SLVSDM4F
November 2018 – October 2026
TPS1HA08-Q1
PRODUCTION DATA
1
1
Features
2
Applications
3
Description
4
Device Comparison Table
5
Pin Configuration and Functions
5.1
Recommended Connections for Unused Pins
6
Specifications
6.1
Absolute Maximum Ratings
6.2
ESD Ratings
6.3
Recommended Operating Conditions
6.4
Thermal Information
6.5
Electrical Characteristics
6.6
Switching Characteristics
6.7
SNS Timing Characteristics
6.8
Typical Characteristics
7
Parameter Measurement Information
8
Detailed Description
8.1
Overview
8.1.1
Device Nomenclature
8.2
Functional Block Diagram
8.3
Feature Description
8.3.1
Protection Mechanisms
8.3.1.1
Thermal Shutdown
8.3.1.2
Current Limit
8.3.1.2.1
Current Limit Foldback
8.3.1.2.2
Selectable Current Limit Threshold
8.3.1.2.3
Undervoltage Lockout (UVLO)
8.3.1.2.4
VBB During Short-to-Ground
8.3.1.3
Energy Limit
8.3.1.4
Voltage Transients
8.3.1.4.1
Load Dump
8.3.1.4.2
Driving Inductive and Capacitive Loads
8.3.1.5
Reverse Battery
8.3.1.6
Fault Event – Timing Diagrams
8.3.2
Diagnostic Mechanisms
8.3.2.1
VOUT Short-to-Battery and Open-Load
8.3.2.1.1
Detection with Switch Enabled
8.3.2.1.2
Detection with Switch Disabled
8.3.2.2
SNS Output
8.3.2.2.1
RSNS Value
8.3.2.2.1.1
High Accuracy Load Current Sense
8.3.2.2.1.2
SNS Output Filter
8.3.2.3
ST Pin
8.3.2.4
Fault Indication and SNS Mux
8.3.2.5
Resistor Sharing
8.3.2.6
High-Frequency, Low Duty-Cycle Current Sensing
8.3.3
Enable Watchdog
8.4
Device Functional Modes
8.4.1
Off
8.4.2
Standby
8.4.3
Diagnostic
8.4.4
Standby Delay
8.4.5
Active
8.4.6
Fault
9
Application and Implementation
9.1
Application Information
9.1.1
Ground Protection Network
9.1.2
Interface with Microcontroller
9.1.3
I/O Protection
9.1.4
Inverse Current
9.1.5
Loss of GND
9.1.6
Automotive Standards
9.1.6.1
ISO7637-2
9.1.6.2
AEC – Q100-012 Short Circuit Reliability
9.1.7
Thermal Information
9.2
Typical Application
9.2.1
Design Requirements
9.2.2
Detailed Design Procedure
9.2.2.1
Thermal Considerations
9.2.2.2
Diagnostics
9.2.2.2.1
Selecting the RISNS Value
9.2.3
Application Curves
9.3
Power Supply Recommendations
9.4
Layout
9.4.1
Layout Guidelines
9.4.2
Layout Example
10
Device and Documentation Support
10.1
Device Support
10.1.1
Related Documentation
10.2
Receiving Notification of Documentation Updates
10.3
Support Resources
10.4
Trademarks
10.5
Electrostatic Discharge Caution
10.6
Glossary
11
Revision History
12
Mechanical, Packaging, and Orderable Information
1
Features
Single-channel smart high-side switch with 8mΩ R
ON
(T
J
= 25°C)
Qualified for automotive applications:
AEC Q-100 Qualified
Device temperature grade 1: –40°C to +125°C ambient operating temperature range
Withstands 40V load dump
Functional Safety-Capable
Documentation available to aid functional safety system design
Improve reliability through selectable current limiting
Current limit set-point at 20A or 80A
Overcurrent response of current clamping or instant shutdown
Robust integrated output protection:
Integrated thermal protection
Protection against short to ground and battery
Automatic switch-on during
reverse battery
Automatic shutoff if loss of battery and ground occurs
Integrated output clamp to demagnetize inductive loads
Configurable fault handling
Analog sense output is configurable to accurately measure
Load current
Supply voltage
Device temperature
Provides FLT indication back to MCU
Detection of open load and short-to-battery