TMAG5170
Hochpräziser linearer 3D-Hall-Effekt-Sensor mit SPI-Bus-Schnittstelle
TMAG5170
- High-precision linear 3D Hall-effect sensor to optimize position sensing speed and accuracy:
- Linear measurement total error: ±2.6% (maximum at 25°C)
- Sensitivity temperature drift: ±2.8% (maximum)
- 20-Ksps conversion rate for single axis
- 10-MHz serial peripheral interface (SPI) with cyclic redundancy check (CRC)
- Built-in temperature sensor with < ±2°C error
- Independently selectable X, Y, and Z magnetic ranges:
- TMAG5170A1: ±25, ±50, ±100 mT
- TMAG5170A2: ±75, ±150, ±300 mT
- 5-nA (typical) deep sleep mode current
- Autonomous wake-up and sleep mode for threshold detection consuming only 1.5 µA
- ALERT function to initiate sensor conversion or indicate conversion complete
- Integrated diagnostics for fault detection
- Integrated angle CORDIC calculation with gain and offset adjustment
- 2.3-V to 5.5-V supply voltage range
- Operating temperature range: –40°C to +150°C
The TMAG5170 is a high-precision linear 3D Hall-effect sensor designed for a wide range of industrial and personal electronics applications. The high level of integration offers flexibility and accuracy in a variety of position sensing systems. This device features 3 independent Hall sensors at X, Y, and Z axes.
A precision signal-chain along with an integrated 12-bit ADC enables high accuracy and low drift magnetic field measurements while supporting a sampling of up to 20 ksps. On-chip temperature sensor data is available for system-level drift compensation.
Integrated angle calculation engine (CORDIC) provides full 360° angular position information for both on-axis and off-axis angle measurement topologies. The angle calculation is performed using two user-selected magnetic axes. The device features magnetic gain and offset correction to mitigate the impact of system mechanical error sources.
The TMAG5170 can be configured through the SPI to enable any combination of magnetic axes and temperature measurements. Multiple sensor conversion schemes and SPI read frames help optimize throughput and accuracy. A dedicated ALERT pin can act as a system interrupt during low power wake-up and sleep mode, and can also be used by a microcontroller to trigger a new sensor conversion.
The TMAG5170 offers multiple diagnostics features to detect and report both system and device-level failures. The SPI communication features a user-enabled cyclic redundancy check to enhance the data integrity.
The device is offered in two different orderables to support wide magnetic fields ranges from ±25mT to ±300mT.
The device performs consistently across a wide ambient temperature range of –40°C to +150°C.
TMAG5170 belegte den zweiten Platz in der Kategorie „Produkt des Jahres“ von Elektronik in der Kategorie „Messung und Sensorik“.
Technische Dokumentation
Design und Entwicklung
Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.
TMAG5170UEVM — TMAG5170-Evaluierungsmodul für hochpräzisen, linearen 3D-Hall-Effekt-Sensor mit und SPI-Bus-Schnitts
HALL-PROXIMITY-DESIGN — Magnetic Sensing Proximity Tool
HALL-PROXIMITY-DESIGN is a software tool that facilitates rapid iterative design for magnet and Hall-effect sensor systems.
Unterstützte Produkte und Hardware
Produkte
Mehrachsige lineare und Winkelpositionssensoren
Lineare Hall-Effekt-Sensoren
Hall-Effekt-Latches & ‑Schalter
Hardware-Entwicklung
Evaluierungsplatine
Software
Berechnungstool
SBAR012 — Angle Error Calculator for Linear 3D Hall-effect Sensors
Unterstützte Produkte und Hardware
Produkte
Mehrachsige lineare und Winkelpositionssensoren
TI-MAGNETIC-SENSE-SIMULATOR — TI Magnetic sensing simulation tool
The TI-MAGNETIC-SENSE-SIMULATOR (TIMSS) webtool estimates magnetic flux density and TI magnetic sensor outputs for magnetic position sensing systems. The tool has device emulation and supports various magnet shapes, grades and motion types.
Unterstützte Produkte und Hardware
Produkte
Hall-Effekt-Latches & ‑Schalter
Lineare Hall-Effekt-Sensoren
Mehrachsige lineare und Winkelpositionssensoren
Hardware-Entwicklung
Software
Berechnungstool
TIDA-060040 — Referenzdesign für Absolutwinkel-Encoder mit Hall-Effekt-Sensoren zur präzisen Motorpositionssteueru
Gehäuse | Pins | Herunterladen |
---|---|---|
VSSOP (DGK) | 8 | Optionen anzeigen |
Bestellen & Qualität
- RoHS
- REACH
- Bausteinkennzeichnung
- Blei-Finish/Ball-Material
- MSL-Rating / Spitzenrückfluss
- MTBF-/FIT-Schätzungen
- Materialinhalt
- Qualifikationszusammenfassung
- Kontinuierliches Zuverlässigkeitsmonitoring
- Werksstandort
- Montagestandort
Empfohlene Produkte können Parameter, Evaluierungsmodule oder Referenzdesigns zu diesem TI-Produkt beinhalten.
Support und Schulungen
TI E2E™-Foren mit technischem Support von TI-Ingenieuren
Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.
Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support.