SLLSFY7 November   2025 ISOW6441 , ISOW6442

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Power Ratings
    6. 5.6  Insulation Specifications
    7. 5.7  Safety-Related Certifications
    8. 5.8  Safety Limiting Values
    9. 5.9  Electrical Characteristics - Power Converter
    10. 5.10 Supply Current Characteristics - Power Converter
    11. 5.11 Electrical Characteristics Channel Isolator - VDD = 5V, VDDL = 5V, VISO=5V
    12. 5.12 Supply Current Characteristics Channel Isolator - VDD, VDDL = 5V, VISO = 5V
    13. 5.13 Electrical Characteristics Channel Isolator - VDD = 5V, VDDL = 5V, VISO=3.3V
    14. 5.14 Supply Current Characteristics Channel Isolator - VDD, VDDL = 5V, VISO = 3.3V
    15. 5.15 Electrical Characteristics Channel Isolator - VDD = 3.3V, VDDL = 3.3V, VISO = 3.3V
    16. 5.16 Supply Current Characteristics Channel Isolator - VDD, VDDL = 3.3V, VISO = 3.3V
    17. 5.17 Electrical Characteristics Channel Isolator - VDDL = 2.5V
    18. 5.18 Supply Current Characteristics Channel Isolator - VDDL = 2.5V
    19. 5.19 Switching Characteristics - VDDL = 5V, VISO = 5V
    20. 5.20 Switching Characteristics - VDDL = 3.3V, VISO = 3.3V
    21. 5.21 Switching Characteristics - VDDL = 2.5V, VISO = 5V
    22. 5.22 Switching Characteristics - VDDL = 2.5V, VISO = 3.3V
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
      1. 7.1.1 Power Isolation
      2. 7.1.2 Signal Isolation
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Electromagnetic Compatibility (EMC) Considerations
      2. 7.3.2 Power-Up and Power-Down Behavior
      3. 7.3.3 Protection Features
    4. 7.4 Device Functional Modes
      1. 7.4.1 Device I/O Schematics
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
        1. 8.4.1.1 PCB Material
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Development Support
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 Receiving Notification of Documentation Updates
    4. 9.4 Support Resources
    5. 9.5 Trademarks
    6. 9.6 Electrostatic Discharge Caution
    7. 9.7 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information
    1.     PACKAGE OPTION ADDENDUM
    2. 11.1 Tape and Reel Information

6 Parameter Measurement Information

In the below images, VCCI and VCCO refers to the power supplies VDD and VISO, respectively.
ISOW6441 ISOW6442 Switching Characteristics Test Circuit and Voltage Waveforms
A. CL = 15pF and The input pulse is supplied by a generator having the following characteristics: PRR ≤ 50kHz, 50% duty cycle, tr ≤ 3ns, tf ≤ 3ns, ZO = 50Ω. At the input, 50Ω resistor is required to terminate Input Generator signal. The 50Ω resistor is not needed in actual application.
B. B. CL = 15pF and includes instrumentation and fixture capacitance within ±20%.
Figure 6-1 Switching Characteristics Test Circuit and Voltage Waveforms
ISOW6441 ISOW6442 Default Output Delay Time Test Circuit and Voltage Waveforms
Note: A. CL = 15pF and includes instrumentation and fixture capacitance within ±20%.
Note: B. Power Supply Ramp Rate = 10mV/ns.
Figure 6-2 Default Output Delay Time Test Circuit and Voltage Waveforms
ISOW6441 ISOW6442 Common-Mode Transient Immunity Test Circuit
Note: CL = 15pF and includes instrumentation and fixture capacitance within ±20%.
Note: Pass-fail criteria: Outputs must remain stable.
Figure 6-3 Common-Mode Transient Immunity Test Circuit