SLVSJC6 December   2025 TPS544B27W

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Switching Characteristics
    8. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Operating Frequency and Mode
      2. 6.3.2 Setting the Output Voltage
      3. 6.3.3 DC Load Line
      4. 6.3.4 Fault Management
      5. 6.3.5 Current Sense and Positive Overcurrent Protection
      6. 6.3.6 Negative Overcurrent Limit
      7. 6.3.7 Zero-Crossing Detection
      8. 6.3.8 Overtemperature Protection
      9. 6.3.9 PMBus® Interface
        1. 6.3.9.1 Setting the PMBus® Address
        2. 6.3.9.2 SMBus Alert Response Address
    4. 6.4 Device Functional Modes
      1. 6.4.1 Forced Continuous-Conduction Mode
      2. 6.4.2 DCM Light Load Operation
    5. 6.5 Programming
      1. 6.5.1 PMBus® Command NVM Defaults
  8. 7 Register Maps
    1. 7.1 PMBus® Transaction Types
    2. 7.2 Conventions for Documenting Block Commands
    3. 7.3 PMBus Commands
      1. 7.3.1  OPERATION (Address = 01h)
      2. 7.3.2  ON_OFF_CONFIG (Address = 02h)
      3. 7.3.3  CLEAR_FAULTS (Address = 03h)
      4.      42
      5. 7.3.4  PASSKEY (Address = 0Eh)
      6. 7.3.5  WRITE_PROTECT (Address = 10h)
      7. 7.3.6  STORE_USER_ALL (Address = 15h)
      8.      46
      9. 7.3.7  RESTORE_USER_ALL (Address = 16h)
      10.      48
      11. 7.3.8  CAPABILITY (Address = 19h)
      12. 7.3.9  SMBALERT_MASK (Address = 1Bh)
      13.      51
      14. 7.3.10 SMBALERT_MASK Registers
        1. 7.3.10.1  ALERT_MASK_BYTE (Address = 78h) [Reset = C8h]
        2. 7.3.10.2  ALERT_MASK_WORD (Address = 79h) [Reset = 0Dh]
        3. 7.3.10.3  ALERT_MASK_VOUT (Address = 7Ah) [Reset = XXh]
        4. 7.3.10.4  ALERT_MASK_IOUT (Address = 7Bh) [Reset = XFh]
        5. 7.3.10.5  ALERT_MASK_INPUT (Address = 7Ch) [Reset = XXh]
        6. 7.3.10.6  ALERT_MASK_TEMPERATURE (Address = 7Dh) [Reset = XFh]
        7. 7.3.10.7  ALERT_MASK_CML (Address = 7Eh) [Reset = XXh]
        8. 7.3.10.8  ALERT_MASK_OTHER (Address = 7Fh) [Reset = XFh]
        9. 7.3.10.9  ALERT_MASK_MFR_SPECIFIC (Address = 80h) [Reset = XXh]
        10. 7.3.10.10 ALERT_MASK_PULSE_CATCHER (Address = CEh) [Reset = FXh]
      15. 7.3.11 VOUT_MODE (Address = 20h)
      16. 7.3.12 VOUT_COMMAND (Address = 21h)
      17. 7.3.13 VOUT_TRIM (Address = 22h)
      18. 7.3.14 VOUT_MAX (Address = 24h)
      19.      67
      20. 7.3.15 VOUT_MARGIN_HIGH (Address = 25h)
      21.      69
      22. 7.3.16 VOUT_MARGIN_LOW (Address = 26h)
      23.      71
      24. 7.3.17 VOUT_TRANSITION_RATE (Address = 27h)
      25.      73
      26. 7.3.18 VOUT_DROOP (Address = 28h)
      27. 7.3.19 VOUT_SCALE_LOOP (Address = 29h)
      28.      76
      29. 7.3.20 FREQUENCY_SWITCH (Address = 33h)
      30.      78
      31. 7.3.21 VIN_ON (Address = 35h)
      32.      80
      33. 7.3.22 VIN_OFF (Address = 36h)
      34.      82
      35. 7.3.23 VOUT_OV_FAULT_LIMIT (Address = 40h)
      36.      84
      37. 7.3.24 VOUT_OV_FAULT_RESPONSE (Address = 41h)
      38. 7.3.25 VOUT_OV_WARN_LIMIT (Address = 42h)
      39.      87
      40. 7.3.26 VOUT_UV_WARN_LIMIT (Address = 43h)
      41.      89
      42. 7.3.27 VOUT_UV_FAULT_LIMIT (Address = 44h)
      43.      91
      44. 7.3.28 VOUT_UV_FAULT_RESPONSE (Address = 45h)
      45. 7.3.29 IOUT_OC_FAULT_LIMIT (Address = 46h)
      46.      94
