SCDS453E June   2024  – October 2025 TMUXS7614D

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Thermal Information
    4. 5.4  Recommended Operating Conditions
    5. 5.5  Source or Drain Current through Switch
    6. 5.6  Electrical Characteristics (Global)
    7. 5.7  Electrical Characteristics (±15V Dual Supply)
    8. 5.8  Switching Characteristics (±15V Dual Supply)
    9. 5.9  Electrical Characteristics (±20V Dual Supply)
    10. 5.10 Switching Characteristics (±20V Dual Supply)
    11. 5.11 Electrical Characteristics (+37.5V/–12.5V Dual Supply)
    12. 5.12 Switching Characteristics (+37.5V/–12.5V Dual Supply)
    13. 5.13 Electrical Characteristics (12V Single Supply)
    14. 5.14 Switching Characteristics (12V Single Supply)
    15. 5.15 SPI Timing Characteristics (2.7V to 5.5V)
    16. 5.16 SPI Timing Characteristics (1.8V to 2.7V)
    17. 5.17 Timing Diagrams
    18. 5.18 Typical Characteristics
  7. 6 Parameter Measurement Information
    1. 6.1  On-Resistance
    2. 6.2  Off-Leakage Current
    3. 6.3  On-Leakage Current
    4. 6.4  tON and tOFF Time
    5. 6.5  Break-Before-Make
    6. 6.6  Charge Injection
    7. 6.7  Off Isolation
    8. 6.8  Channel-to-Channel Crosstalk
    9. 6.9  Bandwidth
    10. 6.10 THD + Noise
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Bidirectional Operation
      2. 7.3.2 Rail-to-Rail Operation
      3. 7.3.3 1.8V Logic Compatible Inputs
      4. 7.3.4 Flat On-Resistance
      5. 7.3.5 Power-Up Sequence Free
    4. 7.4 SPI Operation
      1. 7.4.1 Address Mode
      2. 7.4.2 Burst Mode
      3. 7.4.3 Daisy Chain Mode
      4. 7.4.4 Error Detection
        1. 7.4.4.1 Address R/W Error Flag
        2. 7.4.4.2 SCLK Count Error Flag
        3. 7.4.4.3 CRC (Cyclic Redundancy Check) Enable and Error Flag
        4. 7.4.4.4 Clearing Error Flags
      5. 7.4.5 Software Reset
    5. 7.5 Device Functional Modes
    6. 7.6 Register Map
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curve
    3. 8.3 Recommended Reflow Profile
    4. 8.4 Thermal Considerations
    5. 8.5 Power Supply Recommendations
    6. 8.6 Layout
      1. 8.6.1 Layout Guidelines
      2. 8.6.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information
    1. 11.1 Tape and Reel Information
    2. 11.2 Mechanical Data

5.4 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN NOM MAX UNIT
VDD – VSS(1) Power supply voltage differential 4.5 50 V
VDD Positive power supply voltage 4.5 42 V
VS or VD Signal path input/output voltage (source or drain pin) (Sx, D) VSS VDD V
VL Logic Supply Voltage 1.8 5.5 V
VLOGIC Logic control input pin voltage (SPI pins) 0 5.5 V
IS or ID (CONT) Source or drain continuous current (Sx, D) IDC(2) mA
TA Ambient temperature –40 125 °C
(1) VDD and VSS can be any value within maximum recommended operating conditions as long as 4.5V ≤ (VDD – VSS) ≤ 44V and the minimum VDD is met.
(2) Refer to Source or Drain Continuous Current table for IDC specifications.