SNAS786C July   2020  – July 2025 CDCE6214-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  EEPROM Characteristics
    6. 5.6  Reference Input, Single-Ended Characteristics
    7. 5.7  Reference Input, Differential Characteristics
    8. 5.8  Reference Input, Crystal Mode Characteristics
    9. 5.9  General-Purpose Input Characteristics
    10. 5.10 Triple Level Input Characteristics
    11. 5.11 Logic Output Characteristics
    12. 5.12 Phase Locked Loop Characteristics
    13. 5.13 Closed-Loop Output Jitter Characteristics
    14. 5.14 Input and Output Isolation
    15. 5.15 Buffer Mode Characteristics
    16. 5.16 PCIe Spread Spectrum Generator
    17. 5.17 LVCMOS Output Characteristics
    18. 5.18 LP-HCSL Output Characteristics
    19. 5.19 LVDS Output Characteristics
    20. 5.20 Output Synchronization Characteristics
    21. 5.21 Power-On Reset Characteristics
    22. 5.22 I2C-Compatible Serial Interface Characteristics
    23. 5.23 Timing Requirements, I2C-Compatible Serial Interface
    24. 5.24 Power Supply Characteristics
    25. 5.25 Typical Characteristics
  7. 6 Parameter Measurement Information
    1. 6.1 Reference Inputs
    2. 6.2 Outputs
    3. 6.3 Serial Interface
    4. 6.4 PSNR Test
    5. 6.5 Clock Interfacing and Termination
      1. 6.5.1 Reference Input
      2. 6.5.2 Outputs
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Reference Block
        1. 7.3.1.1 Zero Delay Mode, Internal and External Path
      2. 7.3.2 Phase-Locked Loop (PLL)
        1. 7.3.2.1 PLL Configuration and Divider Settings
        2. 7.3.2.2 Spread Spectrum Clocking
        3. 7.3.2.3 Digitally-Controlled Oscillator and Frequency Increment or Decrement - Serial Interface Mode and GPIO Mode
      3. 7.3.3 Clock Distribution
        1. 7.3.3.1 Glitchless Operation
        2. 7.3.3.2 Divider Synchronization
        3. 7.3.3.3 Global and Individual Output Enable
      4. 7.3.4 Power Supplies and Power Management
      5. 7.3.5 Control Pins
    4. 7.4 Device Functional Modes
      1. 7.4.1 Operation Modes
        1. 7.4.1.1 Fall-Back Mode
        2. 7.4.1.2 Pin Mode
        3. 7.4.1.3 Serial Interface Mode
    5. 7.5 Programming
      1. 7.5.1 I2C Serial Interface
      2. 7.5.2 EEPROM
        1. 7.5.2.1 EEPROM - Cyclic Redundancy Check
        2. 7.5.2.2 Recommended Programming Procedure
        3. 7.5.2.3 EEPROM Access
          1. 7.5.2.3.1 Register Commit Flow
          2. 7.5.2.3.2 Direct Access Flow
        4. 7.5.2.4 Register Bits to EEPROM Mapping
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
      1. 8.3.1 Power-Up Sequence
      2. 8.3.2 Decoupling
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Examples
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Development Support
      2. 9.1.2 Device Nomenclature
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 Receiving Notification of Documentation Updates
    4. 9.4 Support Resources
    5. 9.5 Trademarks
    6. 9.6 Electrostatic Discharge Caution
    7. 9.7 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information
    1. 11.1 Package Option Addendum
    2. 11.2 Tape and Reel Information
7.5.2.3.1 Register Commit Flow

In the Register Commit flow, all bits from the device registers are copied into the EEPROM. The recommended flow is:

  1. Pre-configure the device as desired, except the serial interface using mode.
  2. Write 1 to RECAL to calibrate the VCO in this operation mode.
  3. Select the EEPROM page, to copy the register settings into, using REGCOMMIT_PAGE.
  4. Unlock the EEPROM for write access with EE_LOCK = x5.
  5. Start the register commit operation by writing 1 to REGCOMMIT.
  6. Force a CRC update by writing a 1 to UPDATE_CRC.
  7. Read back the calculated CRC in NVMLCRC.
  8. Store the read CRC value in the EEPROM by writing 0x3F to NVM_WR_ADDR and then the CRC value to NVM_WR_DATA.