Startseite Logik- & Spannungsumsetzung Spannungsumsetzer & Pegelverschieber Fest-Richtungs-Spannungsumsetzer
Startseite
Logik- & Spannungsumsetzung
Spannungsumsetzer & Pegelverschieber
Fest-Richtungs-Spannungsumsetzer
NEU

TXV0106

AKTIV

Dual-supply fixed-direction six-channel voltage translator

Jetzt bestellen
Datenblatt

TXV0106

AKTIV
Datenblatt Jetzt bestellen

Produktdetails

Technology family AVC Applications GPIO, JTAG, RGMII, SPI, UART Bits (#) 6 High input voltage (min) (V) 1.08 High input voltage (max) (V) 3.6 Vout (min) (V) 1.65 Vout (max) (V) 3.6 Data rate (max) (Mbps) 250 IOH (max) (mA) -12 IOL (max) (mA) 12 Supply current (max) (µA) 16 Features Output enable, Overvoltage tolerant inputs, Partial power down (Ioff), Vcc isolation Input type Standard CMOS Output type 3-State, Balanced CMOS, Push-Pull Rating Catalog Operating temperature range (°C) -40 to 125
Technology family AVC Applications GPIO, JTAG, RGMII, SPI, UART Bits (#) 6 High input voltage (min) (V) 1.08 High input voltage (max) (V) 3.6 Vout (min) (V) 1.65 Vout (max) (V) 3.6 Data rate (max) (Mbps) 250 IOH (max) (mA) -12 IOL (max) (mA) 12 Supply current (max) (µA) 16 Features Output enable, Overvoltage tolerant inputs, Partial power down (Ioff), Vcc isolation Input type Standard CMOS Output type 3-State, Balanced CMOS, Push-Pull Rating Catalog Operating temperature range (°C) -40 to 125
WQFN (BQB) 16 8.75 mm² 3.5 x 2.5

  • Configurable design allows each port to operate with a power supply range from 1.2 V to 3.6 V

  • Supports up to 500Mbps for 1.65 V to 3.6 V
  • Meets RGMII 2.0 timing specifications:
    • < 750 ps rise and fall time
    • < ± 5 % duty cycle distortion
    • < ± 400 ps channel to channel skew
    • Up to 250Mbps/channel
  • Integrated 10 Ω damping output resistor to minimize signal reflections
  • High drive strength (up to 12 mA at 3.6 V)
  • Fully configurable symmetric dual-rail design
  • Optimal signal integrity performance with 390ps peak-to-peak jitter for 1.8 V to 3.3 V
  • Features VCC isolation and VCC disconnect
  • Ioff supports partial-power-down mode operation
  • Latch-up performance exceeds 100 mA per JESD 78, Class II
  • ESD protection exceeds JESD 22:
    • 2000-V Human-Body Model
    • 1000-V Charged-Device Model
  • Low power consumption:
    • 10-µA maximum (25°C)
    • 20-µA maximum (–40°C to 125°C)
  • Operating temperature from –40°C to +125°C

  • Configurable design allows each port to operate with a power supply range from 1.2 V to 3.6 V

  • Supports up to 500Mbps for 1.65 V to 3.6 V
  • Meets RGMII 2.0 timing specifications:
    • < 750 ps rise and fall time
    • < ± 5 % duty cycle distortion
    • < ± 400 ps channel to channel skew
    • Up to 250Mbps/channel
  • Integrated 10 Ω damping output resistor to minimize signal reflections
  • High drive strength (up to 12 mA at 3.6 V)
  • Fully configurable symmetric dual-rail design
  • Optimal signal integrity performance with 390ps peak-to-peak jitter for 1.8 V to 3.3 V
  • Features VCC isolation and VCC disconnect
  • Ioff supports partial-power-down mode operation
  • Latch-up performance exceeds 100 mA per JESD 78, Class II
  • ESD protection exceeds JESD 22:
    • 2000-V Human-Body Model
    • 1000-V Charged-Device Model
  • Low power consumption:
    • 10-µA maximum (25°C)
    • 20-µA maximum (–40°C to 125°C)
  • Operating temperature from –40°C to +125°C

The TXV0106 is a 6-bit, dual-supply fixed-direction low-skew, low jitter voltage translation device. This device can be used for redriving, voltage translation and power isolation when implementing skew sensitive interface, such as RGMII between Ethernet MAC and PHY. The Ax I/O pins and enable pin (OE) are referenced to VCCA logic levels, and Bx I/O pins are referenced to VCCB logic levels. This device has improved channel-to-channel skew, duty cycle distortion and symmetric rise or fall timing for applications requiring strict timing conditions.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, thus preventing damaging current backflow through the device when it is powered down.

