SCDS461A November   2023  – January 2025 TMUX7348F-EP

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Thermal Information
    4. 6.4  Recommended Operating Conditions
    5. 6.5  Electrical Characteristics (Global)
    6. 6.6  ±15V Dual Supply: Electrical Characteristics
    7. 6.7  ±20 V Dual Supply: Electrical Characteristics
    8. 6.8  12 V Single Supply: Electrical Characteristics
    9. 6.9  36 V Single Supply: Electrical Characteristics
    10. 6.10 Typical Characteristics
  8. 7 Parameter Measurement Information
    1. 7.1  On-Resistance
    2. 7.2  Off-Leakage Current
    3. 7.3  On-Leakage Current
    4. 7.4  Input and Output Leakage Current Under Overvoltage Fault
    5. 7.5  Break-Before-Make Delay
    6. 7.6  Enable Delay Time
    7. 7.7  Transition Time
    8. 7.8  Fault Response Time
    9. 7.9  Fault Recovery Time
    10. 7.10 Fault Flag Response Time
    11. 7.11 Fault Flag Recovery Time
    12. 7.12 Charge Injection
    13. 7.13 Off Isolation
    14. 7.14 Crosstalk
    15. 7.15 Bandwidth
    16. 7.16 THD + Noise
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Flat ON- Resistance
      2. 8.3.2 Protection Features
        1. 8.3.2.1 Input Voltage Tolerance
        2. 8.3.2.2 Powered-Off Protection
        3. 8.3.2.3 Fail-Safe Logic
        4. 8.3.2.4 Overvoltage Protection and Detection
        5. 8.3.2.5 Adjacent Channel Operation During Fault
        6. 8.3.2.6 ESD Protection
        7. 8.3.2.7 Latch-Up Immunity
        8. 8.3.2.8 EMC Protection
      3. 8.3.3 Overvoltage Fault Flags
      4. 8.3.4 Bidirectional and Rail-to-Rail Operation
      5. 8.3.5 1.8 V Logic Compatible Inputs
      6. 8.3.6 Integrated Pull-Down Resistor on Logic Pins
    4. 8.4 Device Functional Modes
      1. 8.4.1 Normal Mode
      2. 8.4.2 Fault Mode
      3. 8.4.3 Truth Tables
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

6.6 ±15V Dual Supply: Electrical Characteristics

VDD = +15V ± 10%, VSS = –15V ±10%, GND = 0V (unless otherwise noted) 
Typical at VDD = +15V, VSS = –15V, TA = 25℃  (unless otherwise noted)
PARAMETER TEST CONDITIONS TA MIN TYP MAX UNIT
ANALOG SWITCH
RON On-resistance VS = –10V to +10V,
IS = –1mA		 25°C 180 250 Ω
–40°C to +85°C 330
–55°C to +125°C 390
ΔRON On-resistance mismatch between channels VS = –10V to +10V,
IS = –1mA		 25°C 2.5 8 Ω
–40°C to +85°C 12
–55°C to +125°C 13
RFLAT On-resistance flatness VS = –10V to +10V,
IS = –1mA		 25°C 1.5 3.5 Ω
–40°C to +85°C 4
–55°C to +125°C 4
RON_DRIFT On-resistance drift VS = 0V, IS = –1mA –55°C to +125°C 1.2 Ω/°C
IS(OFF) Source off leakage current(1) VDD = 16.5V, VSS = –16.5V
Switch state is off
VS = +10V / –10V
VD = –10V / + 10V		 25°C –1 0.1 1 nA
–40°C to +85°C –1 1
–55°C to +125°C –4 4
ID(OFF) Drain off leakage current(1) VDD = 16.5V, VSS = –16.5V
Switch state is off
VS = +10V / –10V
VD = –10V / + 10V		 25°C –1 0.1 1 nA
–40°C to +85°C –3 3
–55°C to +125°C –14 14
IS(ON)
ID(ON)		 Output on leakage current(2) VDD = 16.5V, VSS = –16.5V
Switch state is on
VS = VD = ±10V		 25°C –1.5 0.3 1.5 nA
–40°C to +85°C –5 5
–55°C to +125°C –22 22
FAULT CONDITION
IS(FA) Input leakage current
durring overvoltage		 VS = ± 60V, GND = 0V,
VDD = VFP = 16.5V, VSS = VFN =  –16.5V		 –55°C to +125°C ±110 µA
IS(FA) Grounded Input leakage current
during overvoltage with
grounded supply voltages		 VS = ± 60V, GND = 0V,
VDD = VSS = VFP = VFN= 0V		 –55°C to +125°C ±135 µA
IS(FA) Floating Input leakage current
during overvoltage with
floating supply voltages		 VS = ± 60V, GND = 0V,
VDD = VSS = VFP = VFN= floating		 –55°C to +125°C ±135 µA
ID(FA) Output leakage current
during overvoltage		 VS = ± 60V, GND = 0V,
VDD = VFP = 16.5V, VSS = VFN =  –16.5V,
–15.5V ≤ VD ≤ 16.5V		 25°C –50 ±10 50 nA
–40°C to +85°C –70 70
–55°C to +125°C –90 90
ID(FA) Grounded Output leakage current
during overvoltage with
grounded supply voltages		 VS = ± 60V, GND = 0V,
VDD = VSS = VFP = VFN= 0V		 25°C –50 ±1 50 nA
–40°C to +85°C –100 100
–55°C to +125°C –500 500
ID(FA) Floating Output leakage current
during overvoltage with
floating supply voltages		 VS = ± 60V, GND = 0V,
VDD = VSS = VFP = VFN= floating		 25°C ±3 µA
–40°C to +85°C ±5
–55°C to +125°C ±8
LOGIC INPUT/ OUTPUT
IIH High-level input current VEN = VAx = VDD 25°C –2 ± 0.6 2 µA
–55°C to +125°C –2 2
IIL Low-level input current VEN = VAx = 0V 25°C –1.1 ± 0.6 1.1 µA
–55°C to +125°C –1.2 1.2
SWITCHING CHARACTERISTICS
tON (EN) Enable turn-on time VS = 10V,
RL = 4kΩ, CL= 12pF		 25°C 165 265 ns
–40°C to +85°C 285
–55°C to +125°C 330
tOFF (EN) Enable turn-off time VS = 10V,
RL = 4kΩ, CL= 12pF		 25°C 350 400 ns
–40°C to +85°C 400
–55°C to +125°C 440
tTRAN Transition time VS = 10V,
RL = 4kΩ, CL= 12pF		 25°C 170 225 ns
–40°C to +85°C 245
–55°C to +125°C 285
tRESPONSE Fault response time VFP = 15V, VFN = –15V,
RL = 4kΩ, CL= 12pF		 25°C 300 ns
tRECOVERY Fault recovery time VFP = 15V, VFN = –15V,
RL = 4kΩ, CL= 12pF		 25°C 1.4 µs
tRESPONSE(FLAG) Fault flag response time VFP = 15V, VFN = –15V,
VPU = 5V, RPU = 1kΩ, CL= 12pF		 25°C 110 ns
tRECOVERY(FLAG) Fault flag recovery time VFP = 15V, VFN = –15V,
VPU = 5V, RPU = 1kΩ, CL= 12pF		 25°C 0.9 µs
tBBM Break-before-make time delay VS = 10V, RL = 4kΩ, CL= 12pF –55°C to +125°C 50 120 ns
QINJ Charge injection VS = 0 V, CL = 1nF 25°C –15 pC
OISO Off-isolation RS = 50Ω, RL = 50Ω, CL = 5pF,
