SNVSCT1A October   2025  ā€“ December 2025 LM5066H

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 PMBus Interface Timing Characteristics
    8. 6.8 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Current Limit
      2. 7.3.2  Foldback Current Limit
      3. 7.3.3  Soft Start Disconnect (SFT_STRT)
      4. 7.3.4  Circuit Breaker
      5. 7.3.5  Power Limit
      6. 7.3.6  UVLO
      7. 7.3.7  OVLO
      8. 7.3.8  Power Good
      9. 7.3.9  VDD Sub-Regulator
      10. 7.3.10 Remote Temperature Sensing
      11. 7.3.11 Damaged MOSFET Detection
      12. 7.3.12 Analog Current Monitor (IMON)
    4. 7.4 Device Functional Modes
      1. 7.4.1 Power Up Sequence
      2. 7.4.2 Gate Control
      3. 7.4.3 Fault Timer and Restart
      4. 7.4.4 Shutdown Control
      5. 7.4.5 Enabling/Disabling and Resetting
    5. 7.5 Programming
      1. 7.5.1 PMBus Command Support
      2. 7.5.2 Detailed Descriptions of PMBus Commands
        1. 7.5.2.1  OPERATION (01h, Read/Write Byte)
        2. 7.5.2.2  CLEAR_FAULTS (03h, Send Byte)
        3. 7.5.2.3  WRITE_PROTECT (10h, Read/Write Byte)
        4. 7.5.2.4  RESTORE_FACTORY_DEFAULTS (12h, Send Byte)
        5. 7.5.2.5  STORE_USER_ALL (15h, Send Byte)
        6. 7.5.2.6  RESTORE_USER_ALL (16h, Send Byte)
        7. 7.5.2.7  CAPABILITY (19h, Read Byte)
        8. 7.5.2.8  VOUT_UV_WARN_LIMIT (43h, Read/Write Word)
        9. 7.5.2.9  OT_FAULT_LIMIT (4Fh, Read/Write Word)
        10. 7.5.2.10 OT_WARN_LIMIT (51h, Read/Write Word)
        11. 7.5.2.11 VIN_OV_WARN_LIMIT (57h, Read/Write Word)
        12. 7.5.2.12 IIN_OC_WARN_LIMIT (5Dh, Read/Write Word)
        13. 7.5.2.13 STATUS_BYTE (78h, Read Byte)
        14. 7.5.2.14 STATUS_WORD (79h, Read Word)
        15. 7.5.2.15 STATUS_VOUT (7Ah, Read Byte)
        16. 7.5.2.16 STATUS_INPUT (7Ch, Read Byte)
        17. 7.5.2.17 STATUS_TEMPERATURE (7Dh, Read Byte)
        18. 7.5.2.18 STATUS_CML (7Eh, Read Byte)
        19. 7.5.2.19 STATUS_OTHER (7Fh, Read Byte)
        20. 7.5.2.20 STATUS_MFR_SPECIFIC (80h)
        21. 7.5.2.21 READ_EIN (86h, Block Read)
        22. 7.5.2.22 READ_VIN (88h, Read Word)
        23. 7.5.2.23 READ_IIN (89h, Read Word)
        24. 7.5.2.24 READ_VOUT (8Bh, Read Word)
        25. 7.5.2.25 READ_IOUT (8Ch, Read Word)
        26. 7.5.2.26 READ_TEMPERATURE_1 (8Dh, Read Word)
        27. 7.5.2.27 READ_POUT (96h, Read Word)
        28. 7.5.2.28 READ_PIN (97h, Read Word)
        29. 7.5.2.29 PMBUS_REVISION (98h, Read Byte)
        30. 7.5.2.30 MFR_ID (99h, Block Read)
        31. 7.5.2.31 MFR_MODEL (9Ah, Block Read)
        32. 7.5.2.32 MFR_REVISION (9Bh, Block Read)
        33. 7.5.2.33 USER_DATA (BCh, Read/Write Byte)
        34. 7.5.2.34 READ_VIN_MIN (A0h, Read Word)
        35. 7.5.2.35 READ_VIN_PEAK (A1h, Read Word)
        36. 7.5.2.36 READ_IIN_PEAK (A2h, Read Word)
        37. 7.5.2.37 READ_PIN_PEAK (A3h)
        38. 7.5.2.38 READ_VOUT_MIN (A4h, Read Word)
        39. 7.5.2.39 READ_TEMP_AVG (C7h, Read Word)
        40. 7.5.2.40 READ_TEMP_PEAK (C8h, Read Word)
        41. 7.5.2.41 READ_SAMPLE_BUF (C9h, Block Read)
        42. 7.5.2.42 POWER_CYCLE (CAh, Send Byte)
        43. 7.5.2.43 READ_VAUX (D0h, Read Word)
        44. 7.5.2.44 MFR_READ_IIN (D1h, Read Word)
        45. 7.5.2.45 MFR_READ_PIN (D2h)
        46. 7.5.2.46 MFR_IIN_OC_WARN_LIMIT (D3h, F8h, Read/Write Word)
        47. 7.5.2.47 MFR_PIN_OP_WARN_LIMIT (D4h, Read/Write Word)
        48. 7.5.2.48 CLEAR_PIN_PEAK (D6h, Send Byte)
        49. 7.5.2.49 GATE_MASK (D7h, Read/Write Byte)
        50. 7.5.2.50 ALERT_MASK (D8h, Read/Write Word)
        51. 7.5.2.51 READ_VAUX_AVG (D9h, Read Word)
        52. 7.5.2.52 BLOCK_READ (DAh, Block Read)
        53. 7.5.2.53 SAMPLES_FOR_AVG (DBh, Read/Write Byte)
        54. 7.5.2.54 READ_VIN_AVG (DCh, Read Word)
        55. 7.5.2.55 READ_VOUT_AVG (DDh, Read Word)
