Produktdetails

Number of full bridges 1 Vs (min) (V) 4.5 Vs ABS (max) (V) 40 Peak output current (A) 32 RDS(ON) (HS + LS) (mΩ) 30 Sleep current (µA) 5 Control mode Independent 1/2-Bridge, PH/EN, PWM Control interface Hardware (GPIO), SPI Features Current Regulation, Current sense Amplifier, Integrated Current Sensing, Open-Load Detection Topology Integrated FET Rating Automotive TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 125
Number of full bridges 1 Vs (min) (V) 4.5 Vs ABS (max) (V) 40 Peak output current (A) 32 RDS(ON) (HS + LS) (mΩ) 30 Sleep current (µA) 5 Control mode Independent 1/2-Bridge, PH/EN, PWM Control interface Hardware (GPIO), SPI Features Current Regulation, Current sense Amplifier, Integrated Current Sensing, Open-Load Detection Topology Integrated FET Rating Automotive TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 125
HTSSOP (PWP) 28 62.08 mm² (9.7 mm × 6.4 mm) VQFN-HR (RXZ) 16 19.25 mm² (3.5 mm × 5.5 mm)
  • AEC-Q100 qualified for automotive applications:
    • Temperature grade 1: –40°C to +125°C, TA
  • Functional Safety-Capable
  • 4.5V to 35V (40V abs. max) operating range
  • VQFN-HR package: RON_LS + RON_HS: 32mΩ
  • HTSSOP package: RON_LS + RON_HS: 40mΩ
  • IOUT Max = 32A
  • PWM frequency operation up to 25KHz with automatic dead time assertion
  • Configurable slew rate and spread spectrum clocking for low electromagnetic interference (EMI)
  • Integrated current sense (eliminates shunt resistor)
  • Proportional load current output on IPROPI pin
  • Configurable current regulation
  • Protection and diagnostic features with configurable fault reaction (latched or retry)
    • Load diagnostics in both the off-state and on-state to detect open load and short circuit
    • Voltage monitoring on supply (VM)
    • Over current protection
    • Over temperature protection
    • Fault indication on nFAULT pin
  • Supports 3.3V, 5V logic inputs
  • Low sleep current - 1µA typical at 25°C
  • 3 variants - HW (H), SPI (S) or SPI (P)
  • Configurable control modes:
    • Single full bridge using PWM or PH/EN mode
    • Two half-bridges using Independent mode
  • Device family comparison table
  • AEC-Q100 qualified for automotive applications:
    • Temperature grade 1: –40°C to +125°C, TA
  • Functional Safety-Capable
  • 4.5V to 35V (40V abs. max) operating range
  • VQFN-HR package: RON_LS + RON_HS: 32mΩ
  • HTSSOP package: RON_LS + RON_HS: 40mΩ
  • IOUT Max = 32A
  • PWM frequency operation up to 25KHz with automatic dead time assertion
  • Configurable slew rate and spread spectrum clocking for low electromagnetic interference (EMI)
  • Integrated current sense (eliminates shunt resistor)
  • Proportional load current output on IPROPI pin
  • Configurable current regulation
  • Protection and diagnostic features with configurable fault reaction (latched or retry)
    • Load diagnostics in both the off-state and on-state to detect open load and short circuit
    • Voltage monitoring on supply (VM)
    • Over current protection
    • Over temperature protection
    • Fault indication on nFAULT pin
  • Supports 3.3V, 5V logic inputs
  • Low sleep current - 1µA typical at 25°C
  • 3 variants - HW (H), SPI (S) or SPI (P)
  • Configurable control modes:
    • Single full bridge using PWM or PH/EN mode
    • Two half-bridges using Independent mode
  • Device family comparison table

The DRV824x-Q1 family of devices is a fully integrated H-bridge driver intended for a wide range of automotive applications. The device can be configured as a single full-bridge driver or as two independent half-bridge drivers. Designed in a BiCMOS high power process technology node, this monolithic family of devices in a power package offer excellent power handling and thermal capability while providing compact package size, ease of layout, EMI control, accurate current sense, robustness, and diagnostic capability. This family provides an identical pin function with scalable RON (current capability) to support different loads.

The devices integrate a N-Channel H-bridge, charge pump regulator, high-side current sensing with regulation, current proportional output, and protection circuitry. A low-power sleep mode is provided to achieve low quiescent current. The devices offer voltage monitoring and load diagnostics as well as protection features against over current and over temperature. Fault conditions are indicated on nFAULT pin. The devices are available in three variants - hardwired interface: HW (H) and two SPI variants: SPI(P) and SPI(S), with SPI (P) for externally supplied logic supply and SPI (S) for internally generated logic supply. The SPI variants offer more flexibility in device configuration and fault observability.

The DRV824x-Q1 family of devices is a fully integrated H-bridge driver intended for a wide range of automotive applications. The device can be configured as a single full-bridge driver or as two independent half-bridge drivers. Designed in a BiCMOS high power process technology node, this monolithic family of devices in a power package offer excellent power handling and thermal capability while providing compact package size, ease of layout, EMI control, accurate current sense, robustness, and diagnostic capability. This family provides an identical pin function with scalable RON (current capability) to support different loads.

