout Guidelines
      2. 9.5.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information
8.3.4.2.1 Start-Up With Short-Circuit On Output

When the device is started with short-circuit on the output, the current begins to limit at I(OL). Due to high power dissipation of VIN × I(OL) within the device the junction temperature increases. Subsequently, the thermal regulation control loop limits the load current to regulate the junction temperature at T(J_REG), 145°C (typical) for a duration of t(Treg_timeout), 1.25 sec (typical). Subsequent operation of the device depends on the MODE configuration (auto-retry or latch off) setting as per the Table 8-1. FLT gets asserted after t(Treg_timeout) and remains asserted until the output short-circuit is removed. Figure 8-9 illustrates the behavior of the device in this condition.

TPS1663 Start-Up With Short on Output
VIN = 24V RILIM = 3kΩ
Figure 8-9 Start-Up With Short on Output