SNVSCT1A October   2025  – December 2025 LM5066H

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 PMBus Interface Timing Characteristics
    8. 6.8 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Current Limit
      2. 7.3.2  Foldback Current Limit
      3. 7.3.3  Soft Start Disconnect (SFT_STRT)
      4. 7.3.4  Circuit Breaker
      5. 7.3.5  Power Limit
      6. 7.3.6  UVLO
      7. 7.3.7  OVLO
      8. 7.3.8  Power Good
      9. 7.3.9  VDD Sub-Regulator
      10. 7.3.10 Remote Temperature Sensing
      11. 7.3.11 Damaged MOSFET Detection
      12. 7.3.12 Analog Current Monitor (IMON)
    4. 7.4 Device Functional Modes
      1. 7.4.1 Power Up Sequence
      2. 7.4.2 Gate Control
      3. 7.4.3 Fault Timer and Restart
      4. 7.4.4 Shutdown Control
      5. 7.4.5 Enabling/Disabling and Resetting
    5. 7.5 Programming
      1. 7.5.1 PMBus Command Support
      2. 7.5.2 Detailed Descriptions of PMBus Commands
        1. 7.5.2.1  OPERATION (01h, Read/Write Byte)
        2. 7.5.2.2  CLEAR_FAULTS (03h, Send Byte)
        3. 7.5.2.3  WRITE_PROTECT (10h, Read/Write Byte)
        4. 7.5.2.4  RESTORE_FACTORY_DEFAULTS (12h, Send Byte)
        5. 7.5.2.5  STORE_USER_ALL (15h, Send Byte)
        6. 7.5.2.6  RESTORE_USER_ALL (16h, Send Byte)
        7. 7.5.2.7  CAPABILITY (19h, Read Byte)
        8. 7.5.2.8  VOUT_UV_WARN_LIMIT (43h, Read/Write Word)
        9. 7.5.2.9  OT_FAULT_LIMIT (4Fh, Read/Write Word)
        10. 7.5.2.10 OT_WARN_LIMIT (51h, Read/Write Word)
        11. 7.5.2.11 VIN_OV_WARN_LIMIT (57h, Read/Write Word)
        12. 7.5.2.12 IIN_OC_WARN_LIMIT (5Dh, Read/Write Word)
        13. 7.5.2.13 STATUS_BYTE (78h, Read Byte)
        14. 7.5.2.14 STATUS_WORD (79h, Read Word)
        15. 7.5.2.15 STATUS_VOUT (7Ah, Read Byte)
        16. 7.5.2.16 STATUS_INPUT (7Ch, Read Byte)
        17. 7.5.2.17 STATUS_TEMPERATURE (7Dh, Read Byte)
        18. 7.5.2.18 STATUS_CML (7Eh, Read Byte)
        19. 7.5.2.19 STATUS_OTHER (7Fh, Read Byte)
        20. 7.5.2.20 STATUS_MFR_SPECIFIC (80h)
        21. 7.5.2.21 READ_EIN (86h, Block Read)
        22. 7.5.2.22 READ_VIN (88h, Read Word)
        23. 7.5.2.23 READ_IIN (89h, Read Word)
        24. 7.5.2.24 READ_VOUT (8Bh, Read Word)
        25. 7.5.2.25 READ_IOUT (8Ch, Read Word)
        26. 7.5.2.26 READ_TEMPERATURE_1 (8Dh, Read Word)
        27. 7.5.2.27 READ_POUT (96h, Read Word)
        28. 7.5.2.28 READ_PIN (97h, Read Word)
        29. 7.5.2.29 PMBUS_REVISION (98h, Read Byte)
        30. 7.5.2.30 MFR_ID (99h, Block Read)
        31. 7.5.2.31 MFR_MODEL (9Ah, Block Read)
        32. 7.5.2.32 MFR_REVISION (9Bh, Block Read)
        33. 7.5.2.33 USER_DATA (BCh, Read/Write Byte)
        34. 7.5.2.34 READ_VIN_MIN (A0h, Read Word)
        35. 7.5.2.35 READ_VIN_PEAK (A1h, Read Word)
        36. 7.5.2.36 READ_IIN_PEAK (A2h, Read Word)
        37. 7.5.2.37 READ_PIN_PEAK (A3h)
        38. 7.5.2.38 READ_VOUT_MIN (A4h, Read Word)
        39. 7.5.2.39 READ_TEMP_AVG (C7h, Read Word)
        40. 7.5.2.40 READ_TEMP_PEAK (C8h, Read Word)
        41. 7.5.2.41 READ_SAMPLE_BUF (C9h, Block Read)
        42. 7.5.2.42 POWER_CYCLE (CAh, Send Byte)
        43. 7.5.2.43 READ_VAUX (D0h, Read Word)
        44. 7.5.2.44 MFR_READ_IIN (D1h, Read Word)
        45. 7.5.2.45 MFR_READ_PIN (D2h)
        46. 7.5.2.46 MFR_IIN_OC_WARN_LIMIT (D3h, F8h, Read/Write Word)
        47. 7.5.2.47 MFR_PIN_OP_WARN_LIMIT (D4h, Read/Write Word)
        48. 7.5.2.48 CLEAR_PIN_PEAK (D6h, Send Byte)
        49. 7.5.2.49 GATE_MASK (D7h, Read/Write Byte)
        50. 7.5.2.50 ALERT_MASK (D8h, Read/Write Word)
