이 제품의 최신 버전이 있습니다
다른 핀 출력을 지원하지만 비교 대상 장치와 동일한 기능.
TPS7B7702-Q1
- Qualified for Automotive Applications
- AEC-Q100 Qualified With
the Following Results:
- Device Temperature Grade 1: –40°C to 125°C Ambient Operating Temperature Range
- Device HBM ESD Classification 2
- Device CDM ESD Classification C4B
- Single and Dual-Channel LDO With Current Sense and Adjustable Current-Limit
- 4.5-V to 40-V Wide Input Voltage Range, 45-V Load Dump
- Power Switch Mode When Tying FB to GND
- 1.5-V to 20-V Adjustable Output Voltage
- Up to 300-mA Output Current per Channel
- Adjustable Current-Limit With External Resistor
- High Accuracy Current-Sense to Detect Antenna Open Condition at Low Current Without Further Calibration
- High Power-Supply Rejection Ratio: Typical 73 dB at 100 Hz
- Integrated Reverse-Polarity Protection, Down to –40 V and No Need for External Diode
- 500-mV Max Dropout Voltage at 100-mA Load
- Stable With Output Capacitor in 2.2-µF to 100-µF Range (ESR 1 mΩ to 5 Ω)
- Integrated Protection and Diagnostics
- Thermal Shutdown
- Undervoltage Lockout (UVLO)
- Short-Circuit Protection
- Reverse Battery Polarity Protection
- Reverse-Current Protection
- Output Short-to-Battery Protection
- Output Inductive Load Clamp
- Multiplexing Current Sense Between Channels and Devices
- Ability to Distinguish All Faults With Current Sense
- 16-Pin HTSSOP PowerPAD™ Package
The TPS7B770x-Q1 family of devices feature a single and dual, high-voltage low-dropout regulator (LDO) with current sensing, designed to operate with a wide input-voltage range from 4.5 V to 40 V (45-V load dump protection). These devices provide power to the low-noise amplifiers of the active antenna through a coax cable with 300 mA per channel current. Each channel also provides an adjustable output voltage from 1.5 V to 20 V.
These devices provide diagnostics through the current sense and error pins. To monitor the load current, a high-side current-sense circuitry provides a proportional analog output to the sensed load current. The accurate current sense allows detection of open, normal, and short-circuit conditions without the need for further calibration. Current sense can be multiplexed between channels and devices to save analog-to-digital converter (ADC) resources. Each channel also implements adjustable current limit with an external resistor.
An integrated reverse polarity diode eliminates the need for an external diode. These devices feature standard thermal shutdown, short-to-battery protection on the output, and reverse current protection. Each channel has internal inductive clamp protection on the output during inductive switch off.
These devices operate over a –40°C to +125°C ambient temperature range.
관심 가지실만한 유사 제품
비교 대상 장치와 유사한 기능.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | TPS7B770x-Q1, Automotive, Single- and Dual-Channel Antenna LDO With Current Sense datasheet (Rev. C) | PDF | HTML | 2018. 9. 12 | |
| 애플리케이션 노트 | TPS7B7702-Q1 Reverse Current Protection | PDF | HTML | 2026. 7. 1 | ||
| 백서 | Reduce System Noise Using Parallel LDOs | PDF | HTML | 2025. 11. 3 | ||
| 기능 안전 정보 | TPS7B770x-Q1 Functional Safety FIT Rate, FMD, and Pin FMA (Rev. A) | PDF | HTML | 2024. 8. 2 | ||
| 백서 | Parallel LDO Architecture Design Using Ballast Resistors | PDF | HTML | 2022. 12. 14 | ||
| 백서 | Comprehensive Analysis and Universal Equations for Parallel LDO's Using Ballast | PDF | HTML | 2022. 12. 13 | ||
| 애플리케이션 노트 | TPS7B7702-Q1 Short Circuit Test Report | 2020. 2. 28 | |||
| 기술 문서 | LDO Basics: Preventing reverse current | PDF | HTML | 2018. 7. 25 | ||
| 추가 자료 | Fundamentals of designing with LDOs in auto battery direct connect applications | 2017. 2. 27 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
BOOSTXL-CANFD-LIN — SPI-CAN FD SBC + LIN 트랜시버 BoosterPack™ 플러그인 모듈
TPS7B7702EVM — TPS7B7702-Q1 듀얼 채널 안테나 LDO 선형 레귤레이터 평가 모듈
The TPS7B7702EVM evaluation module (EVM) helps designers evaluate the operation and performance of TPS7B7702QPWPRQ1 antenna LDO. The TPS7B7702-Q1 is a monolithic integrated dual channel LDO with current sense in an HTSSOP package. The device is designed to provide a power (...)
PARALLEL-LDO-CALC — Parallel low-dropout (LDO) calculator
병렬 저손실(LDO) 계산기는 밸러스트 저항을 사용하여 병렬 LDO 레귤레이터에 대한 최악의 분석을 제공하는 Microsoft® Excel® 기반 툴입니다. 이 툴은 사용자가 시스템 요구 사항 세트에 필요한 병렬 LDO 레귤레이터의 최소 수와 최적의 밸러스트 저항을 식별하는 데 도움이 됩니다.
병렬 애플리케이션에 사용되는 일반적인 LDO 레귤레이터에 대한 데이터 시트 정보는 계산기에 미리 채워져 있습니다. 사용자는 시스템 요구 사항을 기반으로 시스템 요구 사항에 가장 잘 맞는 LDO 레귤레이터 디바이스를 평가할 수 있습니다.
TIDA-01005 — MIPI CSI-2 출력을 지원하는 4카메라 허브용 차량용 ADAS 레퍼런스 디자인
TIDA-01569 — 디지털 진단 및 통합 보호를 지원하는 4채널 안테나 LDO 레퍼런스 설계
TIDA-050096 — 확장 가능한 고전류 병렬 차량용 레퍼런스 설계
이 레퍼런스 설계는 TPS7B7702-Q1 선형 레귤레이터를 병렬로 연결하여 팬텀 전원 공급 장치와 같은 일반적인 애플리케이션에서 필요할 수 있는 더 높은 부하 전류를 달성하는 두 가지 방법을 보여줍니다. 첫 번째 접근 방식은 외부 연산 증폭기(OP 앰프)를 사용하여 4개의 TPS7B7702-Q1 채널을 병렬로 연결함으로써 부하에 최대 1.2A를 공급합니다. 이 기법은 확장 가능하며 추가 전류를 위해 더 많은 선형 레귤레이터 채널을 병렬로 연결할 수 있습니다. 두 번째 접근 방식은 밸러스트 저항을 사용하여 2개의 (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| HTSSOP (PWP) | 16 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.