SLUS812E February   2008  – September 2025 TPS51200

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Sink and Source Regulator (VO Pin)
      2. 6.3.2  Reference Input (REFIN Pin)
      3. 6.3.3  Reference Output (REFOUT Pin)
      4. 6.3.4  Soft-Start Sequencing
      5. 6.3.5  Enable Control (EN Pin)
      6. 6.3.6  Powergood Function (PGOOD Pin)
      7. 6.3.7  Current Protection (VO Pin)
      8. 6.3.8  UVLO Protection (VIN Pin)
      9. 6.3.9  Thermal Shutdown
      10. 6.3.10 Tracking Start-up and Shutdown
      11. 6.3.11 Output Tolerance Consideration for VTT DIMM Applications
      12. 6.3.12 REFOUT (VREF) Consideration for DDR2 Applications
    4. 6.4 Device Functional Modes
      1. 6.4.1 Low Input Voltage Applications
      2. 6.4.2 S3 and Pseudo-S5 Support
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1 Input Voltage Capacitor
        2. 7.2.2.2 VLDO Input Capacitor
        3. 7.2.2.3 Output Capacitor
      3. 7.2.3 Application Curves
    3. 7.3 System Examples
      1. 7.3.1 3.3VIN, DDR2 Configuration
      2. 7.3.2 2.5VIN, DDR3 Configuration
      3. 7.3.3 3.3VIN, LP DDR3 or DDR4 Configuration
      4. 7.3.4 3.3VIN, DDR3 Tracking Configuration
      5. 7.3.5 3.3VIN, LDO Configuration
      6. 7.3.6 3.3VIN, DDR3 Configuration with LFP
    4. 7.4 Power Supply Recommendations
    5. 7.5 Layout
      1. 7.5.1 Layout Guidelines
      2. 7.5.2 Layout Example
      3. 7.5.3 Thermal Design Considerations
  9. 8 Device and Documentation Support
    1. 8.1 Device Support
      1. 8.1.1 Development Support
        1. 8.1.1.1 Evaluation Modules
        2. 8.1.1.2 Spice Models
    2. 8.2 Documentation Support
      1. 8.2.1 Related Documentation
    3. 8.3 Receiving Notification of Documentation Updates
    4. 8.4 Support Resources
    5. 8.5 Trademarks
    6. 8.6 Electrostatic Discharge Caution
    7. 8.7 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

4 Pin Configuration and Functions

TPS51200 TPS51200 DRC Package, 10-Pin VSON (Top View) Figure 4-1 TPS51200 DRC Package, 10-Pin VSON (Top View)
Table 4-1 Pin Functions
PIN I/O(2) DESCRIPTION
NAME NO.
EN 7 I For DDR VTT application, connect EN to SLP_S3. For any other application, use the EN pin as the ON/OFF function.
GND 8 G Signal ground.
PGND(1) 4 G Power ground for the LDO.
PGOOD 9 O Open-drain, power-good indicator.
REFIN 1 I Reference input.
REFOUT 6 O Reference output. Connect to GND through 0.1μF ceramic capacitor. If there is a REFOUT capacitors at DDR side, keep total capacitance on REFOUT pin below 0.47μF. The REFOUT pin can not be open.
VIN 10 I 2.5V or 3.3V power supply. A ceramic decoupling capacitor with a value between 1μF and 4.7μF is required.
VLDOIN 2 I Supply voltage for the LDO.
VO 3 O Power output for the LDO.
VOSNS 5 I Voltage sense input for the LDO. Connect to positive terminal of the output capacitor or the load.
(1) Thermal pad connection. See Figure 7-12 in the Section 7.5.3 section for additional information.
(2) I = Input, O = Output , G = Ground