        51. 7.5.2.51 READ_VAUX_AVG (D9h, Read Word)
        52. 7.5.2.52 BLOCK_READ (DAh, Block Read)
        53. 7.5.2.53 SAMPLES_FOR_AVG (DBh, Read/Write Byte)
        54. 7.5.2.54 READ_VIN_AVG (DCh, Read Word)
        55. 7.5.2.55 READ_VOUT_AVG (DDh, Read Word)
        56. 7.5.2.56 READ_IIN_AVG (DEh, Read Word)
        57. 7.5.2.57 READ_PIN_AVG (DFh, Read Word)
        58. 7.5.2.58 CLEAR_BB_RAM (E0h, Send Byte)
        59. 7.5.2.59 READ_DIAGNOSTIC_WORD (E1h, Read Word)
        60. 7.5.2.60 AVG_BLOCK_READ (E2h, Block Read)
        61. 7.5.2.61 BB_ERASE (E3h, Send Byte)
        62. 7.5.2.62 BB_CONFIG (E4h, Read/Write Byte)
        63. 7.5.2.63 OC_BLANKING_TIMERS (E5h, Read/Write Byte)
        64. 7.5.2.64 DELAY_CONFIG (E7h, Read/Write Byte)
        65. 7.5.2.65 WD_PLB_ TIMER (E8h, Read/Write Byte)
        66. 7.5.2.66 PK_MIN_AVG (E9h, Read/Write Byte)
        67. 7.5.2.67 P2t TIMER (EAh, Read/Write Byte)
        68. 7.5.2.68 FETCH_BB_EEPROM (EBh, Send Byte)
        69. 7.5.2.69 READ_BB_RAM (ECh, Block Read)
        70. 7.5.2.70 ADC_CONFIG_1 (EDh, Read/Write Byte)
        71. 7.5.2.71 ADC_CONFIG_2 (EEh, Read/Write Byte)
        72. 7.5.2.72 DEVICE_SETUP1 (CCh, Read/Write Byte)
        73. 7.5.2.73 DEVICE_SETUP2 (EFh, Read/Write Byte)
        74. 7.5.2.74 DEVICE_SETUP3 (F0h, Read/Write Byte)
        75. 7.5.2.75 DEVICE_SETUP4 (CDh, Read/Write Byte)
        76. 7.5.2.76 DEVICE_SETUP5 (CEh, Read/Write Byte)
        77. 7.5.2.77 IIN OFFSET CALIBRATION (F2h, Read/Write Byte)
        78. 7.5.2.78 STATUS_MFR_SPECIFIC_2 (F3h, Read Word)
        79. 7.5.2.79 READ_BB_EEPROM (F4h, Block Read)
        80. 7.5.2.80 BB_TIMER (F6h, Read Byte)
        81. 7.5.2.81 PMBUS_ADDR (F7h, Read/Write Byte)
      3. 7.5.3 Reading and Writing Telemetry Data and Warning Thresholds
      4. 7.5.4 Determining Telemetry Coefficients Empirically With Linear Fit
      5. 7.5.5 Writing Telemetry Data
      6. 7.5.6 PMBus Address Lines (ADR0, ADR1, ADR2)
      7. 7.5.7 SMBA Response
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 54V, 100A PMBus Hot Swap Design
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design-In Procedure
          1. 8.2.1.2.1 Selecting the Hotswap FETs
          2. 8.2.1.2.2 dv/dt based Start-Up
            1. 8.2.1.2.2.1 Choosing the VOUT Slew Rate
          3. 8.2.1.2.3 Select RSNS and CL Setting
          4. 8.2.1.2.4 Select Power Limit
          5. 8.2.1.2.5 Set Fault Timer
          6. 8.2.1.2.6 Check MOSFET SOA
          7. 8.2.1.2.7 Set UVLO and OVLO Thresholds
            1. 8.2.1.2.7.1 Option A
            2. 8.2.1.2.7.2 Option B
            3. 8.2.1.2.7.3 Option C
            4. 8.2.1.2.7.4 Option D
          8. 8.2.1.2.8 Power Good Pin
          9. 8.2.1.2.9 Input and Output Protection
        3. 8.2.1.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Third-Party Products Disclaimer
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

7.5.2.35 READ_VIN_PEAK (A1h, Read Word)

The READ_VIN_PEAK command is a standard PMBus command that returns the 12-bit peak input voltage measured since a power-on reset or the last RESET_PEAK (Bit[7] in the PK_MIN_AVG register) made high. Reading this register should use the coefficients shown in Table 7-72. Accesses to this command should use the PMBus read word protocol.

Table 7-32 READ_VIN_PEAK Register Description
BitName

Description

Minimum Value

Maximum Value

Default

15:0

READ_VIN_PEAK

Value measured for peak input voltage since reset or last clear

0x0000 (0V)

0x0FFF (89.1V)

0x0000 (0V)