TMS320F28052
- High-efficiency 32-bit CPU
(TMS320C28x)
- 60 MHz (16.67-ns cycle time)
- 16 × 16 and 32 × 32 Multiply and Accumulate (MAC) operations
- 16 × 16 dual MAC
- Harvard bus architecture
- Atomic operations
- Fast interrupt response and processing
- Unified memory programming model
- Code-efficient (in C/C++ and Assembly)
- Programmable Control Law
Accelerator (CLA)
- 32-bit floating-point math accelerator
- Executes code independently of the main CPU
- Dual-zone security module
- Endianness: Little endian
- Low device and system cost:
- Single 3.3-V supply
- No power sequencing requirement
- Integrated power-on reset and brownout reset
- Low power
- No analog support pins
- Clocking:
- Two internal zero-pin oscillators
- On-chip crystal oscillator and external clock input
- Watchdog timer module
- Missing clock detection circuitry
- Up to 42 individually programmable, multiplexed General-Purpose Input/Output (GPIO) pins with input filtering
- JTAG boundary scan support
- IEEE Standard 1149.1-1990 Standard Test Access Port and Boundary Scan Architecture
- Peripheral Interrupt Expansion (PIE) block that supports all peripheral interrupts
- Three 32-bit CPU timers
- Independent 16-bit timer in each ePWM module
- On-chip memory
- Flash, SARAM, Message RAM, OTP, CLA Data ROM, Boot ROM, Secure ROM available
- 128-bit security key and lock
- Protects secure memory blocks
- Prevents firmware reverse-engineering
- Serial port peripherals
- Three Serial Communications Interface (SCI) (Universal Asynchronous Receiver/Transmitter [UART]) modules
- One Serial Peripheral Interface (SPI) module
- One Inter-Integrated-Circuit (I2C) bus
- One Enhanced Controller Area Network (eCAN) bus
- Enhanced control peripherals
- Enhanced Pulse Width Modulator (ePWM)
- Enhanced Capture (eCAP) module
- Enhanced Quadrature Encoder Pulse (eQEP) module
- Analog peripherals
- One 12-bit Analog-to-Digital Converter (ADC)
- One on-chip temperature sensor for oscillator compensation
- Up to seven comparators with up to three integrated Digital-to-Analog Converters (DACs)
- One buffered reference DAC
- Up to four Programmable Gain Amplifiers (PGAs)
- Up to four digital filters
- Advanced debug features
- Analysis and breakpoint functions
- Real-time debug through hardware
- 80-pin PN Low-Profile Quad Flatpack (LQFP)
- Temperature options
- T: –40°C to 105°C
- S: –40°C to 125°C
- Q: –40°C to 125°C (AEC Q100 qualification for automotive applications)
C2000™ real-time control MCUs are optimized for processing, sensing, and actuation to improve closed-loop performance in real-time control applications such as industrial motor drives; solar inverters and digital power; electrical vehicles and transportation; motor control; and sensing and signal processing. The C2000 line includes the Premium performance MCUs and the Entry performance MCUs.
The F2805x family of microcontrollers (MCUs) provides the power of the C28x core and CLA coupled with highly integrated control peripherals in low pin-count devices. This family is code-compatible with previous C28x-based code, and also provides a high level of analog integration.
An internal voltage regulator allows for single-rail operation. Analog comparators with internal 6-bit references have been added and can be routed directly to control the PWM outputs. The ADC converts from 0 to 3.3-V fixed full-scale range and supports ratio-metric VREFHI/VREFLO references. The ADC interface has been optimized for low overhead and latency.
The Analog Front End (AFE) contains up to seven comparators with up to three integrated DACs, one VREFOUT-buffered DAC, up to four PGAs, and up to four digital filters. The PGAs can amplify the input signal in three discrete gain modes. The actual number of AFE peripherals will depend upon the TMS320F2805x device number. See Device Comparison for more details.
