SLYW038D September   2014  – April 2025 AFE030 , AFE031 , AFE032 , ALM2402-Q1 , LMC6035-Q1 , LMV601 , LMV602 , LMV604 , LMV611 , LMV612 , LMV614 , LMV881 , OPA1602 , OPA1604 , OPA1612 , OPA1612-Q1 , OPA1622 , OPA1652 , OPA1654 , OPA1662 , OPA1662-Q1 , OPA1664 , OPA1688 , OPA170 , OPA170-EP , OPA171-Q1 , OPA172 , OPA180 , OPA188 , OPA191 , OPA192 , OPA197 , OPA211-EP , OPA2170 , OPA2171 , OPA2171-EP , OPA2171-Q1 , OPA2172 , OPA2180 , OPA2188 , OPA2192 , OPA2211-EP , OPA2211-HT , OPA2227-EP , OPA2277-EP , OPA2313 , OPA2314 , OPA2314-EP , OPA2314-Q1 , OPA2316 , OPA2317 , OPA2320-Q1 , OPA2322-Q1 , OPA2376-Q1 , OPA2625 , OPA313 , OPA314 , OPA316 , OPA317 , OPA320 , OPA322 , OPA348-Q1 , OPA355-Q1 , OPA4170 , OPA4171 , OPA4171-Q1 , OPA4172 , OPA4180 , OPA4188 , OPA4192 , OPA4277-EP , OPA4313 , OPA4314 , OPA4316 , OPA4317 , OPA4322 , OPA4322-Q1 , OPA549-HIREL , OPA564-Q1 , OPA625 , SM73307 , SM73308 , TLC2274-HT , TLE2141-Q1 , TLV2314 , TLV2316 , TLV2333 , TLV27L2-Q1 , TLV314 , TLV316 , TLV333 , TLV4314 , TLV4316 , TLV4333

