SLVSIO7
July
2026
LM5192
PRODUCTION DATA
-
1
-
1 Features
-
2 Applications
-
3 Description
-
4 Related Products
-
5 Pin Configuration and Functions
-
6 Specifications
- 6.1
Absolute Maximum Ratings
- 6.2
ESD Ratings
- 6.3
Recommended Operating Conditions
- 6.4
Thermal Information
- 6.5
Electrical Characteristics
- 6.6
Timing Requirements for the Serial Control Bus
- 6.7
Typical Characteristics
-
7 Detailed Description
- 7.1
Overview
- 7.2
Functional Block Diagram
- 7.3
Feature Description
- 7.3.1
Input Voltage Range (VIN)
- 7.3.2
High-Voltage Bias Supply Regulators (VCC, VDDA)
- 7.3.3
Enable (EN)
- 7.3.4
Switching Frequency
- 7.3.5
Dual Random Spread Spectrum (DRSS)
- 7.3.6
Soft Start
- 7.3.7
Output Voltage
- 7.3.8
Minimum Controllable On-Time
- 7.3.9
Dual Loop Architecture
- 7.3.9.1
Voltage Loop Error Amplifier
- 7.3.9.2
Current Loop Error Amplifier
- 7.3.10
Programmable ILIM
- 7.3.11
IOUT Monitor
- 7.3.12
Cable Drop Compensation
- 7.3.13
Slope Compensation
- 7.3.14
Shunt Current Sensing
- 7.3.15
Hiccup Mode Current Limiting
- 7.3.16
Device Configuration (CNFG)
- 7.3.17
Pulse Frequency Modulation (PFM) / Synchronization
- 7.3.18
Out-of-Audio
Operation
- 7.3.19
Thermal Shutdown (TSD)
- 7.4
Device Functional Modes
- 7.4.1
Shutdown Mode
- 7.4.2
Standby Mode
- 7.4.3
Ready Mode
- 7.4.4
Active Mode
- 7.4.5
Sleep Mode
- 7.5
Programming
- 7.5.1
I2C Bus Operation
- 7.5.2
Clock Stretching
- 7.5.3
Data Transfer Formats
- 7.5.4
Single READ from a Defined Register
Address
- 7.5.5
Sequential READ Starting from a Defined
Register Address
- 7.5.6
Single WRITE to a Defined Register
Address
- 7.5.7
Sequential WRITE Starting at a Defined
Register Address
-
8 LM5192 Registers
-
9 Application and Implementation
- 9.1
Application Information
- 9.1.1
Power Train Components
- 9.1.1.1
Buck Inductor
- 9.1.1.2
Output Capacitors
- 9.1.1.3
Input Capacitors
- 9.1.1.4
EMI Filter
- 9.2
Typical Application
- 9.2.1
High Efficiency, Wide Input, 400kHz,
Synchronous Buck Regulator
- 9.2.1.1
Design Requirements
- 9.2.1.2
Detailed Design Procedure
- 9.2.1.2.1
Custom Design With WEBENCH® Tools
- 9.2.1.2.2
Buck Inductor
- 9.2.1.2.3
Current-Sense Resistance
- 9.2.1.2.4
Output Capacitors
- 9.2.1.2.5
Input Capacitors
- 9.2.1.2.6
Compensation Components
- 9.2.1.3
Application Curves
- 9.3
Power Supply Recommendations
- 9.4
Layout
- 9.4.1
Layout Guidelines
- 9.4.1.1
Thermal Design and Layout
- 9.4.2
Layout Example
-
10Device and Documentation Support
- 10.1
Device Support
- 10.1.1
Development Support
- 10.1.1.1
Custom Design With WEBENCH® Tools
- 10.2
Documentation Support
- 10.2.1
Related Documentation
- 10.2.1.1
PCB Layout Resources
- 10.2.1.2
Thermal Design Resources
- 10.3
Receiving Notification of Documentation Updates
- 10.4
Support Resources
- 10.5
Trademarks
- 10.6
Electrostatic Discharge Caution
- 10.7
Glossary
-
11Revision History
-
12Mechanical, Packaging, and Orderable Information
9.2.1.3 Application Curves
Figure 9-4 FPWM Mode
Efficiency, Linear Scale
Figure 9-6 Start-Up, EN
ON, VSUPPLY = 48V, ILOAD = 8A Resistive Load
Figure 9-8 Output Ripple,
VSUPPLY = 48V, ILOAD = 8A
Figure 9-10 Load Transient
Response, VSUPPLY = 48V, FPWM, 0A to 4A
Figure 9-12 CV to CC Mode
Transition, VSUPPLY = 48V, VLOAD = 12V to 9V
Figure 9-5 PFM Mode
Efficiency, Log Scale
Figure 9-7 Shutdown, EN
OFF, VSUPPLY = 48V, ILOAD = 8A Resistive Load
Figure 9-9 No Load
Operation in PFM Mode, VSUPPLY = 48V, ILOAD = 0A
Figure 9-11 Load Transient
Response, VSUPPLY = 48V, PFM, 0A to 4A
Figure 9-13 VSUPPLY = 48V, ILOAD = 8A, TA = 25°C, No
Airflow