To learn more about the C2000 MCUs, visit the C2000™ real-time control MCUs page.
관심 가지실만한 유사 제품
비교 대상 장치와 유사한 기능.
기술 자료
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
XDS110ISO-EVM — C2000 및 Sitara™ controlSOM용 XDS110 절연 플러그인 평가 모듈
ALGO-3P-UISP1-TI — 텍사스 인스트루먼트 장치용 Algocraft μISP1 프로그래머
μISP는 호스트 PC(RS-232, USB, LAN 연결 기능이 내장되어 있음)에 연결되어 작동하거나 단독 모드로 작동할 수 있습니다.
독립 실행형 모드의 프로그래밍 싸이클은 단순히 START 버튼을 누르거나 일부 TTL 제어 라인을 통해 실행될 수 있습니다.
컴팩트한 크기와 다양한 기능을 갖추고 있어 생산 환경, 수동 및 자동 프로세스에 간편하게 통합할 수 있습니다.
TMDXCNCD28055ISO — Piccolo F2805x 절연 USB controlCARD
TMDXCNCD28055ISO는 Piccolo F2805x 시리즈를 위한 DIMM100 제어 카드 기반 평가 및 개발 도구입니다. controlCARD는 두 가지 표준 폼 팩터(100핀 DIMM 또는 180핀 HSEC) 중 하나를 활용하여 로우 프로파일 단일 보드 컨트롤러 솔루션을 제공하는 완전한 보드 레벨 모듈입니다.
첫 번째 평가를 위해 controlCARD는 일반적으로 도킹 스테이션 또는 애플리케이션 키트와 함께 번들로 구매합니다. TMDXCNCD28055ISO 제어 카드가 작동하려면 DIMM100 베이스보드가 필요합니다.
TMDSEMU200-U — XDS200 USB 디버그 프로브
XDS200은 TI 임베디드 장치를 디버깅하는 데 사용되는 디버그 프로브(에뮬레이터)입니다. 대부분의 장치의 경우 더욱 저렴한 신형 XDS110(www.ti.com/tool/TMDSEMU110-U)을 사용하실 것을 권장합니다. XDS200은 단일 포드에서 다양한 표준(IEEE1149.1, IEEE1149.7, SWD)을 지원합니다. 모든 XDS 디버그 프로브는 ETB(임베디드 트레이스 버퍼)가 포함되어 있는 모든 Arm® 및 DSP 프로세서에서 코어 및 시스템 트레이스를 지원합니다.
XDS200은 TI 20핀 커넥터(TI 14핀, (...)
TMDSEMU560V2STM-U — XDS560™ 소프트웨어 v2 시스템 추적 USB 디버그 프로브
XDS560v2는 디버그 프로브의 XDS560™ 제품군 중 최고의 성능을 가진 제품으로, 기존의 JTAG 표준(IEEE1149.1)과 cJTAG(IEEE1149.7)를 모두 지원합니다. SWD(직렬 와이어 디버그)는 지원하지 않습니다.
모든 XDS 디버그 프로브는 ETB(임베디드 추적 버퍼)가 있는 모든 ARM 및 DSP 프로세서에서 코어와 시스템 트레이스를 지원합니다. 핀을 통한 추적의 경우 XDS560v2 PRO TRACE가 필요합니다.
XDS560v2는 MIPI HSPT 60핀 커넥터(TI 14핀, TI 20핀 및 ARM (...)
TMDSEMU560V2STM-UE — XDS560v2 시스템 추적 USB 및 이더넷 디버그 프로브
The XDS560v2 is the highest performance of the XDS family of debug probes and supports both the traditional JTAG standard (IEEE1149.1) and cJTAG (IEEE1149.7). Note that it does not support serial wire debug (SWD).
All XDS debug probes support Core and System Trace in all ARM and DSP processors that (...)
