SLVSKW2 January   2026 ADS1278QML-SP

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Quality Conformance Inspection
    7. 5.7 Timing Requirements: SPI Format
    8. 5.8 Timing Requirements: Frame-Sync Format
    9. 5.9 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Sampling Aperture Matching
      2. 6.3.2  Frequency Response
        1. 6.3.2.1 High-Speed, Low-Power, And Low-Speed Modes
        2. 6.3.2.2 High-Resolution Mode
      3. 6.3.3  Phase Response
      4. 6.3.4  Settling Time
      5. 6.3.5  Data Format
      6. 6.3.6  Analog Inputs (AINP, AINN)
      7. 6.3.7  Voltage Reference Inputs (VREFP, VREFN)
      8. 6.3.8  Clock Input (CLK)
      9. 6.3.9  Mode Selection (MODE)
      10. 6.3.10 Synchronization (SYNC)
      11. 6.3.11 Power-Down ( PWDN)
      12. 6.3.12 Format[2:0]
      13. 6.3.13 Serial Interface Protocols
      14. 6.3.14 SPI Serial Interface
        1. 6.3.14.1 SCLK
        2. 6.3.14.2 DRDY/FSYNC (SPI Format)
        3. 6.3.14.3 DOUT
        4. 6.3.14.4 DIN
      15. 6.3.15 Frame-Sync Serial Interface
        1. 6.3.15.1 SCLK
        2. 6.3.15.2 DRDY/FSYNC (Frame-Sync Format)
        3. 6.3.15.3 DOUT
        4. 6.3.15.4 DIN
      16. 6.3.16 DOUT Modes
        1. 6.3.16.1 TDM Mode
        2. 6.3.16.2 TDM Mode, Fixed-Position Data
        3. 6.3.16.3 TDM Mode, Dynamic Position Data
        4. 6.3.16.4 Discrete Data Output Mode
      17. 6.3.17 Daisy-Chaining
      18. 6.3.18 Modulator Output
      19. 6.3.19 Pin Test Using Test[1:0] Inputs
      20. 6.3.20 VCOM Output
    4. 6.4 Device Functional Modes
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
      3. 7.2.3 Application Curve
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Receiving Notification of Documentation Updates
    2. 8.2 Community Resources
    3. 8.3 Trademarks
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

High-Speed, Low-Power, And Low-Speed Modes

The digital filter configuration is the same in High-Speed, Low-Power, and Low-Speed modes with the oversampling ratio set to 64. Figure 6-1 shows the frequency response in High-Speed, Low-Power, and Low-Speed modes normalized to fDATA. Figure 6-2 shows the passband ripple. The transition from passband to stop band is shown in Figure 6-3. The overall frequency response repeats at 64x multiples of the modulator frequency fMOD, as shown in Figure 6-4.

ADS1278QML-SP Frequency Response For High-Speed, Low-Power, And Low-Speed ModesFigure 6-1 Frequency Response For High-Speed, Low-Power, And Low-Speed Modes
ADS1278QML-SP Passband Response For High-Speed, Low-Power, And Low-Speed ModesFigure 6-2 Passband Response For High-Speed, Low-Power, And Low-Speed Modes
ADS1278QML-SP Transition Band Response For High-Speed, Low-Power, and Low-Speed ModesFigure 6-3 Transition Band Response For High-Speed, Low-Power, and Low-Speed Modes
ADS1278QML-SP Frequency Response Out To FMOD For High-Speed, Low-Power, And Low-Speed ModesFigure 6-4 Frequency Response Out To FMOD For High-Speed, Low-Power, And Low-Speed Modes

These image frequencies, if present in the signal and not externally filtered, folds back (or alias) into the passband, causing errors. The stop band of the ADS1278QML-SP provides 100dB attenuation of frequencies that begin just beyond the passband and continue out to fMOD. Placing an anti-aliasing, low-pass filter in front of the ADS1278QML-SP inputs is recommended to limit possible high-amplitude, out-of-band signals and noise. Often, a simple RC filter is sufficient. Table 6-2 lists the image rejection versus external filter order.

Table 6-2 Antialiasing Filter Order Image Rejection
ANTIALIASING FILTER ORDERIMAGE REJECTION (dB)
(f–3dB at fDATA)
HS, LP, LSHR
13945
27587
3111129