SBASAW5 December   2025 ADS122C14

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 I2C Timing Requirements
    7. 5.7 I2C Switching Characteristics
    8. 5.8 Timing Diagrams
    9. 5.9 Typical Characteristics
  7. 6 Parameter Measurement Information
    1. 6.1 Noise Performance
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Analog Inputs and Multiplexer
      2. 7.3.2  Programmable Gain Amplifier (PGA)
      3. 7.3.3  Voltage Reference
        1. 7.3.3.1 Internal Reference
        2. 7.3.3.2 External Reference
        3. 7.3.3.3 Reference Buffers
      4. 7.3.4  Clock Source
      5. 7.3.5  Delta-Sigma Modulator
      6. 7.3.6  Digital Filter
        1. 7.3.6.1 Sinc4 and Sinc4 + Sinc1 Filter
        2. 7.3.6.2 FIR Filter
        3. 7.3.6.3 Digital Filter Latency
        4. 7.3.6.4 Global-Chop Mode
      7. 7.3.7  Excitation Current Sources (IDACs)
      8. 7.3.8  Burn-Out Current Sources (BOCS)
      9. 7.3.9  General Purpose IOs (GPIOs)
        1. 7.3.9.1 FAULT Output
        2. 7.3.9.2 DRDY Output
      10. 7.3.10 System Monitors
        1. 7.3.10.1 Internal Short (Offset Calibration)
        2. 7.3.10.2 Internal Temperature Sensor
        3. 7.3.10.3 External Reference Voltage Readback
        4. 7.3.10.4 Power-Supply Readback
      11. 7.3.11 Monitors and Status Flags
        1. 7.3.11.1 Reset (RESETn flag)
        2. 7.3.11.2 AVDD Undervoltage Monitor (AVDD_UVn flag)
        3. 7.3.11.3 Reference Undervoltage Monitor (REV_UVn flag)
        4. 7.3.11.4 Register Map CRC Fault (REG_MAP_CRC_FAULTn flag)
        5. 7.3.11.5 Internal Memory Fault (MEM_FAULTn flag)
        6. 7.3.11.6 Register Write Fault (REG_WRITE_FAULTn flag)
        7. 7.3.11.7 DRDY Indicator (DRDY bit)
        8. 7.3.11.8 Conversion Counter (CONV_COUNT[3:0])
    4. 7.4 Device Functional Modes
      1. 7.4.1 Power-up and Reset
        1. 7.4.1.1 Power-On Reset (POR)
        2. 7.4.1.2 Reset by Register Write
        3. 7.4.1.3 I2C General Call Reset
      2. 7.4.2 Operating Modes
        1. 7.4.2.1 Idle and Standby Mode
        2. 7.4.2.2 Power-Down Mode
        3. 7.4.2.3 Power-Scalable Conversion Modes
          1. 7.4.2.3.1 Continuous-Conversion Mode
          2. 7.4.2.3.2 Single-shot Conversion Mode
    5. 7.5 Programming
      1. 7.5.1  I2C Interface
      2. 7.5.2  I2C Address
      3. 7.5.3  Serial Clock (SCL) and Serial Data (SDA)
      4. 7.5.4  I2C Bus Speed
      5. 7.5.5  I2C Data Transfer Protocol
      6. 7.5.6  I2C General Call (Software Reset)
      7. 7.5.7  I3C Compatibility
      8. 7.5.8  Commands
        1. 7.5.8.1 RDATA (0000 0000b)
        2. 7.5.8.2 RREG (0100 rrrrb)
        3. 7.5.8.3 WREG (1000 rrrrb)
      9. 7.5.9  STATUS Header
      10. 7.5.10 I2C CRC
      11. 7.5.11 Register Map CRC
      12. 7.5.12 Data Ready (DRDY) Pin
      13. 7.5.13 Monitoring for New Conversion Data
        1. 7.5.13.1 DRDY Pin Monitoring
        2. 7.5.13.2 Reading DRDY Bit and Conversion Counter
        3. 7.5.13.3 Clock Counting
      14. 7.5.14 Conversion Data Format
  9. 8 Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Serial Interface Connections
      2. 9.1.2 Connecting Multiple Devices on the Same I2C Bus
      3. 9.1.3 Unused Inputs and Outputs
      4. 9.1.4 Device Initialization
    2. 9.2 Typical Applications
      1. 9.2.1 Software-Configurable RTD Measurement Input
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
        3. 9.2.1.3 Application Performance Plots
        4. 9.2.1.4 Design Variant – 3-Wire RTD Measurement With Automatic Lead-Wire Compensation Using Two IDACs
      2. 9.2.2 Thermocouple Measurement With Cold-Junction Compensation Using a 2-wire RTD
      3. 9.2.3 Resistive Bridge Sensor Measurement With Temperature Compensation
    3. 9.3 Power Supply Recommendations
      1. 9.3.1 Power Supplies
      2. 9.3.2 Power-Supply Sequencing
      3. 9.3.3 Power-Supply Decoupling
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

4 Pin Configuration and Functions

ADS112C14 ADS122C14 ADS1x2C14, RTE Package,16-pin WQFN, Top ViewFigure 4-1 ADS1x2C14, RTE Package,
16-pin WQFN, Top View
ADS112C14 ADS122C14 ADS1x2C14, YBH Package,16-pin DSBGA, Top ViewFigure 4-2 ADS1x2C14, YBH Package,
16-pin DSBGA, Top View
Table 4-1 ADS1x2C14 Pin Functions
PIN TYPE DESCRIPTION(1)
NAME RTE YBH
A0 9 C2 Digital Input I2C target address select pin 0. See the I2C Address section for details.(5)
A1 10 D1 Digital Input I2C target address select pin 1. See the I2C Address section for details.(5)
AIN0 1 A4 Analog Input Analog input 0
AIN1 2 B4 Analog Input Analog input 1
AIN2 3 C4 Analog Input Analog input 2
AIN3 4 D4 Analog Input Analog input 3
AIN4/REFP/
GPIO0		 5 B3 Analog Input/
Digital IO		 Analog input 4. Positive external reference input.
General purpose digital input/output 0.(2) (4)
AIN5/REFN/
GPIO1		 6 C3 Analog Input/
Digital IO		 Analog input 5. Negative external reference input.
General purpose digital input/output 1.(2) (4)
AIN6/
GPIO2/FAULT		 7 D3 Analog Input/
Digital IO		 Analog input 6.
General purpose digital input/output 2.(2) (4)
Pin can be configured as dedicated FAULT output.
AIN7/
GPIO3/DRDY/CLK		 8 D2 Analog Input/
Digital IO		 Analog input 7.
General purpose digital input/output 3.(2) (4)
Pin can be configured as dedicated DRDY output or external clock input.
AVDD 15 A2 Analog Supply Positive analog supply. Connect a 100nF capacitor to GND.
DVDD 13 A1 Digital Supply Digital supply. Connect a 100nF capacitor to GND.
GND 14 B2 Ground Ground
REFOUT 16 A3 Analog Output Internal voltage reference output. Connect a 100nF capacitor to GND.
SCL 12 B1 Digital Input Serial clock input. Connect to DVDD using a pullup resistor.(5)
SDA 11 C1 Digital Output Serial data input and output. Connect to DVDD using a pullup resistor. (3)(5)
Thermal Pad - N/A - Thermal power pad. Connect to GND.
(1) See the Unused Inputs and Outputs section for details on how to connect unused pins.
(2) Configurable as push-pull or open-drain output.
(3) Open-drain output.
(4) Logic levels referenced to AVDD.
(5) Logic levels referenced to DVDD.