ALGO-3P-WRITENOW — Algocraft WriteNow! 프로그래머
WriteNow! 시스템 내 프로그래머 시리즈는 프로그래밍 산업에서 획기적인 발전입니다. 프로그래머는 다양한 제조업체의 수많은 장치(마이크로컨트롤러, 메모리, CPLD 및 기타 프로그래머블 장치)를 지원하며 간편한 ATE/장치 통합을 위한 컴팩트한 크기를 가지고 있습니다. 이는 단독으로 작동하거나 호스트 PC(RS-232, LAN 및 USB 연결 기능이 내장되어 있음)에 연결되어 있으며 사용이 간편한 소프트웨어 유틸리티가 제공됩니다.
C2000WARE — C2000Ware for C2000 Microcontrollers
C2000Ware는 개발 시간을 최소화하기 위해 만들어진 포괄적인 소프트웨어 및 문서 세트입니다. 여기에는 장치별 드라이버, 라이브러리 및 주변 기기 예제가 포함되어 있습니다.
- C2000 controlCARD, 실험용 키트 및 LaunchpPad용 하드웨어 설계 회로도, BOM, Gerber 파일 및 문서.
- 장치별 지원 파일, 비트 필드 헤더, 비트 필드 장치 주변 기기 예제(LaunchPad ™ 데모 포함) 및 장치 개발 사용 설명서.
- 장치별 드라이버 라이브러리 및 드라이버 기반 주변 기기 예제.
- FreeRTOS 커널, C28x 및 (...)
C2000_CLA_SAFETI_CQKIT_RV — C2000™ and CLA safety compiler qualification kit (leverages compiler release validations)
안전 컴파일러 검증 키트는 IEC 61508 및 ISO 26262 등 기능 안전 표준에 대한 TI ARM, C6000, C7000 또는 C2000/CLA C/C++ 컴파일러 사용 검증 시 고객을 지원하기 위해 개발되었습니다.
안전 컴파일러 검증 키트:
- TI 고객에게 무료로 제공됩니다
- 사용자가 검증 테스트를 실행할 필요가 없음
- 컴파일러 범위 분석 지원*
- * 범위 데이터 수집에 대한 지침은 각 QKIT 다운로드 페이지에서 다운로드할 수 있습니다.
- Validas 컨설팅은 포함되지 않음
안전 컴파일러 검증 키트에 액세스하려면 위의 요청 버튼 (...)
CCSTUDIO — Code Composer Studio integrated development environment (IDE)
CCStudio™ IDE is part of TI's extensive CCStudio™ development ecosystem and is an integrated development environment for TI's microcontrollers, processors, wireless connectivity devices, and radar sensors. CCStudio IDE is available as desktop or cloud-based applications. The cloud version (...)
TI-DEVELOPER-ZONE — Start embedded development on your desktop or in the cloud
WHIS-3P-SAFERTOS — WITTENSTEIN SAFERTOS 사전 인증 안전 RTOS
SAFERTOS®는 임베디드 프로세서를 위해 설계된 고유한 실시간 운영 체제입니다. TÜV SÜD의 IEC 61508 SIL3 및 ISO 26262 ASILD 표준에 따라 사전 인증을 받았습니다. SAFERTOS®는 WHIS 전문가 팀에서 안전을 위해 특별히 제작되었으며, 전 세계적으로 안전이 중요한 응용 분야에 사용됩니다. WHIS와 텍사스 인스트루먼트는 10년 넘게 협력해 왔습니다. 이 기간 동안, WHIS는 SAFERTOS®를 광범위한 TI 프로세서로 이식하여 널리 사용되는 모든 코어를 지원하며 요청 시 추가 아키텍처를 (...)
INSTASPIN-BLDC — InstaSPIN™-BLDC 솔루션
In keeping with TI’s philosophy of making motor control more accessible and easier to use by design engineers, TI is proud to announce the release of its newest motor control technology, InstaSPIN-BLDC. Targeted at low cost BLDC applications, InstaSPIN-BLDC is a sensorless control technique based (...)