        56. 7.5.2.56 READ_IIN_AVG (DEh, Read Word)
        57. 7.5.2.57 READ_PIN_AVG (DFh, Read Word)
        58. 7.5.2.58 CLEAR_BB_RAM (E0h, Send Byte)
        59. 7.5.2.59 READ_DIAGNOSTIC_WORD (E1h, Read Word)
        60. 7.5.2.60 AVG_BLOCK_READ (E2h, Block Read)
        61. 7.5.2.61 BB_ERASE (E3h, Send Byte)
        62. 7.5.2.62 BB_CONFIG (E4h, Read/Write Byte)
        63. 7.5.2.63 OC_BLANKING_TIMERS (E5h, Read/Write Byte)
        64. 7.5.2.64 DELAY_CONFIG (E7h, Read/Write Byte)
        65. 7.5.2.65 WD_PLB_ TIMER (E8h, Read/Write Byte)
        66. 7.5.2.66 PK_MIN_AVG (E9h, Read/Write Byte)
        67. 7.5.2.67 P2t TIMER (EAh, Read/Write Byte)
        68. 7.5.2.68 FETCH_BB_EEPROM (EBh, Send Byte)
        69. 7.5.2.69 READ_BB_RAM (ECh, Block Read)
        70. 7.5.2.70 ADC_CONFIG_1 (EDh, Read/Write Byte)
        71. 7.5.2.71 ADC_CONFIG_2 (EEh, Read/Write Byte)
        72. 7.5.2.72 DEVICE_SETUP1 (CCh, Read/Write Byte)
        73. 7.5.2.73 DEVICE_SETUP2 (EFh, Read/Write Byte)
        74. 7.5.2.74 DEVICE_SETUP3 (F0h, Read/Write Byte)
        75. 7.5.2.75 DEVICE_SETUP4 (CDh, Read/Write Byte)
        76. 7.5.2.76 DEVICE_SETUP5 (CEh, Read/Write Byte)
        77. 7.5.2.77 IIN OFFSET CALIBRATION (F2h, Read/Write Byte)
        78. 7.5.2.78 STATUS_MFR_SPECIFIC_2 (F3h, Read Word)
        79. 7.5.2.79 READ_BB_EEPROM (F4h, Block Read)
        80. 7.5.2.80 BB_TIMER (F6h, Read Byte)
        81. 7.5.2.81 PMBUS_ADDR (F7h, Read/Write Byte)
      3. 7.5.3 Reading and Writing Telemetry Data and Warning Thresholds
      4. 7.5.4 Determining Telemetry Coefficients Empirically With Linear Fit
      5. 7.5.5 Writing Telemetry Data
      6. 7.5.6 PMBus Address Lines (ADR0, ADR1, ADR2)
      7. 7.5.7 SMBA Response
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 54V, 100A PMBus Hot Swap Design
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design-In Procedure
          1. 8.2.1.2.1 Selecting the Hotswap FETs
          2. 8.2.1.2.2 dv/dt based Start-Up
            1. 8.2.1.2.2.1 Choosing the VOUT Slew Rate
          3. 8.2.1.2.3 Select RSNS and CL Setting
          4. 8.2.1.2.4 Select Power Limit
          5. 8.2.1.2.5 Set Fault Timer
          6. 8.2.1.2.6 Check MOSFET SOA
          7. 8.2.1.2.7 Set UVLO and OVLO Thresholds
            1. 8.2.1.2.7.1 Option A
            2. 8.2.1.2.7.2 Option B
            3. 8.2.1.2.7.3 Option C
            4. 8.2.1.2.7.4 Option D
          8. 8.2.1.2.8 Power Good Pin
          9. 8.2.1.2.9 Input and Output Protection
        3. 8.2.1.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Third-Party Products Disclaimer
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

SMBA Response

The SMBA effectively has two masks:

  • The alert mask register at D8h
  • The ARA automatic mask.

The ARA automatic mask is a mask that is set in response to a successful ARA read. An ARA read operation returns the PMBus address of the lowest addressed part on the bus that has its SMBA asserted. A successful ARA read means that this part was the one that returned its address. When a part responds to the ARA read, it releases the SMBA signal. When the last part on the bus that has an SMBA set has successfully reported its address, the SMBA signal de-asserts.

The way that the LM5066Hx releases the SMBA signal is by setting the ARA automatic mask bit for all fault conditions present at the time of the ARA read. All status registers will still the fault condition, but it does not generate a SMBA on that fault again until the ARA automatic mask is cleared by the host issuing a CLEAR_FAULTS command to this part. This should be done as a routine part of servicing an SMBA condition on a part, even if the ARA read is not done. Figure 7-9 depicts a schematic version of this flow.

LM5066H Typical Flow Schematic for SMBA FaultFigure 7-9 Typical Flow Schematic for SMBA Fault