SLVSJC6 December   2025 TPS544B27W

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Switching Characteristics
    8. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Operating Frequency and Mode
      2. 6.3.2 Setting the Output Voltage
      3. 6.3.3 DC Load Line
      4. 6.3.4 Fault Management
      5. 6.3.5 Current Sense and Positive Overcurrent Protection
      6. 6.3.6 Negative Overcurrent Limit
      7. 6.3.7 Zero-Crossing Detection
      8. 6.3.8 Overtemperature Protection
      9. 6.3.9 PMBus® Interface
        1. 6.3.9.1 Setting the PMBus® Address
        2. 6.3.9.2 SMBus Alert Response Address
    4. 6.4 Device Functional Modes
      1. 6.4.1 Forced Continuous-Conduction Mode
      2. 6.4.2 DCM Light Load Operation
    5. 6.5 Programming
      1. 6.5.1 PMBus® Command NVM Defaults
  8. 7 Register Maps
    1. 7.1 PMBus® Transaction Types
    2. 7.2 Conventions for Documenting Block Commands
    3. 7.3 PMBus Commands
      1. 7.3.1  OPERATION (Address = 01h)
      2. 7.3.2  ON_OFF_CONFIG (Address = 02h)
      3. 7.3.3  CLEAR_FAULTS (Address = 03h)
      4.      42
      5. 7.3.4  PASSKEY (Address = 0Eh)
      6. 7.3.5  WRITE_PROTECT (Address = 10h)
      7. 7.3.6  STORE_USER_ALL (Address = 15h)
      8.      46
      9. 7.3.7  RESTORE_USER_ALL (Address = 16h)
      10.      48
      11. 7.3.8  CAPABILITY (Address = 19h)
      12. 7.3.9  SMBALERT_MASK (Address = 1Bh)
      13.      51
      14. 7.3.10 SMBALERT_MASK Registers
        1. 7.3.10.1  ALERT_MASK_BYTE (Address = 78h) [Reset = C8h]
        2. 7.3.10.2  ALERT_MASK_WORD (Address = 79h) [Reset = 0Dh]
        3. 7.3.10.3  ALERT_MASK_VOUT (Address = 7Ah) [Reset = XXh]
        4. 7.3.10.4  ALERT_MASK_IOUT (Address = 7Bh) [Reset = XFh]
        5. 7.3.10.5  ALERT_MASK_INPUT (Address = 7Ch) [Reset = XXh]
        6. 7.3.10.6  ALERT_MASK_TEMPERATURE (Address = 7Dh) [Reset = XFh]
        7. 7.3.10.7  ALERT_MASK_CML (Address = 7Eh) [Reset = XXh]
        8. 7.3.10.8  ALERT_MASK_OTHER (Address = 7Fh) [Reset = XFh]
        9. 7.3.10.9  ALERT_MASK_MFR_SPECIFIC (Address = 80h) [Reset = XXh]
        10. 7.3.10.10 ALERT_MASK_PULSE_CATCHER (Address = CEh) [Reset = FXh]
      15. 7.3.11 VOUT_MODE (Address = 20h)
      16. 7.3.12 VOUT_COMMAND (Address = 21h)
      17. 7.3.13 VOUT_TRIM (Address = 22h)
      18. 7.3.14 VOUT_MAX (Address = 24h)
      19.      67
      20. 7.3.15 VOUT_MARGIN_HIGH (Address = 25h)
      21.      69
      22. 7.3.16 VOUT_MARGIN_LOW (Address = 26h)
      23.      71
      24. 7.3.17 VOUT_TRANSITION_RATE (Address = 27h)
      25.      73
      26. 7.3.18 VOUT_DROOP (Address = 28h)
      27. 7.3.19 VOUT_SCALE_LOOP (Address = 29h)
      28.      76
      29. 7.3.20 FREQUENCY_SWITCH (Address = 33h)
      30.      78
      31. 7.3.21 VIN_ON (Address = 35h)
      32.      80
      33. 7.3.22 VIN_OFF (Address = 36h)
      34.      82
      35. 7.3.23 VOUT_OV_FAULT_LIMIT (Address = 40h)
      36.      84
      37. 7.3.24 VOUT_OV_FAULT_RESPONSE (Address = 41h)
      38. 7.3.25 VOUT_OV_WARN_LIMIT (Address = 42h)
      39.      87
      40. 7.3.26 VOUT_UV_WARN_LIMIT (Address = 43h)
      41.      89
      42. 7.3.27 VOUT_UV_FAULT_LIMIT (Address = 44h)
      43.      91
      44. 7.3.28 VOUT_UV_FAULT_RESPONSE (Address = 45h)
      45. 7.3.29 IOUT_OC_FAULT_LIMIT (Address = 46h)
      46.      94
      47. 7.3.30 IOUT_OC_FAULT_RESPONSE (Address = 47h)
      48. 7.3.31 IOUT_OC_WARN_LIMIT (Address = 4Ah)
      49. 7.3.32 OT_FAULT_LIMIT (Address = 4Fh)
      50.      98
      51. 7.3.33 OT_FAULT_RESPONSE (Address = 50h)
      52. 7.3.34 OT_WARN_LIMIT (Address = 51h)
      53.      101
      54. 7.3.35 VIN_OV_FAULT_LIMIT (Address = 55h)
      55.      103
      56. 7.3.36 TON_DELAY (Address = 60h)
      57.      105
      58. 7.3.37 TON_RISE (Address = 61h)
      59. 7.3.38 TOFF_DELAY (Address = 64h)
      60. 7.3.39 TOFF_FALL (Address = 65h)
      61. 7.3.40 PIN_OP_WARN_LIMIT (Address = 6Bh)
      62.      110
      63.      111
      64.      112
      65. 7.3.41 STATUS_BYTE (Address = 78h)
      66. 7.3.42 STATUS_WORD (Address = 79h)
      67. 7.3.43 STATUS_VOUT (Address = 7Ah)
      68. 7.3.44 STATUS_IOUT (Address = 7Bh)
      69. 7.3.45 STATUS_INPUT (Address = 7Ch)
      70. 7.3.46 STATUS_TEMPERATURE (Address = 7Dh)
      71. 7.3.47 STATUS_CML (Address = 7Eh)
      72. 7.3.48 STATUS_OTHER (Address = 7Fh)
      73. 7.3.49 STATUS_MFR_SPECIFIC (Address = 80h)
      74. 7.3.50 READ_VIN (Address = 88h)
      75. 7.3.51 READ_IIN (Address = 89h)
      76. 7.3.52 READ_VOUT (Address = 8Bh)
      77. 7.3.53 READ_IOUT (Address = 8Ch)
      78. 7.3.54 READ_TEMPERATURE_1 (Address = 8Dh)
      79. 7.3.55 READ_PIN (Address = 97h)
      80. 7.3.56 PMBUS_REVISION (Address = 98h)
      81. 7.3.57 MFR_ID (Address = 99h)
      82. 7.3.58 MFR_MODEL (Address = 9Ah)
      83.      131
      84. 7.3.59 MFR_REVISION (Address = 9Bh)
      85. 7.3.60 IC_DEVICE_ID (Address = ADh)
      86. 7.3.61 IC_DEVICE_REV (Address = AEh)
      87.      135
      88. 7.3.62 EXTENDED_WRITE_PROTECT (Address = C7h)
      89. 7.3.63 NVM_PATCH_SPACE (Address = CDh)
      90. 7.3.64 CLOUD_OPTIONS (Address = CFh)
      91. 7.3.65 SYS_CFG_USER1 (Address = D0h)
      92.      140
      93. 7.3.66 SVID_ADDR_CFG_USER (Address = D1h)
      94. 7.3.67 PMBUS_ADDR (Address = D2h)
      95. 7.3.68 IMON_CAL (Address = D4h)
      96. 7.3.69 COMP (Address = D5h)
      97.      145
      98. 7.3.70 VBOOT_DCLL (Address = D6h)
      99. 7.3.71 VBOOT_OFFSET_1 (Address = D7h)
      100. 7.3.72 IIN_CAL (Address = D8h)
      101. 7.3.73 SVID_IMAX (Address = DAh)
      102.      150
      103. 7.3.74 SVID_EXT_CAPABILITY_VIDOMAX (Address = DBh)
      104. 7.3.75 FUSION_ID0 (Address = FCh)
      105. 7.3.76 FUSION_ID1 (Address = FDh)
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Application
      2. 8.2.2 Design Requirements
      3. 8.2.3 Detailed Design Procedure
        1. 8.2.3.1 Inductor Selection
        2. 8.2.3.2 Input Capacitor Selection
        3. 8.2.3.3 Output Capacitor Selection
        4. 8.2.3.4 VCC/VDRV Bypass Capacitor
        5. 8.2.3.5 BOOT Capacitor Selection
        6. 8.2.3.6 RSENSE Selection
        7. 8.2.3.7 I_IN_P and I_IN_M Capacitor Selection
        8. 8.2.3.8 VRRDY Pullup Resistor Selection
        9. 8.2.3.9 PMBus® Address Resistor Selection
      4. 8.2.4 Application Curves
        1. 8.2.4.1 Thermal Performance
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Receiving Notification of Documentation Updates
    2. 9.2 Support Resources
    3. 9.3 Trademarks
    4. 9.4 Electrostatic Discharge Caution
    5. 9.5 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

7.3.8 CAPABILITY (Address = 19h)

CAPABILITY is shown in Figure 7-6 and described in Table 7-7.

Return to the Summary Table.

Write Transaction: N/A
Read Transaction: Read Byte
Data Format: unsigned binary (1 byte)
NVM Back-up: No
Updates: N/A This command provides a way for the host to determine the capabilities of this PMBus device. This command is read-only and has one data byte formatted as below.

Figure 7-6 CAPABILITY
76543210
PECSPD[1:0]ALRTFORMATAVSRESERVEDRESERVED
R-1hR-2hR-1hR-0hR-0hR-0hR-0h
Table 7-7 CAPABILITY Field Descriptions
BitFieldTypeResetDescription
7PECR1h
  • 1h = Packet Error Checking is supported.
6:5SPD[1:0]R2h
  • 2h = Maximum supported bus speed is 1MHz.
4ALRTR1h
  • 1h = This device has an SMB_ALERT# pin and supports the SMBus Alert Response Protocol.
3FORMATR0h
  • 0h = Numeric format is LINEAR11, ULINEAR16, SLINEAR16, or DIRECT format.
2AVSR0h
  • 0h = AVSBus is NOT supported.
1RESERVEDR0h
0RESERVEDR0h