C2000-DIGITAL-CONTROL-LIBRARY — C2000 디지털 제어 라이브러리
CONTROLSUITE — controlSUITE™ 소프트웨어 제품군 C2000 ™ 마이크로컨트롤러용 소프트웨어 및 개발 툴
C2000™ 마이크로컨트롤러용 controlSUITE™는 시스템 개발 시간을 최소화하도록 설계된 포괄적인 소프트웨어 인프라, 툴 및 문서 세트입니다. 장치별 드라이버와 지원 소프트웨어에서 정교한 시스템 애플리케이션의 완전한 예제에 이르기까지 controlSUITE™는 개발 및 평가의 모든 단계에서 필요한 리소스를 제공합니다.
이제 디지털 전원 설계자를 위한 powerSUITE와 산업용 드라이브 설계자를 위한 DesignDRIVE가 포함됩니다.
참고: 새로운 Piccolo F28004x 시리즈에 대한 소프트웨어 지원은 C2000Ware (...)
IEC60730SWPACKAGES — C2000 SafeTI™ 60730 SW 패키지
C2000 MCU SafeTI-60730 소프트웨어 패키지에는 UL 인증을 받은 구성 요소인 SafeTI™ 소프트웨어 패키지가 포함되어 있어 C2000™ 실시간 제어 MCU(마이크로컨트롤러)를 사용하여 기능 안전 컨수머 애플리케이션을 보다 쉽고 빠르게 설계할 수 있습니다. 이러한 SafeTI 소프트웨어 패키지의 소프트웨어는 UL 인증을 받은 구성 요소로, 가전제품, 아크 감지기, 전원 컨버터, 전원 툴, 전기 자전거 등을 포함한 IUL 1998:2008 Class 1 표준 및 IEC 60730-1:2010 Class B를 (...)
UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors
UniFlash는 TI의 광범위한 CCStudio™ 개발 에코시스템의 일부로, TI 마이크로컨트롤러 및 무선 연결 장치의 온칩 플래시와 TI 프로세서의 온보드 플래시를 프로그래밍하기 위한 소프트웨어 도구입니다. UniFlash는 그래픽 및 명령줄 인터페이스를 모두 제공하며, 데스크톱 또는 클라우드 환경에서 실행할 수 있습니다.
UniFlash는 CCStudio™ 개발자 영역의 클라우드에서 실행하거나 Windows®, Linux®, macOS® 컴퓨터에서 다운로드해 사용할 수 있습니다.
macOS는 mmWave, AMx, K2G 및 (...)
C2000-3P-SEARCH — C2000 타사 검색 툴
TI has partnered with multiple companies to offer a wide range of solutions and services for TI C2000 devices. These companies can accelerate your path to production using C2000 devices. Download this search tool to quickly browse third-party details and find the right third-party to meet your (...)
TIDM-1AXISMTR-PFC-5X — 통합 전력 역률 보정을 사용한 단일 축 모터 제어 레퍼런스 디자인
이레퍼런스 설계는 단일 축 모터 제어 및 전력 역률 보정(PFC)을 단일 마이크로컨트롤러에 통합하기 위한 모범 사례를 보여줍니다. 이 관행은 가변 주파수 압축기, 특히 HVAC 시스템 설계 시 널리 사용됩니다. 이 구현은 무센서 FOC(자속 기준 제어) 알고리즘을 사용하여 TMS320F2805x 마이크로컨트롤러에서 PMSM(영구 자석 동기 모터)와 2상 인터리브 PFC를 구동하도록 최적화되어 있습니다. FOC 알고리즘은 광범위한 속도에서 효율성을 유지하며, 모터의 동적 모델을 처리하여 과도 상에 따른 토크 변화를 고려합니다.
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| LQFP (PN) | 80 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.