1.   1
2.   Analog Engineer's Pocket Reference
3.   Conversions
   1.     Standard decimal prefixes
   2.     Metric conversions
   3.     Temperature scale conversions
   4.     Error conversions ppm and percentage
   5.     Notes
4.   Discrete Components
   1.     Resistor color code
   2.     Capacitor specifications
   3.     Capacitance type overview
   4.     Diodes and LEDs
   5.     Bipolar junction transistors (BJT)
   6.     Junction field effect transistors (JFET)
   7.     Metal oxide semiconductor field effect transistor (MOSFET)
   8.     Notes
5.   Analog
   1.     Resistor equations
   2.     Power equations
   3.     Capacitor equations
   4.     Inductor equations
   5.     RMS and mean voltage
   6.     Logarithmic mathematical definitions
      1.      Alternative notations
   7.     dB definitions
      1.      Bode plot basics
      2.      Definitions
      3.      Log scale
      4.      Time to phase shift
      5.      Bode plots: Poles
   8.     Pole (equations)
      1.      Bode plots (zeros)
      2.      Zero (equations)
   9.     Notes
6.   Amplifier
   1.     Basic op amp configurations
      1.      Simple non-inverting amp with Cf filter
      2.      Simple inverting amp with Cf filter
      3.      Differential filter cutoff
      4.      Calculating amplifier offset voltage
   2.     Op amp bandwidth
      1.      Small signal step response
   3.     Full power bandwidth
   4.     Large signal response (slew rate)
   5.     Settling Time
   6.     Combining noise sources
      1.      Averaging noise sources
      2.      Noise bandwidth calculation
         1.       Broadband total noise calculation
      3.      1/f total noise calculation
      4.      Thermal noise calculation
      5.      Op amp noise model
      6.      Total noise calculations
   7.     AC response versus frequency (dominant 2-pole system)
      1.      Phase margin versus AC peaking
      2.      Transient overshoot (dominant 2-pole system)
      3.      Phase margin versus percentage overshoot
   8.     Stability open loop SPICE analysis
      1.      Stability transient square wave lab test
      2.      Stability AC sine wave lab test
   9.     Power dissipation calculation
   10.     Electrical overstress (EOS) protection
   11.     Notes
7.   PCB and Wire
   1.     PCB and Wire
   2.     PCB trace resistance for 1 oz-Cu
   3.     PCB trace resistance for 2 oz-Cu
   4.     Common package type and dimensions
   5.     PCB parallel plate capacitance
   6.     PCB microstrip capacitance and inductance
   7.     PCB adjacent copper traces
   8.     PCB via capacitance and inductance
   9.     Coaxial cable equations
   10.     Notes
8.   Sensor
   1.     Thermistor
   2.     Resistive temperature detector (RTD)
      1.      RTD equation temperature to resistance (T≥0°C and T<0°C)
      2.      RTD equation resistance to temperature (T≥0°C or RRTD ≥ R0)
      3.      RTD equation resistance to temperature (T< 0°C or RRTD < R0)
   3.     Diode equation vs. temperature
      1.      Diode voltage versus temperature
   4.     Thermocouple (J and K)
      1.      Type J thermocouples translating temperature to voltage (ITS-90 standard)
      2.      Type J thermocouples translating voltage to temperature (ITS-90 standard)
      3.      Type K thermocouples translating temperature to voltage (ITS-90 standard)
      4.      Type K thermocouples translating voltage to temperature (ITS-90 standard)
      5.      Thermistor: Resistance to temperature, Steinhart-Hart equation
      6.      Thermistor: Temperature to resistance, Steinhart-Hart equation
   5.     Notes
9.   Digital
   1.     Binary/hex conversions
      1.      Numbering systems: Binary, decimal, and hexadecimal
         1.       Example conversion: Binary to decimal
         2.       Example conversion: Decimal to binary
         3.       Example conversion: Binary to hexadecimal
         4.       Example conversion: Hexadecimal to decimal and decimal to hexadecimal
      2.      Data formats
         1.       Converting two’s complement to decimal: Negative number example
         2.       Converting two’s complement to decimal: Positive number example
   2.     Digital logic thresholds
   3.     Serial peripheral interface
      1.      SPI bus (Serial Peripheral Interface) hardware overview
         1.       Data and control lines
      2.      SPI data latching
         1.       SPI read sequence example
      3.      SPI critical edge
      4.      SPI modes
   4.     Inter-integrated circuit (I2C) bus
      1.      I2C bus (Inter-Integrated Circuit) hardware overview
         1.       Data and control lines
      2.      I2C addressing
      3.      I2C communication
      4.      I2C interface circuitry and rise/fall timing
      5.      I2C pull-up resistor selection
   5.     Notes
10.   ADC
    1.     ADC transfer function
       1.      ADC definitions
       2.      ADC resolution for unipolar
          1.       Full-scale range (FSR) unipolar
       3.      ADC resolution for bipolar
          1.       Full-scale range (FSR) bipolar
       4.      Resolution voltage vs. full-scale range
    2.     Quantization error of ADC
       1.      Quantization error
    3.     Signal-to-noise ratio (SNR) from quantization noise only
    4.     Total harmonic distortion (VRMS)
    5.     Total harmonic distortion (dBc)
    6.     AC signals
       1.      Signal-to-noise and distortion (SINAD) and effective number of bits (ENOB)
    7.     DC signals
       1.      Noise free resolution and effective resolution
    8.     Settling time and conversion accuracy
    9.     ADC system noise calculation
    10.     Effect of clock jitter on ADC SNR
    11.     Notes
11.   DAC
    1.     DAC errors
       1.      DAC definitions
       2.      DAC offset error
       3.      DAC gain error
       4.      DAC zero-code error / negative full-scale error
       5.      DAC bipolar zero error
       6.      DAC full-scale error
    2.     DAC non-linearity
       1.      DAC differential non-linearity
       2.      DAC integral non-linearity
    3.     DAC total unadjusted error
    4.     Notes
12.   Multiplexer
    1.     CMOS switch construction
    2.     ON-resistance (RON)
    3.     RON flatness
    4.     Effective op amp gain including MUX RON
       1.      Design tips
    5.     ON and OFF capacitance (CON/ COFF)
    6.     Leakage current
       1.      Off leakage current
       2.      On leakage current
    7.     Charge injection (QINJ)
    8.     Bandwidth (BW)
    9.     Channel-to-channel crosstalk (XTALK)
    10.     OFF-isolation
    11.     Total harmonic distortion plus noise (THD+N)
    12.     Notes
13.   TI Worldwide Technical Support

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 

Copyright © 2024, Texas Instruments Incorporated