TRF4140-Q1
- Benefits
- Full Embedded Sequence Timing Controller Removes All Timing Constraints From the Host Controller
- Automatic Sequence Repetition for Easy Implementation of Energy-Efficient Polling Systems
- Separate Transmit and Receive Buffers Reduce Host Controller Performance Requirements
- Embedded Sequence-Auto-Repeat Enables Low-Power Polling System Without Host Controller Interaction
- Embedded Half-Duplex (HDX) Protocol Support Enables Flexible and Scalable System Implementation
- Sine-Wave Controlled Transmitter Stages Enable High-Power Remote Antenna Systems With Cable Lengths of Several Meters and Superior EMC Performance
- Sequence Preloading With Event-Triggered Execution for Fastest System Reaction Time
- Features
- Integrated Boost Controller for Wide Supply Voltage Range With Jump Start and Load Dump Protection
- Antenna Driver With up to 20-V Peak-to-Peak Output Voltage Amplitude and up to 1-A Peak Antenna Current With Sine-Wave or Square-Wave Output
- Flexible Host Control Interface
- 4-Wire SPI
- Configurable I/O Functions to Extend Controller Interface Such as an Interrupt Request Signal
- Interface Voltage Supply Range From 2.5 V to 5.5 V
- Ultra-Low Current Consumption in Sleep State
- Fractional Synthesizer With 10-kHz to 500‑kHz Frequency Range With 60-Hz Step Size
- PSK and ASK Transmitter Stage
- FSK Receiver and Demodulator
- Four Programmable Half-Bridge MOSFET Antenna Drivers
- Pairs of Half-Bridge Antenna Drivers can be Used Together as a Full-Bridge Driver to Double the Possible Output Voltage Amplitude
- Antenna Current Measurement With 5-Bit Resolution for High Side and Low Side of Antenna Driver Stages
- Programmable Antenna Driver Output Voltage in Sine-Wave Mode
- Supply-Controlled Antenna Driver Voltage in Square-Wave Mode
- Output Stage is Overload Protected for Over-Current and Over-Temperature Conditions
- Antenna Driver Diagnostics: Short to Ground, Short to Antenna Driver Supply Voltage, and Open-Load Detection
- Supports On-Off Keying With Data Rates up to 70 kbps for Downlink and Uplink
The TRF4140-Q1 low-frequency (LF) transceiver base station device is intended for immobilizer and PEPS systems to communicate with LF transponders, remote keyless entry, and passive entry devices. The antenna driver stage consists of four MOSFET antenna drivers to send modulated LF transmissions and a receiver for detection and demodulation of LF transponder responses. The HDX communication scheme uses frequency shift keying (FSK) as the uplink modulation. The device can drive LF antennas to provide a wake-up and data sequence (PEPS), and it can also receive transponder responses on any or all channels (immobilizer).
The TRF4140-Q1 device needs VDD supply (5 V) for its control blocks and to feed the integrated logic voltage regulator. The antenna driver is supplied separately by VDDH (4 V to 20 V). This voltage can be used to generate a sine-wave output signal for superior EMC performance, which is important for remote antenna applications with several meters of antenna cable.
The TRF4140-Q1 device manages all timings required for a communication sequence without the need for an accurate host controller interaction. In conjunction with transmit and receive FIFOs, the host controller is off-loaded from all timing-critical events, which enables easy host controller process scheduling. In particular, the host controller start-up process for an automotive body control module is tremendously relaxed by this base station device.
The TRF4140-Q1 device supports sequence preloading and sequence execution on external events to start the immobilization process exactly when the key fob is detected. So, delays due to configuration can be avoided in inconvenient time frames.
자세한 정보
전체 데이터시트, 정오표 및 추가 지원을 요청하십시오. 승인된 사용자는 1-2일 이내에 이메일을 받게 됩니다.
기술 문서
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | TRF4140-Q1 Abstract Low-Frequency Transceiver for Immobilizer, Passive Start, Passive Entry datasheet (Rev. B) | PDF | HTML | 2018/10/31 |
| Product overview | Car access product family (Rev. A) | 2013/09/10 | ||
| Product overview | Car access product family | 2012/02/21 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
| 패키지 | 핀 | 다운로드 |
|---|---|---|
| HTQFP (PHN) | 48 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.