      47. 7.3.30 IOUT_OC_FAULT_RESPONSE (Address = 47h)
      48. 7.3.31 IOUT_OC_WARN_LIMIT (Address = 4Ah)
      49. 7.3.32 OT_FAULT_LIMIT (Address = 4Fh)
      50.      98
      51. 7.3.33 OT_FAULT_RESPONSE (Address = 50h)
      52. 7.3.34 OT_WARN_LIMIT (Address = 51h)
      53.      101
      54. 7.3.35 VIN_OV_FAULT_LIMIT (Address = 55h)
      55.      103
      56. 7.3.36 TON_DELAY (Address = 60h)
      57.      105
      58. 7.3.37 TON_RISE (Address = 61h)
      59. 7.3.38 TOFF_DELAY (Address = 64h)
      60. 7.3.39 TOFF_FALL (Address = 65h)
      61. 7.3.40 PIN_OP_WARN_LIMIT (Address = 6Bh)
      62.      110
      63.      111
      64.      112
      65. 7.3.41 STATUS_BYTE (Address = 78h)
      66. 7.3.42 STATUS_WORD (Address = 79h)
      67. 7.3.43 STATUS_VOUT (Address = 7Ah)
      68. 7.3.44 STATUS_IOUT (Address = 7Bh)
      69. 7.3.45 STATUS_INPUT (Address = 7Ch)
      70. 7.3.46 STATUS_TEMPERATURE (Address = 7Dh)
      71. 7.3.47 STATUS_CML (Address = 7Eh)
      72. 7.3.48 STATUS_OTHER (Address = 7Fh)
      73. 7.3.49 STATUS_MFR_SPECIFIC (Address = 80h)
      74. 7.3.50 READ_VIN (Address = 88h)
      75. 7.3.51 READ_IIN (Address = 89h)
      76. 7.3.52 READ_VOUT (Address = 8Bh)
      77. 7.3.53 READ_IOUT (Address = 8Ch)
      78. 7.3.54 READ_TEMPERATURE_1 (Address = 8Dh)
      79. 7.3.55 READ_PIN (Address = 97h)
      80. 7.3.56 PMBUS_REVISION (Address = 98h)
      81. 7.3.57 MFR_ID (Address = 99h)
      82. 7.3.58 MFR_MODEL (Address = 9Ah)
      83.      131
      84. 7.3.59 MFR_REVISION (Address = 9Bh)
      85. 7.3.60 IC_DEVICE_ID (Address = ADh)
      86. 7.3.61 IC_DEVICE_REV (Address = AEh)
      87.      135
      88. 7.3.62 EXTENDED_WRITE_PROTECT (Address = C7h)
      89. 7.3.63 NVM_PATCH_SPACE (Address = CDh)
      90. 7.3.64 CLOUD_OPTIONS (Address = CFh)
      91. 7.3.65 SYS_CFG_USER1 (Address = D0h)
      92.      140
      93. 7.3.66 SVID_ADDR_CFG_USER (Address = D1h)
      94. 7.3.67 PMBUS_ADDR (Address = D2h)
      95. 7.3.68 IMON_CAL (Address = D4h)
      96. 7.3.69 COMP (Address = D5h)
      97.      145
      98. 7.3.70 VBOOT_DCLL (Address = D6h)
      99. 7.3.71 VBOOT_OFFSET_1 (Address = D7h)
      100. 7.3.72 IIN_CAL (Address = D8h)
      101. 7.3.73 SVID_IMAX (Address = DAh)
      102.      150
      103. 7.3.74 SVID_EXT_CAPABILITY_VIDOMAX (Address = DBh)
      104. 7.3.75 FUSION_ID0 (Address = FCh)
      105. 7.3.76 FUSION_ID1 (Address = FDh)
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Application
      2. 8.2.2 Design Requirements
      3. 8.2.3 Detailed Design Procedure
        1. 8.2.3.1 Inductor Selection
        2. 8.2.3.2 Input Capacitor Selection
        3. 8.2.3.3 Output Capacitor Selection
        4. 8.2.3.4 VCC/VDRV Bypass Capacitor
        5. 8.2.3.5 BOOT Capacitor Selection
        6. 8.2.3.6 RSENSE Selection
        7. 8.2.3.7 I_IN_P and I_IN_M Capacitor Selection
        8. 8.2.3.8 VRRDY Pullup Resistor Selection
        9. 8.2.3.9 PMBus® Address Resistor Selection
      4. 8.2.4 Application Curves
        1. 8.2.4.1 Thermal Performance
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Receiving Notification of Documentation Updates
    2. 9.2 Support Resources
    3. 9.3 Trademarks
    4. 9.4 Electrostatic Discharge Caution
    5. 9.5 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

