SBASB22 December   2025 ADS9324

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Switching Characteristics
    8. 5.8 Timing Diagrams
  7. 6 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Analog Inputs
      2. 7.3.2  Input Clamp Protection Circuit
      3. 7.3.3  Analog Input Impedance
      4. 7.3.4  Programmable Gain Amplifier (PGA)
      5. 7.3.5  ADC Transfer Function
      6. 7.3.6  Reference
      7. 7.3.7  Open Wire Safe Mode
      8. 7.3.8  System Offset Calibration
      9. 7.3.9  System Gain Calibration
      10. 7.3.10 ADC Gain and Offset Error Calibration
      11. 7.3.11 Digital Filter
        1. 7.3.11.1 System Phase Calibration
        2. 7.3.11.2 Block Average Filter
        3. 7.3.11.3 Moving Average Filter
        4. 7.3.11.4 Low-Pass FIR Filter
      12. 7.3.12 Digital Window Comparator
      13. 7.3.13 Alarm Modes
      14. 7.3.14 Data Interface
        1. 7.3.14.1 ADC Channel Modes
        2. 7.3.14.2 Daisy Chain
        3. 7.3.14.3 Diagnostic Flags
        4. 7.3.14.4 ADC Output Data Randomizer
        5. 7.3.14.5 Test Patterns for Data Interface
        6. 7.3.14.6 Digital Output Drive Strength Control
        7. 7.3.14.7 Digital Output Delay Adjustment
    4. 7.4 Device Functional Modes
      1. 7.4.1 Reset
      2. 7.4.2 Normal Operation
      3. 7.4.3 Standby Mode
    5. 7.5 Programming
      1. 7.5.1 Register Write Operation
      2. 7.5.2 Register Read Operation
      3. 7.5.3 Initialization Example - Single Lane Mode on SDOUT
  9. 8 Register Maps
    1. 8.1 ADS93xx Common Registers
    2. 8.2 AIN1 - AIN8 Channel Registers
    3. 8.3 AIN9 - AIN16 Channel Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 16-Channel, Data Acquisition System (DAQ) for Power Automation
        1. 9.2.1.1 Application Curve
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
        1. 9.4.1.1 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Mechanical Data

5.8 Timing Diagrams


ADS9324 Timing for Register Read and Write Operations

Figure 5-1 Timing for Register Read and Write Operations
ADS9324 ADC Conversion Data Read Timing: 8-Lane (Default Operation) Figure 5-2 ADC Conversion Data Read Timing: 8-Lane (Default Operation)

ADS9324 ADC Conversion Data Read Timing: 4-Lane

Figure 5-3 ADC Conversion Data Read Timing: 4-Lane

ADS9324 ADC Conversion Data Read Timing: 2-Lane

Figure 5-4 ADC Conversion Data Read Timing: 2-Lane

ADS9324 ADC Conversion Data Read Timing: 1-Lane

Figure 5-5 ADC Conversion Data Read Timing: 1-Lane

ADS9324 CONVST and DRDY, External Clock Oversampling

Note:
  1. Applicable when using block average filter with external clock oversampling mode and FIR filters. For FIR filters, N is the decimation factor.
Figure 5-6 CONVST and DRDY, External Clock Oversampling

ADS9324 CONVST and DRDY, Internal Clock Oversampling

Note:
  1. In the internal clock oversampling mode, CONVST must go high before the rising edge of the DRDY for proper device operation. The timing requirement is defined by tsu_CV_hi_DRDY_hi. This limits the minimum tPH_CV of the CONVST signal. The minimum value of tPH_CV is given by t PH_CV   = t CONVST   —  1.2  µs , applicable for f CONVST   ≤ 800kHz N , where N is the oversampling ratio.
  2. Applicable for block average filter with internal clock oversampling mode.
Figure 5-7 CONVST and DRDY, Internal Clock Oversampling