The VCC isolation feature is designed so that if either VCC supply is at or near 0V both ports will switch to a high-impedance state. This feature enables power isolation for communications across multiple MACs and PHYs, and is beneficial in situations where MACs and PHYs are powered up asynchronously preventing current backflow between devices.

The TXV0106 transmits data in a fixed direction from the A bus to the B bus. When OE is set to High, both Ax and Bx pins will be forced into a high-impedance state. See Device Functional Modes for a summary of the operation of the control logic.

The TXV0106 is a 6-bit, dual-supply fixed-direction low-skew, low jitter voltage translation device. This device can be used for redriving, voltage translation and power isolation when implementing skew sensitive interface, such as RGMII between Ethernet MAC and PHY. The Ax I/O pins and enable pin (OE) are referenced to VCCA logic levels, and Bx I/O pins are referenced to VCCB logic levels. This device has improved channel-to-channel skew, duty cycle distortion and symmetric rise or fall timing for applications requiring strict timing conditions.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, thus preventing damaging current backflow through the device when it is powered down.

The VCC isolation feature is designed so that if either VCC supply is at or near 0V both ports will switch to a high-impedance state. This feature enables power isolation for communications across multiple MACs and PHYs, and is beneficial in situations where MACs and PHYs are powered up asynchronously preventing current backflow between devices.

The TXV0106 transmits data in a fixed direction from the A bus to the B bus. When OE is set to High, both Ax and Bx pins will be forced into a high-impedance state. See Device Functional Modes for a summary of the operation of the control logic.
open-in-new Andere Fest-Richtungs-Spannungsumsetzer suchen
Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

star =Von TI ausgewählte Top-Empfehlungen für dieses Produkt
Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 6
Typ Titel Datum
* Data sheet TXV0106 6-Bit Fix Direction Low Skew, Low-Jitter Voltage Translator or Buffer datasheet (Rev. A) PDF | HTML 12 Apr 2024
Application brief Enabling AI Accelerators with Voltage Level Translation PDF | HTML 01 Mai 2024
EVM User's guide TXV010xEVM Evaluation Module User's Guide PDF | HTML 05 Feb 2024
Application note Overcoming Design Challenges - Implementing High Performance Interfaces PDF | HTML 12 Dez 2023
Application brief Supporting Time and Skew Sensitive Interfaces with TI's TXV Level-Shifter PDF | HTML 27 Okt 2023
Application brief Enabling Industrial and Automotive Ethernet RGMII Interfaces with Voltage Transl PDF | HTML 02 Aug 2023

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Evaluierungsplatine

14-24-NL-LOGIC-EVM — Generisches Logikprodukt-Evaluierungsmodul für 14- bis 24-polige bleifreie Gehäuse

14-24-NL-LOGIC-EVM ist ein flexibles Evaluierungsmodul (EVM), das alle Logik- oder Übersetzungsbausteine mit einem 14- bis 24-poligen BQA-, BQB-, RGY-, RSV-, RJW- oder RHL-Gehäuse unterstützt.

Benutzerhandbuch: PDF | HTML
Nicht verfügbar auf TI.com
Evaluierungsplatine

TXV0106-EVM — TXV0106 – Evaluierungsmodul

Das Evaluierungsmodul (EVM) TXV0106 ist eine benutzerfreundliche Plattform zur Evaluierung von Funktionen und der Leistung des TXV0106. Das EVM verfügt über optionale Schaltkreise und Jumper. Damit kann das Gerät für verschiedene Anwendungen konfiguriert werden. Das (...)
Benutzerhandbuch: PDF | HTML
Nicht verfügbar auf TI.com
Simulationsmodell

TXV0106 IBIS Model

SCEM797.ZIP (44 KB) - IBIS Model
Herunterladen
Gehäuse Pins Herunterladen
WQFN (BQB) 16 Optionen anzeigen
Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

Bestellen & Qualität

Beinhaltete Information:
  • RoHS
  • REACH
  • Bausteinkennzeichnung
  • Blei-Finish/Ball-Material
  • MSL-Rating / Spitzenrückfluss
  • MTBF-/FIT-Schätzungen
  • Materialinhalt
  • Qualifikationszusammenfassung
  • Kontinuierliches Zuverlässigkeitsmonitoring
Beinhaltete Information:
  • Werksstandort
  • Montagestandort

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Alle Forenthemen auf Englisch anzeigen

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos