AFE4410
- Accurate, Continuous Heart-Rate Monitoring:
- Up to 100-dB Dynamic Range for Accurate Heart-Rate Detection
- Low Current for Continuous Operation on a Wearable Device With a Typical Value:
- 30 µA for an LED, 25 µA for the Receiver
- Transmitter:
- 4 LEDs in Common Anode Configurations
- 8-Bit Programmable LED Current to 200 mA
- Mode to Fire Two LEDs in Parallel
- Programmable LED On-Time
- Simultaneous Support of 3 LEDs for Optimized SpO2, HRM, or Multiwavelength HRM
- Average Current of 30 µA Adequate for a Typical Heart-Rate Monitoring Scenario:
- 20-mA Setting, 60-µs Pulse Duration,
25-Hz Sampling Rate
- 20-mA Setting, 60-µs Pulse Duration,
- Receiver:
- Supports 3 Time-Multiplexed PD Inputs
- 24-Bit Representation of Current Input From PD in Two’s-Complement Format
- Individual DC Offset Subtraction DAC
(Up to ±127-µA Range) at TIA Input for Each LED, Ambient - Digital Ambient Subtraction at ADC Output
- Transimpedance Gain: 10 kΩ to 2 MΩ
- Noise Filtering With Programmable Bandwidth
- Receiver Operates at Approximately 1-µA/Hz Sampling Rate (Example, 25 µA at 25 Hz)
- Hardware Power-Down Mode: Approximately 0-µA Current
- Flexible Pulse Sequencing and Timing Control
- Clocking Via External Clock or Internal Oscillator
- FIFO With 128-Sample Depth:
- Programmable Partitioning Across Phases
- Pin-Selectable I2C, SPI Interface
- Operating Temperature Range: –20°C to +70°C
- 2.6-mm × 2.1-mm, 0.4-mm Pitch DSBGA Package
- Supplies:
- Tx: 3 V to 5.25 V
- Rx: 1.8 V to 1.9 V (LDO Bypass),
2.0 V to 3.6 V (LDO Enabled) - IO: 1.7 V to Rx_SUP
TheAFE4410is an analog front-end for optical biosensing applications, such as heart rate monitoring (HRM). The device supports a maximum of four switching light-emitting diodes (LEDs) and a maximum of three photodiodes (PDs). The electrical current from the photodiode is converted into voltage by the transimpedance amplifier (TIA) and digitized using an analog-to-digital converter (ADC). The ADC code is stored in a 128-sample first-in, first-out block (FIFO) with programmable depth. The FIFO can be read out using either an I2C interface or a serial peripheral interface (SPI). The AFE also has a fully integrated LED driver with 8-bit current control. The device has high dynamic range transmit-and-receive circuitry offering a dynamic range of up to 100 dB that enables accurate heart ratesensing. The AFE achieves extremely low current levels by operating an ultralow power (ULP) mode set by using the ENABLE_ULP register bit.
更多資訊
在 NDA 下提供完整的產品規格表和其他設計資源。立即索取
您可能會感興趣的類似產品
技術文件
| 類型 | 標題 | 日期 | ||
|---|---|---|---|---|
| * | Data sheet | AFE4410 Ultra-Small, Integrated AFE With FIFO for Wearable, Continuous Optical Heart-Rate Monitoring and Biosensing datasheet (Rev. B) | PDF | HTML | 2019年 7月 31日 |
| Technical article | Optical heart-rate sensors for biometric wearables | PDF | HTML | 2018年 5月 3日 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
AFE4403EVM — 適用於心率監控器和脈搏血氧儀的 AFE4403 整合式 AFE 評估模組
The AFE4403EVM is intended for evaluating the AFE4403 device. The fully integrated AFE is ideally suited for Pulse Oximeter and Heart rate monitoring applications and consists of low noise receive channel, the LED transmit section and diagnostics for sensor and LED fault detection. The AFE4403 has (...)
AFE4410EVM — 具有 FIFO 且適用於穿戴式光學心率監測的 AFE4410 整合式 AFE 評估模組
AFE4410 為光學生物感測應用領域的類比前端 (AFE)，如心率監控 (HRM) 與周邊微血管含氧飽和度 (SpO2)。裝置支援多達四個切換發光二極體 (LED) 和三個光二極體。光二極體電流透過轉阻放大器 (TIA) 轉換為電壓，並使用類比轉數位轉換器 (ADC) 進行數位化。ADC 程式碼可以儲存在具有可編程深度的 128 取樣 FIFO 中。可以對 FIFO 深度進行分區以適應需要儲存的相位。FIFO 可使用 I2C 或 SPI 介面讀出。AFE 也配備具有 8 位元電流控制功能的完整整合 LED 驅動器。裝置可由外部時脈或內部振盪器計時。裝置利用 I2C (...)
AFE4490SPO2EVM — 適用於脈搏血氧儀的 AFE4490 整合式類比前端 (AFE) 評估模組
The AFE44x0SPO2EVM is intended for evaluating AFE4400 and AFE4490 devices. The family of devices are fully integrated AFE ideally suited for Pulse Oximeter applications and consist of low noise receive channel, the LED transmit section and diagnostics for sensor and LED fault detection. The (...)
PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| DSBGA (YZ) | 30 | Ultra Librarian |
訂購與品質
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中持續性的可靠性監測
- 晶圓廠位置
- 組裝地點
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。