SNAS786C July   2020  – July 2025 CDCE6214-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  EEPROM Characteristics
    6. 5.6  Reference Input, Single-Ended Characteristics
    7. 5.7  Reference Input, Differential Characteristics
    8. 5.8  Reference Input, Crystal Mode Characteristics
    9. 5.9  General-Purpose Input Characteristics
    10. 5.10 Triple Level Input Characteristics
    11. 5.11 Logic Output Characteristics
    12. 5.12 Phase Locked Loop Characteristics
    13. 5.13 Closed-Loop Output Jitter Characteristics
    14. 5.14 Input and Output Isolation
    15. 5.15 Buffer Mode Characteristics
    16. 5.16 PCIe Spread Spectrum Generator
    17. 5.17 LVCMOS Output Characteristics
    18. 5.18 LP-HCSL Output Characteristics
    19. 5.19 LVDS Output Characteristics
    20. 5.20 Output Synchronization Characteristics
    21. 5.21 Power-On Reset Characteristics
    22. 5.22 I2C-Compatible Serial Interface Characteristics
    23. 5.23 Timing Requirements, I2C-Compatible Serial Interface
    24. 5.24 Power Supply Characteristics
    25. 5.25 Typical Characteristics
  7. 6 Parameter Measurement Information
    1. 6.1 Reference Inputs
    2. 6.2 Outputs
    3. 6.3 Serial Interface
    4. 6.4 PSNR Test
    5. 6.5 Clock Interfacing and Termination
      1. 6.5.1 Reference Input
      2. 6.5.2 Outputs
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Reference Block
        1. 7.3.1.1 Zero Delay Mode, Internal and External Path
      2. 7.3.2 Phase-Locked Loop (PLL)
        1. 7.3.2.1 PLL Configuration and Divider Settings
        2. 7.3.2.2 Spread Spectrum Clocking
        3. 7.3.2.3 Digitally-Controlled Oscillator and Frequency Increment or Decrement - Serial Interface Mode and GPIO Mode
      3. 7.3.3 Clock Distribution
        1. 7.3.3.1 Glitchless Operation
        2. 7.3.3.2 Divider Synchronization
        3. 7.3.3.3 Global and Individual Output Enable
      4. 7.3.4 Power Supplies and Power Management
      5. 7.3.5 Control Pins
    4. 7.4 Device Functional Modes
      1. 7.4.1 Operation Modes
        1. 7.4.1.1 Fall-Back Mode
        2. 7.4.1.2 Pin Mode
        3. 7.4.1.3 Serial Interface Mode
    5. 7.5 Programming
      1. 7.5.1 I2C Serial Interface
      2. 7.5.2 EEPROM
        1. 7.5.2.1 EEPROM - Cyclic Redundancy Check
        2. 7.5.2.2 Recommended Programming Procedure
        3. 7.5.2.3 EEPROM Access
          1. 7.5.2.3.1 Register Commit Flow
          2. 7.5.2.3.2 Direct Access Flow
        4. 7.5.2.4 Register Bits to EEPROM Mapping
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
      1. 8.3.1 Power-Up Sequence
      2. 8.3.2 Decoupling
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Examples
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Development Support
      2. 9.1.2 Device Nomenclature
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 Receiving Notification of Documentation Updates
    4. 9.4 Support Resources
    5. 9.5 Trademarks
    6. 9.6 Electrostatic Discharge Caution
    7. 9.7 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information
    1. 11.1 Package Option Addendum
    2. 11.2 Tape and Reel Information

8.1 Application Information

A typical application using the I2C interface and a 25-MHz crystal input is shown in Figure 8-1. The two ends of 25-MHz XTAL are connected to pin 1 and 2. The REFSEL pin is pulled down to select a secondary input. The HW_SW_CTRL can be pulled either low or high if EEPROM is used, or kept floating if EEPROM is unused. 1.8 V, 2.5 V, or 3.3 V can be supplied to the VDD_REF and VDD_VCO pins, as well as VDDO_12 and VDDO_34 pins with filtering. Data and clock lines of I2C must be pulled to VDD_REF using pullup resistors. The PDN can be connected to the MCU if a hardware reset is required, otherwise the PDN can be left floating. The GPIO1 and 4 pins can be connected to the MCU if needed, otherwise these pins can be left floating. Unused outputs can be left floating.

CDCE6214-Q1 Typical Application Schematic With I2C InterfaceFigure 8-1 Typical Application Schematic With I2C Interface