The devices integrate a N-Channel H-bridge, charge pump regulator, high-side current sensing with regulation, current proportional output, and protection circuitry. A low-power sleep mode is provided to achieve low quiescent current. The devices offer voltage monitoring and load diagnostics as well as protection features against over current and over temperature. Fault conditions are indicated on nFAULT pin. The devices are available in three variants - hardwired interface: HW (H) and two SPI variants: SPI(P) and SPI(S), with SPI (P) for externally supplied logic supply and SPI (S) for internally generated logic supply. The SPI variants offer more flexibility in device configuration and fault observability.

Herunterladen Video mit Transkript ansehen Video

Ähnliche Produkte, die für Sie interessant sein könnten

Selbe Funktionalität wie der verglichene Baustein bei abweichender Anschlussbelegung.
DRV8243-Q1 AKTIV 12-A-H-Brücken-Treiber, 40 V, für die Automobilindustrie, mit integrierter Strommessung und Stromsen High power auto H-bridge driver w/ diagnostics and internal CSA
DRV8706-Q1 AKTIV Intelligenter 40 V-H-Brücken-Gate-Treiber mit Offline-Diagnose und Inline-Strommessverstärker für Automotive 40-V H-bridge smart gate driver with offline diagnostics and inline current sense amplifier
DRV8244-Q1 AKTIV 21-A-H-Brücken-Treiber, 40 V, für die Automobilindustrie, mit integrierter Strommessung und Stromsen High power auto H-bridge driver w/ diagnostics and internal CSA
DRV8873-Q1 AKTIV 10-A-H-Brücken-Motortreiber, 40 V, Automobilindustrie, mit integrierter Stromsensorrückkopplung H-bridge integrated driver with integrated current sensing
Ähnliche Funktionalität wie der verglichene Baustein.
DRV8106-Q1 AKTIV Intell. 40 V-Halbbrücken-Gate-Treiber, Offline-Diagnose u. Inline-Strommessverstärker für Auto.ind. Automotive, 40-V, half-bridge Smart Gate Driver w/offline diagnostics and inline current sense amp.

Technische Dokumentation

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Evaluierungsplatine

DRV8245H-Q1EVM — DRV8245-Q1 Evaluierungsmodul für H-Brückentreiber mit Hardware-Schnittstelle, für die Automobilindus

Die Bausteinfamilie DRV824x-Q1 ist ein vollständig integrierter H-Brückentreiber für ein breites Spektrum von Automobilanwendungen. Der DRV824x-Q1-Baustein kann als einzelner H-Brückentreiber und als zwei unabhängige Halbbrückentreiber konfiguriert werden. Dieser monolithische Chip-Baustein in (...)

Benutzerhandbuch: PDF | HTML
Unterstützte Produkte und Hardware
Vorrätig
Limit:
??asset.out-of-stock-ti_de_DE??
Nicht verfügbar
Evaluierungsplatine

DRV8245S-Q1LEVM — DRV8245–Q1 H-Brückentreiber-Evaluierungsmodul mit SPI-Schnittstelle für die Automobilindustrie

Die Bausteinfamilie DRV824x-Q1 ist ein vollständig integrierter H-Brückentreiber für ein breites Spektrum von Automobilanwendungen. Der DRV824x-Q1-Baustein kann als einzelner H-Brückentreiber und als zwei unabhängige Halbbrückentreiber konfiguriert werden. Dieser monolithische Chip-Baustein in (...)

Benutzerhandbuch: PDF | HTML
Unterstützte Produkte und Hardware
Vorrätig
Limit:
??asset.out-of-stock-ti_de_DE??
Nicht verfügbar
Simulationsmodell

DRV8245HPWPQ1 PSpice Unencrypted Transient Model

SLVMDV5.ZIP (199 KB) - PSpice-Modell
Unterstützte Produkte und Hardware
Simulationsmodell

DRV8245PPWPQ1 PSpice Unencrypted Transient Model

SLVMDV6.ZIP (208 KB) - PSpice-Modell
Unterstützte Produkte und Hardware
Simulationsmodell

DRV8245SPWPQ1 PSpice Unencrypted Transient Model

SLVMDV4.ZIP (205 KB) - PSpice-Modell
Unterstützte Produkte und Hardware
Berechnungstool

SLVRBI3 — Full Bridge Driver Junction Temperature Estimator

Unterstützte Produkte und Hardware
Referenzdesign

TIDA-020079 — Zonen-Referenzdesign

Dieses Referenzdesign demonstriert die wichtigsten Funktionen von Zonensteuermodulen der nächsten Generation, einschließlich Stromverteilung, Lastansteuerung und Vernetzung im Fahrzeug. Das Design umfasst PMIC- und Mikrocontroller-Designs (MCU), die mit funktionaler Sicherheit konform sind, (...)
Unterstützte Produkte und Hardware
Referenzdesign

TIDA-020094 — 48-V-Zonenreferenzdesign

Dieses Referenzdesign demonstriert Trends bei fortschrittlichen 48-V-Niederspannungsschienenarchitekturen für die Automobilindustrie. Das Design umfasst die 48-V-Backbone-Architektur und Leistungsumwandlung von 48 V zu 12 V. Das Referenzdesign hebt 48-V-Lasttreiber in wichtigen Produkten hervor. (...)

Unterstützte Produkte und Hardware
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
HTSSOP (PWP) 28 Ultra Librarian
VQFN-HR (RXZ) 16 Ultra Librarian

Bestellen & Qualität

Empfohlene Produkte können Parameter, Evaluierungsmodule oder Referenzdesigns zu diesem TI-Produkt beinhalten.

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos