SLVSKW2 January   2026 ADS1278QML-SP

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Quality Conformance Inspection
    7. 5.7 Timing Requirements: SPI Format
    8. 5.8 Timing Requirements: Frame-Sync Format
    9. 5.9 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Sampling Aperture Matching
      2. 6.3.2  Frequency Response
        1. 6.3.2.1 High-Speed, Low-Power, And Low-Speed Modes
        2. 6.3.2.2 High-Resolution Mode
      3. 6.3.3  Phase Response
      4. 6.3.4  Settling Time
      5. 6.3.5  Data Format
      6. 6.3.6  Analog Inputs (AINP, AINN)
      7. 6.3.7  Voltage Reference Inputs (VREFP, VREFN)
      8. 6.3.8  Clock Input (CLK)
      9. 6.3.9  Mode Selection (MODE)
      10. 6.3.10 Synchronization (SYNC)
      11. 6.3.11 Power-Down ( PWDN)
      12. 6.3.12 Format[2:0]
      13. 6.3.13 Serial Interface Protocols
      14. 6.3.14 SPI Serial Interface
        1. 6.3.14.1 SCLK
        2. 6.3.14.2 DRDY/FSYNC (SPI Format)
        3. 6.3.14.3 DOUT
        4. 6.3.14.4 DIN
      15. 6.3.15 Frame-Sync Serial Interface
        1. 6.3.15.1 SCLK
        2. 6.3.15.2 DRDY/FSYNC (Frame-Sync Format)
        3. 6.3.15.3 DOUT
        4. 6.3.15.4 DIN
      16. 6.3.16 DOUT Modes
        1. 6.3.16.1 TDM Mode
        2. 6.3.16.2 TDM Mode, Fixed-Position Data
        3. 6.3.16.3 TDM Mode, Dynamic Position Data
        4. 6.3.16.4 Discrete Data Output Mode
      17. 6.3.17 Daisy-Chaining
      18. 6.3.18 Modulator Output
      19. 6.3.19 Pin Test Using Test[1:0] Inputs
      20. 6.3.20 VCOM Output
    4. 6.4 Device Functional Modes
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
      3. 7.2.3 Application Curve
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Receiving Notification of Documentation Updates
    2. 8.2 Community Resources
    3. 8.3 Trademarks
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

Pin Test Using Test[1:0] Inputs

The test mode feature of the ADS1278QML-SP allows continuity testing of the digital I/O pins. In this mode, the normal functions of the digital pins are disabled and routed to each other as pairs through internal logic, as shown in Table 6-14. The pins in the left column drive the output pins in the right column. Note: some of the digital input pins become outputs; these outputs must be accommodated in the design. The analog input, power supply, and ground pins all remain connected as normal. The test mode is engaged by setting the pins TEST [1:0] = 11. For normal converter operation, set TEST[1:0] = 00. Do not use '01' or '10'.

Table 6-14 Test Mode Pin Map (Test[1:0] = 11)
TEST MODE PIN MAP
INPUT PINSOUTPUT PINS
PWDN1DOUT1
PWDN2DOUT2
PWDN3DOUT3
PWDN4DOUT4
PWDN5DOUT5
PWDN6DOUT6
PWDN7DOUT7
PWDN8DOUT8
MODE0DIN
MODE1SYNC
FORMAT0CLKDIV
FORMAT1FSYNC/ DRDY
FORMAT2SCLK