SNVSAU8A June   2017  – February 2024 TPS549B22

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 25-A FET
      2. 6.3.2 On-Resistance
      3. 6.3.3 Package Size, Efficiency and Thermal Performance
      4. 6.3.4 Soft-Start Operation
      5. 6.3.5 VDD Supply Undervoltage Lockout (UVLO) Protection
      6. 6.3.6 EN_UVLO Pin Functionality
      7. 6.3.7 Fault Protections
        1. 6.3.7.1 Current Limit (ILIM) Functionality
        2. 6.3.7.2 VDD Undervoltage Lockout (UVLO)
        3. 6.3.7.3 Overvoltage Protection (OVP) and Undervoltage Protection (UVP)
        4. 6.3.7.4 Out-of-Bounds Operation
        5. 6.3.7.5 Overtemperature Protection
    4. 6.4 Device Functional Modes
      1. 6.4.1 D-CAP3™ Control Mode Topology
      2. 6.4.2 DCAP Control Topology
    5. 6.5 Programming
      1. 6.5.1 Programmable Pin-Strap Settings
        1. 6.5.1.1 Address Selection (ADDR) Pin
        2. 6.5.1.2 VSEL Pin
        3. 6.5.1.3 D-CAP3™ Control Mode Selection
        4. 6.5.1.4 Application Workaround to Support 4-ms and 8-ms SS Settings
      2. 6.5.2 Programmable Analog Configurations
        1. 6.5.2.1 RSP/RSN Remote Sensing Functionality
          1. 6.5.2.1.1 Output Differential Remote Sensing Amplifier
        2. 6.5.2.2 Power Good (PGOOD Pin) Functionality
      3. 6.5.3 PMBus Programming
        1. 6.5.3.1 TPS549B22 Limitations to the PMBUS Specifications
        2. 6.5.3.2 Target Address Assignment
        3. 6.5.3.3 PMBUS Address Selection
        4. 6.5.3.4 Supported Formats
          1. 6.5.3.4.1 Direct Format — Write
          2. 6.5.3.4.2 Combined Format — Read
        5. 6.5.3.5 Stop Separated Reads
        6. 6.5.3.6 Supported PMBUS Commands and Registers
  8. 7 Register Maps
    1. 7.1  OPERATION Register (address = 1h)
    2. 7.2  ON_OFF_CONFIG Register (address = 2h)
    3. 7.3  CLEAR FAULTS (address = 3h)
    4. 7.4  WRITE PROTECT (address = 10h)
    5. 7.5  STORE_DEFAULT_ALL (address = 11h)
    6. 7.6  RESTORE_DEFAULT_ALL (address = 12h)
    7. 7.7  CAPABILITY (address = 19h)
    8. 7.8  VOUT_MODE (address = 20h)
    9. 7.9  VOUT_COMMAND (address = 21h)
    10. 7.10 VOUT_MARGIN_HIGH (address = 25h) ®
    11. 7.11 VOUT_MARGIN_LOW (address = 26h)
    12. 7.12 STATUS_BYTE (address = 78h)
    13. 7.13 STATUS_WORD (High Byte) (address = 79h)
    14. 7.14 STATUS_VOUT (address = 7Ah)
    15. 7.15 STATUS_IOUT (address = 7Bh)
    16. 7.16 STATUS_CML (address = 7Eh)
    17. 7.17 MFR_SPECIFIC_00 (address = D0h)
    18. 7.18 MFR_SPECIFIC_01 (address = D1h)
    19. 7.19 MFR_SPECIFIC_02 (address = D2h)
    20. 7.20 MFR_SPECIFIC_03 (address = D3h)
    21. 7.21 MFR_SPECIFIC_04 (address = D4h)
    22. 7.22 MFR_SPECIFIC_06 (address = D6h)
    23. 7.23 MFR_SPECIFIC_07 (address = D7h)
    24. 7.24 MFR_SPECIFIC_44 (address = FCh)
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 TPS549B22 1.5-V to 18-V Input, 1-V Output, 25-A Converter
      2. 8.2.2 Design Requirements
      3. 8.2.3 Detailed Design Procedure
        1. 8.2.3.1  Custom Design With WEBENCH® Tools
        2. 8.2.3.2  Switching Frequency Selection
        3. 8.2.3.3  Inductor Selection
        4. 8.2.3.4  Output Capacitor Selection
          1. 8.2.3.4.1 Minimum Output Capacitance to Make Sure of Stability
          2. 8.2.3.4.2 Response to a Load Transient
          3. 8.2.3.4.3 Output Voltage Ripple
        5. 8.2.3.5  Input Capacitor Selection
        6. 8.2.3.6  Bootstrap Capacitor Selection
        7. 8.2.3.7  BP Pin
        8. 8.2.3.8  R-C Snubber and VIN Pin High-Frequency Bypass
        9. 8.2.3.9  Optimize Reference Voltage (VSEL)
        10. 8.2.3.10 MODE Pin Selection
        11. 8.2.3.11 ADDR Pin Selection
        12. 8.2.3.12 Overcurrent Limit Design
      4. 8.2.4 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Examples
      3. 8.4.3 Mounting and Thermal Profile Recommendation
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Development Support
        1. 9.1.1.1 Custom Design With WEBENCH® Tools
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 Receiving Notification of Documentation Updates
    4. 9.4 Support Resources
    5. 9.5 Trademarks
    6. 9.6 Electrostatic Discharge Caution
    7. 9.7 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • RVF|40
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.19 MFR_SPECIFIC_02 (address = D2h)

The MFR_SPECIFIC_02 register allows the user to read the configuration of various pin-strap features and/or overwrite them. Note that any overwritten values here are only good until the next power-on-reset, when all parameters revert back to their pin-strap configurations.

Figure 7-16 MFR_SPECIFIC_02
76543210
TRKSEQ0FORCESKIPSSSSTHICLOFFCM
R/WR/WRR/WR/WR/WR/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 7-18 MFR_SPECIFIC_02
BitFieldTypeResetDescription
7TRKR/WP

This bit indicates whether the device is using internal or external reference voltage tracking. It will initially be loaded and reflect the value of the pin strap; but, can also be overwritten by PMBus.
0: No tracking. The device will use internal reference voltage.


1: External tracking.
6SEQR/WP

This bit indicates whether the device is using internal or external soft-start ramp. It will initially be loaded and reflect the value of the pin strap; but, can also be overwritten by PMBus.
0: No sequencing. The device will use the internal soft start ramp.


1: Sequencing
5R0
4FORCESKIPSSR/W1

This bit (when set) allows the user to force Soft-start to always use SKIP mode; regardless of the CM pin strap.
0: CM bit controls whether to operate in SKIP or FCCM mode during and after soft start.


1: Soft start is forced to operate in SKIP mode, then CM bit controls the mode after soft start.
3:2SSTR/WPThese bits indicate the time the device takes to ramp the output voltage up to regulation (that is, soft-start). The field will initially be loaded and reflect the value of the pin strap; but, can also be overwritten by PMBus. (Refer to Table 7-19)
1HICLOFFR/WP

This bit indicates the response the device will take upon an output undervoltage fault. There are two fault response options which are enforced by the analog circuits: Hiccup or Latch-off. The bit value will initially be loaded and reflect the value of the pin strap; but, can also be overwritten by PMBus.
0: Hiccup after UVP fault.


1: Latch off after UVP fault.
0CMR/WP

This bit indicates the conduction mode for the device. The bit value will initially be loaded and reflect the value of the pin strap; but, can also be overwritten by PMBus.
0: SKIP


1: FCCM
Table 7-19 SST
SST[1] SST[0] Soft-start time
0 0 1 ms
0 1 2 ms
1 0 4 ms
1 1 8 ms