7.3.65 SYS_CFG_USER1 (Address = D0h)

SYS_CFG_USER1 is shown in Figure 7-71 and described in Table 7-91.

Return to the Summary Table.

Write Transaction: Write Word
Read Transaction: Read Word
Data Format: Unsigned binary (2 bytes)
NVM Back-up: EEPROM
Updates: On-the-fly. Some fields require the output to be disabled to take effect. This register contains miscellaneous bits for system configuration.

Figure 7-71 SYS_CFG_USER1
15141312111098
FCCMVOUT_CTRL[1:0]EN_SS_DCMPGD_DEL[1:0]SEL_NOC[1:0]
R/W-XhR/W-XhR/W-XhR/W-XhR/W-Xh
76543210
SEL_ALRT_FN[1:0]RESERVEDRESERVEDSEL_FIX_OVFEN_FIX_OVF
R/W-XhR/W-XR/W-XR/W-XhR/W-Xh
Table 7-91 SYS_CFG_USER1 Field Descriptions
BitFieldTypeResetDescription
15FCCMR/WX This bit selects between forced continuous mode conduction (FCCM) and discontinuous cooduction mode (DCM). PMBus writes are always accepted and the data is updated; however, in order for this bit to take effect, the output must be disabled.
  • 0h = DCM operation is enabled and automatically entered or exited based on zero-crossing detection of the low-side MOSFET sensed current.
  • 1h = FCCM.
14:13VOUT_CTRL[1:0]R/WX These bits determines how the output voltage of the rail is controlled. PMBus writes are always accepted and the data is updated; however, in order for this bit to take effect, the output must be disabled.
  • 0h = SVID control
  • 1h = SVID control and PMBus control
  • 2h = PMBus control
12EN_SS_DCMR/WX This bit forces DCM during soft start.
  • 0h = FCCM bit determines operation during soft start.
  • 1h = The device operates in DCM during soft start, overriding the setting in the FCCM bit during softstart.
11:10PGD_DEL[1:0]R/WX These bits set a delay time from soft start completion to the PGOOD/VRRDY pin going high. This delay time is included only once per startup of the rail.
  • 0h = 0.0015ms delay
  • 1h = 0.5ms delay
  • 2h = 1ms delay
  • 3h = 2ms delay
9:8SEL_NOC[1:0]R/WX These bits select the under current fault (UCF) threshold that limits the low-side MOSFET sinking current. The threshold depends on ICC_MAX as shown in the following table.
7:6SEL_ALRT_FN[1:0]R/WX These bits select the functionality of the ALERT pin.
  • 0h = SMB_ALERT#. All PMBus STATUS registers and their masking are used to determine assertion of the pin.
  • 1h = PINALERT#. When the power measured by the SVID PIN telemetry (SVID registers PIN_H and PIN_L) is greater than the SVID register PIN_ALERT_TH, the pin asserts low and holds low for 100 ms.
  • 2h = CAT_FAULT#. The pin asserts low if the device detects PS_FLT, OTF, UVF, or OVF statuses. Upon detection of UVF, this pin waits for a fixed delay time of 2 us and ignores the response delay programmed into TD_UV. Once a fault causes the CAT_FAULT# pin to assert low, the fault must be cleared for the pin to be released, such as through CLEAR_FAULTS or turning the output off and on through the ON_OFF_CONFIG mechanism.
  • 3h = VR_HOT#.
5:4RESERVEDR/WX
3:2RESERVEDR/WX
1SEL_FIX_OVFR/WX This bit is used to select the fixed output voltage OVF threshold. The threshold at the output also depends VOUT_SCALE_LOOP as shown in the following table.
  • 0h = Low threshold
  • 1h = High threshold
0EN_FIX_OVFR/WX This bit is used to enable the fixed output voltage OVF threshold.