SLVUCU5 December   2025 UCD91160 , UCD91320

 

  1.   1
  2.   Abstract
  3.   Trademarks
  4. 1 Power Supply Sequencing
    1. 1.1 Overview
    2. 1.2 Rail On and Off Configuration
    3. 1.3 Rail Power Good
    4. 1.4 Rail Sequence Configuration
    5. 1.5 Rail States
    6. 1.6 Rail Sequencing Example Use Cases
  5. 2 GPIOs
    1. 2.1 Overview
    2. 2.2 Command Controlled GPOs
    3. 2.3 Logic GPOs
      1. 2.3.1 Boolean Logic Builder
    4. 2.4 GPIs
      1. 2.4.1 GPI Special Functionality
      2. 2.4.2 GPI Fault Responses
      3. 2.4.3 GPI Latched Status Clearing
      4. 2.4.4 GPI Debug Pin
      5. 2.4.5 GPI Fault Pin
    5. 2.5 Power Supply Enable Pins
    6. 2.6 Cascading Pins
    7. 2.7 Margining Pins
  6. 3 GPI State Machine
    1. 3.1 Overview
    2. 3.2 GPI State Machine Configuration
  7. 4 Monitoring
  8. 5 Rail Profiles
  9. 6 Margining
    1. 6.1 Overview
    2. 6.2 Operation
    3. 6.3 Idle Behavior of Margining Pins
  10. 7 Cascading
    1. 7.1 Overview
    2. 7.2 Power On Cascading
    3. 7.3 Power On and Off Cascading
    4. 7.4 Fault Cascading
    5. 7.5 Cascading Requirements
  11. 8 Fault Handling
  12. 9 Fault Logging
  13. 10Memory
    1. 10.1 Overview
    2. 10.2 Flash Memory
    3. 10.3 Power Up
    4. 10.4 Program Lifetime
  14. 11Internal Fault Management
  15. 12Status Monitoring
  16. 13Device Reset
  17. 14ADC Reference
  18. 15System Watchdog
  19. 16System Reset
  20. 17PMBus Specification
    1. 17.1 Manufacturer Specific Status (STATUS_MFR_SPECIFIC)
  21. 18Data Formats
    1. 18.1 Data Format for Output Voltage Parameters
    2. 18.2 Data Format for Other Parameters
    3. 18.3 Distinguishing Between Linear Data Formats
    4. 18.4 Translation, Quantization, and Truncation
    5. 18.5 8-Bit Time Encoding
    6. 18.6 16-Bit Time Encoding
  22. 19Memory Model
  23. 20Alert Response Address Support
  24. 21Supported PMBus Commands
  25. 22Implementation Details for PMBus Core Commands
    1. 22.1  (00h) PAGE
    2. 22.2  (01h) OPERATION
    3. 22.3  (0Eh) PASSKEY
    4. 22.4  (0Fh) ACCESS_CONTROL
    5. 22.5  (11h) STORE_DEFAULT_ALL
    6. 22.6  (12h) RESTORE_DEFAULT_ALL
    7. 22.7  (1Bh) SMBALERT_MASK
    8. 22.8  (20h) VOUT_MODE
    9. 22.9  (38h) IOUT_CAL_GAIN
    10. 22.10 (41h – 69h) xxx_FAULT_RESPONSE
    11. 22.11 (62h) TON_MAX_FAULT_LIMIT
    12. 22.12 (66h) TOFF_MAX_WARN_LIMIT
    13. 22.13 (80h) STATUS_MFR_SPECIFIC
    14. 22.14 (8Dh) READ_TEMPERATURE_1
    15. 22.15 (8Eh) READ_TEMPERATURE_2
    16. 22.16 (ADh) IC_DEVICE_ID
    17. 22.17 (AEh) IC_DEVICE_REV
  26. 23Input and Output Pin Configuration
  27. 24PWM Configuration
  28. 25Implementation Details for User Data Commands
    1. 25.1 (B5h) FIRST_BLACK_BOX_FAULT_INFO (USER_DATA_05)
    2. 25.2 (B6h) LAST_BLACK_BOX_FAULT_INFO Command Format(USER_DATA_06)
    3. 25.3 (B8h) RAIL_PROFILE (USER_DATA_08)
      1. 25.3.1 Number Profile
      2. 25.3.2 Profile Index
    4. 25.4 (B9h) RAIL_STATE (USER_DATA_09)
  29. 26Implementation Details for Manufacturer-Specific Commands
    1. 26.1  Manufacturer-Specific Commands Notice
    2. 26.2  (D0h) FAULT_PIN_CONFIG (MFR_SPECIFIC_00)
      1. 26.2.1 Fault Pin Configuration
      2. 26.2.2 Page Mask
      3. 26.2.3 GPI Mask
      4. 26.2.4 Other Mask
    3. 26.3  (D1h) VOUT_CAL_MONITOR (MFR_SPECIFIC_01)
    4. 26.4  (D2h) SYSTEM_RESET_CONFIG (MFR_SPECIFIC_02)
      1. 26.4.1 GPI Flags
      2. 26.4.2 Page Flags
      3. 26.4.3 Deassert When Power-Good
      4. 26.4.4 Assert When NOT Power-Good
      5. 26.4.5 Assert When Watchdog Timeout
      6. 26.4.6 Delay Time
      7. 26.4.7 Pulse Time
      8. 26.4.8 GPI Tracking
      9. 26.4.9 Reset Pin Configuration
    5. 26.5  (D3h) SYSTEM_WATCHDOG_CONFIG (MFR_SPECIFIC_03)
      1. 26.5.1 Enable
      2. 26.5.2 Watch Reset Pin
      3. 26.5.3 Disable Until System Reset Release
      4. 26.5.4 Start Time
      5. 26.5.5 Input Pin (WDI) Configuration
      6. 26.5.6 Reset Period
      7. 26.5.7 Output Pin (WDO) Configuration
    6. 26.6  (D4h) SYSTEM_WATCHDOG_RESET (MFR_SPECIFIC_04)
    7. 26.7  (D5h) MONITOR_CONFIG (MFR_SPECIFIC_05)
    8. 26.8  (D6h) NUM_PAGES (MFR_SPECIFIC_06)
    9. 26.9  (D7h) RUN_TIME_CLOCK (MFR_SPECIFIC_07)
    10. 26.10 (D8h) RUN_TIME_CLOCK_TRIM (MFR_SPECIFIC_08)
    11. 26.11 (DAh) USER_RAM_00 (MFR_SPECIFIC_10)
    12. 26.12 (DBh) SOFT_RESET (MFR_SPECIFIC_11)
    13. 26.13 (DCh) RESET_COUNT (MFR_SPECIFIC_12)
    14. 26.14 (DDh) PIN_SELECTED_RAIL_STATES (MFR_SPECIFIC_13)
      1. 26.14.1 System State Enables
      2. 26.14.2 Soft Off Enables
      3. 26.14.3 System State
    15. 26.15 (DEh) RESEQUENCE (MFR_SPECIFIC_14)
    16. 26.16 (DFh) CONSTANTS (MFR_SPECIFIC_15)
    17. 26.17 (E0h) PWM_SELECT (MFR_SPECIFIC_16)
    18. 26.18 (E1h) PWM_CONFIG (MFR_SPECIFIC_17)
    19. 26.19 (E2h) PARM_INFO (MFR_SPECIFIC_18)
    20. 26.20 (E3h) PARM_VALUE (MFR_SPECIFIC_19)
    21. 26.21 (E4h) TEMPERATURE_CAL_GAIN (MFR_SPECIFIC_20)
    22. 26.22 (E5h) TEMPERATURE_CAL_OFFSET (MFR_SPECIFIC_21)
    23. 26.23 (E6h) SET_BREAKPOINTS (MFR_SPECIFIC 22)
    24. 26.24 (E7h) DEBUG_CONTINUE (MFR_SPECIFIC_23)
    25. 26.25 (E9h) FAULT_RESPONSES (MFR_SPECIFIC_25)
      1. 26.25.1 Fault Response Bytes
      2. 26.25.2 Re-Sequence
      3. 26.25.3 Time Between Retries
      4. 26.25.4 Maximum Glitch Time for Voltage Faults
      5. 26.25.5 Maximum Glitch Time for Non-Voltage Faults
    26. 26.26 (EAh) LOGGED_FAULTS (MFR_SPECIFIC_26)
      1. 26.26.1 Command Format
      2. 26.26.2 Non-Paged Faults
      3. 26.26.3 GPI Faults
      4. 26.26.4 Page-Dependent Faults
    27. 26.27 (EBh) LOGGED_FAULT_DETAIL_INDEX (MFR_SPECIFIC_27)
    28. 26.28 (ECh) LOGGED_FAULT_DETAIL (MFR_SPECIFIC_28)
    29. 26.29 (EFh) LOG_FAULT_DETAIL_ENABLES (MFR_SPECIFIC_31)
    30. 26.30 (F0h) EXECUTE_FLASH (MFR_SPECIFIC_32)
    31. 26.31 (F1h) SECURITY (MFR_SPECIFIC_33)
    32. 26.32 F2h) SECURITY_BIT_MASK (MFR_SPECIFIC_34)
    33. 26.33 (F3h) MFR_STATUS (MFR_SPECIFIC_35)
    34. 26.34 (F4h) GPI_FAULT_RESPONSES (MFR_SPECIFIC_36)
      1. 26.34.1 Fault Responses Byte
      2. 26.34.2 Time Between Retries
      3. 26.34.3 Maximum Glitch Time for GPI
      4. 26.34.4 GPI Number Rail Profile Pin Selection
      5. 26.34.5 Block Out Period for Profile
    35. 26.35 (F5h) MARGIN_CONFIG (MFR_SPECIFIC_37)
    36. 26.36 (F6h) SEQ_CONFIG (MFR_SPECIFIC_38)
      1. 26.36.1  Enable Pin Configuration
      2. 26.36.2  GPI Sequence On Dependency Mask
      3. 26.36.3  GPI Sequence Off Dependency Mask
      4. 26.36.4  Sequencing Timeout Configuration
      5. 26.36.5  Sequencing On Timeout
      6. 26.36.6  Sequencing Off Timeout
      7. 26.36.7  Page Sequence On Dependency Mask
      8. 26.36.8  Page Sequence Off Dependency Mask
      9. 26.36.9  Fault Slaves Mask
      10. 26.36.10 GPO Sequence On Dependency Mask
      11. 26.36.11 GPO Sequence Off Dependency Mask
    37. 26.37 (F7h) GPO_CONFIG_INDEX (MFR_SPECIFIC_39)
    38. 26.38 (F8h) GPO_CONFIG (MFR_SPECIFIC_40)
      1. 26.38.1  Output Pin Configuration
      2. 26.38.2  Assert Delay Enable
      3. 26.38.3  Deassert Delay Enable
      4. 26.38.4  Invert OR Output
      5. 26.38.5  Ignore Inputs During Delay
      6. 26.38.6  Invert AND Output
      7. 26.38.7  State Machine Mode Enable
      8. 26.38.8  High Resolution Delay Count
      9. 26.38.9  Millisecond Delay
      10. 26.38.10 Status Mask
      11. 26.38.11 Status Inversion Mask
      12. 26.38.12 GPI Mask
      13. 26.38.13 GPI Inversion Mask
      14. 26.38.14 GPO Mask
      15. 26.38.15 GPO Inversion Mask
      16. 26.38.16 Status Type Select
      17. 26.38.17 GPO Configuration Examples
    39. 26.39 (F9h) GPI_CONFIG (MFR_SPECIFIC_41)
      1. 26.39.1 GPI Pin Configuration
      2. 26.39.2 Fault Enable Flags
      3. 26.39.3 Latched Statuses Clear Pin Selection
      4. 26.39.4 MRG_EN Pin Selection
      5. 26.39.5 MRG_LOW_nHIGH Pin Selection
      6. 26.39.6 Maximum Glitch Time for Fault Pin
      7. 26.39.7 GPI Debug Mode Pin Selection
    40. 26.40 (FAh) GPIO_SELECT (MFR_SPECIFIC_42)
    41. 26.41 (FBh) GPIO_CONFIG (MFR_SPECIFIC_43)
    42. 26.42 (FCh) MISC_CONFIG (MFR_SPECIFIC_44)
      1. 26.42.1 Miscellaneous Configuration Byte
      2. 26.42.2 Time Between Resequences
      3. 26.42.3 External Reference Voltage
      4. 26.42.4 Resequence_rails_mask
    43. 26.43 (FDh) DEVICE_ID (MFR_SPECIFIC_45)
  30. 27Range Checking and Limits
  31. 28Glossary
  32. 29Revision History