VS = 200mVRMS, VBIAS = 0V, f = 1MHz		 25°C –82 dB
XTALK Intra-channel crosstalk RS = 50Ω, RL = 50Ω, CL = 5pF, VS = 200m VRMS, VBIAS = 0V, f = 1MHz 25°C –95 dB
BW –3dB bandwidth RS = 50Ω, RL = 50Ω, CL = 5pF,
VS = 200mVRMS, VBIAS = 0V		 25°C 150 MHz
ILOSS Insertion loss RS = 50Ω, RL = 50Ω, CL = 5pF,
VS = 200mVRMS, VBIAS = 0V, f = 1MHz		 25°C –9 dB
THD+N Total harmonic distortion plus noise RS = 40Ω, RL = 10kΩ, VS = 15 VPP, VBIAS = 0V, f = 20Hz to 20kHz 25°C 0.0014 %
CS(OFF) Input off-capacitance f = 1MHz, VS = 0V 25°C 3.5 pF
CD(OFF) Output off-capacitance f = 1MHz, VS = 0V 25°C 28 pF
CS(ON)
CD(ON)		 Input/Output on-capacitance f = 1MHz, VS = 0V 25°C 30 pF
POWER SUPPLY
IDD VDD supply current VDD = VFP = 16.5V, VSS = VFN =  –16.5V,
VAx = 0V, 5V, or VDD, VEN = 5V or VDD		 25°C 0.24 0.5 mA
–40°C to +85°C 0.5
–55°C to +125°C 0.5
ISS VSS supply current VDD = VFP = 16.5V, VSS = VFN =  –16.5V,
VAx = 0V, 5V, or VDD, VEN = 5V or VDD		 25°C 0.14 0.4 mA
–40°C to +85°C 0.4
–55°C to +125°C 0.4
IGND GND current VDD = VFP = 16.5V, VSS = VFN =  –16.5V,
VAx = 0V, 5V, or VDD, VEN = 5V or VDD		 25°C 0.075 mA
IFP VFP supply current VDD = VFP = 16.5V, VSS = VFN =  –16.5V,
VAx = 0V, 5V, or VDD, VEN = 5V or VDD		 25°C 10 µA
IFN VFN supply current VDD = VFP = 16.5V, VSS = VFN =  –16.5V,
VAx = 0V, 5V, or VDD, VEN = 5V or VDD		 25°C 10 µA
IDD(FA) VDD supply current under fault VS = ± 60V,
VDD = VFP = 16.5V, VSS = VFN =  –16.5V,
VAx = 0V, 5V, or VDD, VEN = 5V or VDD		 25°C 0.25 1 mA
–40°C to +85°C 1
–55°C to +125°C 1
ISS(FA) VSS supply current under fault VS = ± 60V,
VDD = VFP = 16.5V, VSS = VFN =  –16.5V,
VAx = 0V, 5V, or VDD, VEN = 5V or VDD		 25°C 0.15 0.5 mA
–40°C to +85°C 0.5
–55°C to +125°C 0.5
IGND(FA) GND current under fault VS = ± 60V,
VDD = VFP = 16.5V, VSS = VFN =  –16.5V,
VAx = 0V, 5V, or VDD, VEN = 5V or VDD		 25°C 0.15 mA
IFP(FA) VFP supply current under fault VS = ± 60V,
VDD = VFP = 16.5V, VSS = VFN =  –16.5V,
VAx = 0V, 5V, or VDD, VEN = 5V or VDD		 25°C 9 µA
IFN(FA) VFN supply current under fault VS = ± 60V,
VDD = VFP = 16.5V, VSS = VFN =  –16.5V,
VAx = 0V, 5V, or VDD, VEN = 5V or VDD		 25°C 9 µA
IDD(DISABLE) VDD supply current (disable mode) VDD = VFP = 16.5V, VSS = VFN =  –16.5V,
VAx = 0V, 5V, or VDD, VEN = 0V		 25°C 0.15 0.5 mA
–40°C to +85°C 0.5
–55°C to +125°C 0.5
ISS(DISABLE) VSS supply current (disable mode) VDD = VFP = 16.5V, VSS = VFN =  –16.5V,
VAx = 0V, 5V, or VDD, VEN = 0V		 25°C 0.1 0.4 mA
–40°C to +85°C 0.4
–55°C to +125°C 0.4
(1) When VS is positive,VD is negative. And when VS is negative, VD is positive.
(2) When VS is at a voltage potential, VD is floating. And when VD is at a voltage potential, VS is floating.