(F6h) SEQ_CONFIG (MFR_SPECIFIC_38)

This Read/Write Block command configures the sequencing dependencies and enable pin for a given rail.

Features include:

  1. Sequencing – Configures interdependency between how voltage rails are enabled/disabled
  2. Fault Slaves – Configure slave pages which also shut down when a fault occurs
  3. Enable Pin – Identifies the enable pin, and its operating characteristics.
Note:

All configurations done with the GPI_CONFIG command must be done before writing this command.

When this command is written, the enable pin for the rail is deasserted. Then the state of the rail is re-evaluated. If it is determined that the rail should be on, the enable pin is then asserted.

Table 26-38 SEQ_CONFIG Command Format
Byte Number
(Write)
Byte Number
(Read)
Payload
Index
Description
0CMD = F6
10BYTE_COUNT =

29

210Enable Pin Configuration

(Pin ID)

3

2

1

Enable Pin Configuration (Other)

4

3

2

GPI Sequence On Dependency Mask (Byte 0 - LSB)

5

4

3

GPI Sequence On Dependency Mask (Byte 1)

6

5

4

GPI Sequence On Dependency Mask (Byte 2)

7

6

5

GPI Sequence On Dependency Mask (Byte 3 - MSB)

8

7

6

GPI Sequence Off Dependency Mask (Byte 0 - LSB)

9

8

7

GPI Sequence Off Dependency Mask (Byte 1)

10

9

8

GPI Sequence Off Dependency Mask (Byte 2)

11

10

9

GPI Sequence Off Dependency Mask (Byte 3- LSB)

12

11

10

Sequencing Timeout Configuration
13

12

11

Sequencing On Timeout
1413

12

Sequencing Off Timeout
151

4

1

3

Page Sequence On Dependency Mask (Byte 0 - LSB)
161

5

1

4

Page Sequence On Dependency Mask (Byte 1)
171

6

1

5

Page Sequence On Dependency Mask (Byte 2)

18

17

16

Page Sequence On Dependency Mask (Byte 3- MSB)
191

8

17

Page Sequence Off Dependency Mask (Byte 0 - LSB)

20

1

9

18

Page Sequence Off Dependency Mask (Byte 1)

21

20

19

Page Sequence Off Dependency Mask (Byte 2)

22

21

20

Page Sequence Off Dependency Mask (Byte 3- MSB)

23

22

21

Fault Slaves Mask (Byte 0 - LSB)

24

23

22

Fault Slaves Mask (Byte 1)

25

24

23

Fault Slaves Mask (Byte 2)

26

25

24

Fault Slaves Mask (Byte 3- LSB)

27

26

25

GPO Sequence On Dependency Mask (Byte 0)

28

27

26

GPO Sequence On Dependency Mask (Byte 1)

29

28

27

GPO Sequence Off Dependency Mask

(Byte 0)

30

29

28

GPO Sequence Off Dependency Mask (Byte 1)

The turn on condition for each page can depend on the state of several other pages or input pins. The same pages and pins also may be used to control multiple pages. The GPI and Page dependencies (Sequence On Dependencies) define a set of conditions which allow a page to turn on when met. Note that the logical AND of all conditions must be met before a page can be turned on. Once the page is on, these dependencies have no further effect on the operating status of the page. Specifically, they do not cause a page to turn off.

Sequence On Dependencies work in parallel with the PMBus defined mechanisms used to enable an output. That is, both the Sequence On Dependencies and the PMBus mechanism must be satisfied. For example, if the page responds to an OPERATION command and the OPERATION command specifies OFF, the page remains off even if all of the sequencing Sequence On Dependencies are met. Further, the order in which they are met is irrelevant; if the OPERATION command is issued first, the page waits for the sequencing requirements to be met before it can be turned on; or if the sequencing requirements are met first, the page waits for the OPERATION command before it can be turned on.

In the ON_OFF_CONFIG command, a “None” setting is still subject to the specified Sequence On Dependencies.

Turn on delay (TON_DELAY) is applied after the page has been commanded on and all Sequence On Dependencies are met.

Unless the rail is instructed to turn off immediately, the previous descriptions also apply to the Sequence Off Dependencies – they must be met before the rail is turned off, the turn off delay (TOFF_DELAY) is applied after the dependencies are met, and so forth.

After a fault, the PMBus specification requires that an OFF/ON sequence occurs before the rail is allowed to restart. The toggle of sequencing pin (such as CONTROL pin and Pin-Selected State GPI) is interpreted to meet this requirement. For example, consider a page that responds to the CONTROL pin and was shut down due to a fault. A toggle low then high on the CONTROL pin is sufficient to restart the page.